是否可以动态配置逻辑而不是像pll或gtx这样的源

嗨，
不，您不能使用DRP来更改用户逻辑。
动态重新配置使用DRP primtive完成，可以访问FPGA中与HARD BLOCKS相关的寄存器，如DCM，MMCM，GT等。
但是，如果您想要间歇性地更改用户逻辑，则可以使用一个选项，然后您可以在代码中执行某些块的部分重新执行，并使用不同的代码和实现进行替换。
谢谢，AnirudhPS：请将此标记作为答案，以防它有助于解决您的问题。如果帖子引导您找到解决方案，请给予赞誉。
在原帖中查看解决方案



以下为原文

Hi,
 
No, you cannot use DRP for changing user logic.
 
Dynamic reconfiguration is done using the DRP primtive which gains access to the Registers related to the HARD BLOCKS in the FPGA like DCM,MMCM, GT etc. 
 
However one option in case you want to change User Logic intermittently, then you can do Partial reoncifugarion of certain block in your code which you want to replace with a different code and implementation.
 
Thanks,
Anirudh

PS: Please MARK this as an answer in case it helped resolve your query.Give kudos in case the post guided you to a solution.View solution in original post

请详细说明你的帖子http://forums.xilinx.com/xlnx/board/crawl_message?board.id=NewUser&message.id=7717这个主题很少有很好的阅读www.xilinx.com/support/documentation/
application_notes / xapp879.pdf www.xilinx.com/support/documentation/application_notes/xapp888_7Series_DynamicRecon.pdf
谢谢和RegardsBalkrishan -----------------------------------------------
---------------------------------------------请将帖子标记为
一个答案“接受为解决方案”，以防它有助于解决您的查询。如果一个帖子引导到解决方案，请给予赞誉。



以下为原文

please elaborate little more on your post

http://forums.xilinx.com/xlnx/board/crawl_message?board.id=NewUser&message.id=7717

here is few good read on this topic

www.xilinx.com/support/documentation/application_notes/xapp879.pdf

www.xilinx.com/support/documentation/application_notes/xapp888_7Series_DynamicRecon.pdfThanks and Regards
Balkrishan
--------------------------------------------------------------------------------------------
Please mark the post as an answer "Accept as solution" in case it helped resolve your query.
Give kudos in case a post in case it guided to the solution.

嗨，
不，您不能使用DRP来更改用户逻辑。
动态重新配置使用DRP primtive完成，可以访问FPGA中与HARD BLOCKS相关的寄存器，如DCM，MMCM，GT等。
但是，如果您想要间歇性地更改用户逻辑，则可以使用一个选项，然后您可以在代码中执行某些块的部分重新执行，并使用不同的代码和实现进行替换。
谢谢，AnirudhPS：请将此标记作为答案，以防它有助于解决您的问题。如果帖子引导您找到解决方案，请给予赞誉。



以下为原文

Hi,
 
No, you cannot use DRP for changing user logic.
 
Dynamic reconfiguration is done using the DRP primtive which gains access to the Registers related to the HARD BLOCKS in the FPGA like DCM,MMCM, GT etc. 
 
However one option in case you want to change User Logic intermittently, then you can do Partial reoncifugarion of certain block in your code which you want to replace with a different code and implementation.
 
Thanks,
Anirudh

PS: Please MARK this as an answer in case it helped resolve your query.Give kudos in case the post guided you to a solution.

非常感谢



以下为原文

thanks a lot