完善资料让更多小伙伴认识你，还能领取20积分哦， 立即完善>
3天内不再提示
电子发烧友论坛|
您好，我正在尝试使用labview连接到PNA-X N5242A，但我不断收到来自VISA写入功能的错误。
要检查我是否正确连接，我正在使用NI MAX。 它显示连接是正确的，但是当我使用VISA测试面板写操作时，我收到以下错误：VISA：（Hex 0xBFFF003A）无法启动操作，因为安装无效（由于属性设置为不一致状态） 。 当我尝试启动读取操作时，我收到相同的错误。 PNA-X目前正在使用Windows 7和应用程序代码版本A.10.49.03我的代码在使用Windows XP和应用程序代码版本A.09.90.13的另一个PNA-X上运行得非常好。有关错误的屏幕截图，请参阅附件。 写操作Error.png85.8 KBRead Operation Error.png84.3 KB 以上来自于谷歌翻译 以下为原文 Hello, I'm trying to connect to the PNA-X N5242A using LabVIEW, but I kept getting and error coming from the VISA Write Function. To check if I'm connected properly I'm using NI MAX. It shows that the connection is correct, however when I use the VISA Test Panel to write operation I get the following error: VISA: (Hex 0xBFFF003A) Unable to start operation because setup is invalid (due to attributes being set to an inconsistent state). I get the same error when I try to initiate a Read Operation. The PNA-X is currently using Windows 7 and Application Code Version A.10.49.03 My code worked perfectly fine on another PNA-X using Windows XP and Application Code Version A.09.90.13 For screenshots of the errors please see attached. 附件
0
|
|
相关推荐
18个回答
|
|
|
感谢您的帖子...是的，我们知道这个问题：“无法启动操作，因为安装无效（由于属性设置为不一致状态）。”
遗憾的是，只有在客户端PC上安装Keysight IO Libraries时，才支持通过USB控制VNA。 因此，如果您安装Keysight IO Libraries，那么这应该可行。 据我所知，这曾经适用于Windows XP。 它也适用于未来版本的固件（尚未发布）。 但截至目前，您必须使用Keysight IO库通过USB与VNA通信。 以上来自于谷歌翻译 以下为原文 Thank you for your post... Yes, we are aware of this issue: "Unable to start operation because setup is invalid (due to attributes being set to an inconsistent state)." Unfortunately, controlling the VNA over USB is only supported when you install Keysight IO Libraries on your client PC. So, if you install Keysight IO Libraries, then this should work. I understand that this used to work with Windows XP. It will also work with a future version of firmware (yet to be released). But as of now, you must use Keysight IO Libraries to talk to your VNA over USB. |
|
|
|
|
60user56 发表于 2018-9-14 14:41 Keysight IO库可作为辅助VISA安装在带有NI IO库的并行安装中，因此一旦完成并行IO库安装，您就能够从LabView与Keysight USB接口通信 。 以上来自于谷歌翻译 以下为原文 Keysight IO libraries can be installed as secondary VISA in a side-by-side installation with NI IO libraries, so you should be able to talk to a Keysight USB interface from LabView, once you have done the side-by-side IO library install. |
|
|
|
|
Topcbpcba 发表于 2018-9-14 14:56 谢谢你的回复！ 我已经将Keysight IO库安装为辅助VISA，但我仍然遇到同样的错误。 除了简单地安装IO库之外还有什么需要做的吗？ 再次感谢您提供的任何帮助！ 以上来自于谷歌翻译 以下为原文 Thanks for the replies! I've installed the Keysight IO Libraries as a secondary VISA, but I'm still getting the same error. Is there anything else that needs to be done besides simply installing the IO Libraries? Thanks again for any help provided! |
|
|
|
|
|
嗨Scott，Wallace，我们正在尝试在我们的实验室中复制您的场景，看看我们是否可以重现问题并提出解决方案。 您能否告诉我们您正在使用的NI IO库和Labview版本以及作为辅助VISA安装的Keysight IO库的版本？ 以上来自于谷歌翻译 以下为原文 Hi Scott, Wallace, We are currently trying to replicate your scenario here in our lab to see if we can reproduce the problem and propose a solution. Can you both please let us know the NI IO libraries and Labview versions you are using and the version of the Keysight IO libraries that you installed as secondary VISA? |
|
|
|
|
Topcbpcba 发表于 2018-9-14 15:19 我使用的是LabVIEW 2014.1,32位。 但是，如果需要，我可以过渡到2015年。 我正在使用NI MAX 14.5.0f0和NI-VISA 14.0.1我从http://www.keysight.com/en/pd-1985909/io-libraries-suite获得了“Keysight_Instrument_Control_Bundle_2.2016.exe”。 cc = US＆amp; lc = eng但是我正在等待我们的本地IT获得安装许可。 这可能需要一两天。 以上来自于谷歌翻译 以下为原文 I am using LabVIEW 2014.1, 32-bit. However I can transition to 2015 if needed. I'm using NI MAX 14.5.0f0 with NI-VISA 14.0.1 I have acquired "Keysight_Instrument_Control_Bundle_2.2016.exe" from: http://www.keysight.com/en/pd-1985909/io-libraries-suite?cc=US&lc=eng However I am waiting for our local IT for install permission. That may take a day or two. |
|
|
|
|
Topcbpcba 发表于 2018-9-14 15:19 您好Daras，我使用以下内容：NI LabVIEW 2013（32位）NI-VISA 15.0.1（我相信这是NI支持网站上的最新版本）Keysight IO Libraries Suite 17.2（也是Keysight网站上的最新版本） 感谢您的帮助！ 以上来自于谷歌翻译 以下为原文 Hello Daras, I am using the following: NI LabVIEW 2013 (32-bit) NI-VISA 15.0.1 (I believe this is the latest on the NI Support Website) Keysight IO Libraries Suite 17.2 (Also the latest on the Keysight Website) Thank you for the help! |
|
|
|
|
mosen137 发表于 2018-9-14 15:48 我应该提一下，我正在运行64位操作系统，但我使用的是32位LabVIEW。 我已将Keysight IO Library 17.2安装为辅助VISA。 我重新启动了。 我运行了昨天发布的LabVIEW测试程序。 我继续在LabVIEW中收到-1073807302错误。 通过NI MAX，我打开VISA测试面板但是再次出现0xBFFF003A错误。 在NI MAX中我打开工具>> NI-VISA >> VISA选项在“冲突管理器”下我禁用了“National Instruments VISA”（现在只有Agilent VISA可用）。 我重新启动了NI MAX软件。 打开VISA测试面板后，我继续收到0xBFFF003A错误。 我恢复了我的更改：我重新启用了“National Instruments VISA”并将其设置为“首选VISA”。 以上来自于谷歌翻译 以下为原文 I should mention that I am running a 64-bit OS, but am using 32-bit LabVIEW. I have installed Keysight IO Library 17.2 as a secondary VISA. I rebooted. I ran the LabVIEW test program I posted yesterday. I continue to receive the -1073807302 error within LabVIEW. Through NI MAX I open the VISA test panel but again have the 0xBFFF003A error. In NI MAX I opened tools >> NI-VISA >> VISA Options Under "Conflict Manager" I disabled "National Instruments VISA" (now only Agilent VISA is available). I restarted the NI MAX software. Upon opening the VISA test panel I continue to get the 0xBFFF003A error. I reverted my changes: I re-enabled "National Instruments VISA" and set it as the "Preferred VISA". |
|
|
|
|
60user86 发表于 2018-9-14 15:55 嗨斯科特，如果你使用局域网或GPIB连接到PNA，你有同样的问题吗？ 以上来自于谷歌翻译 以下为原文 Hi Scott, Do you have the same problem if you connect to the PNA using LAN or GPIB? |
|
|
|
|
|
此计算机没有GPIB端口。 我不允许将此设备连接到我们的LAN。 以上来自于谷歌翻译 以下为原文 This computer does not have a GPIB port. I am not permitted to connect this equipment to our LAN. |
|
|
|
|
|
我借了USB-to-GPIB适配器。 我发现我没有所需的USB驱动程序。 在ni.com链接后，我从http://search.ni.com/nisearch/app/main/p/bot/no/ap/tech/lang/en/获得了NI-488.2 15.0.0“NI4882_1500f0.exe”。 pg / 1 / sn / catnav：du，n8：3.25.123.785，ssnav：ndr /我安装了驱动程序。 NI MAX现已更新至15.0。 我现在正在使用NI-VISA 15.0。 USB-to-GPIB设备出现在NI MAX中，但继续声明“Windows没有与此设备相关的驱动程序”。 我没有看到使用N5225A设备测试GPIB或LAN通信的直接路径。 尝试通过NI MAX软件VISA测试面板通过USB与N5225A设备通信时，我仍然遇到0xBFFF003A错误。 以上来自于谷歌翻译 以下为原文 I borrowed a USB-to-GPIB adapter. I found I did not have the required USB driver. Following the ni.com link I acquired NI-488.2 15.0.0 "NI4882_1500f0.exe" from http://search.ni.com/nisearch/app/main/p/bot/no/ap/tech/lang/en/pg/1/sn/catnav:du,n8:3.25.123.785,ssnav:ndr/ I installed the driver. NI MAX has now been updated to 15.0. I am now using NI-VISA 15.0. The USB-to-GPIB device appears in NI MAX but continues to state that "Windows does not have a driver associated with this device". I do not see a straight-forward path to test either GPIB or LAN communication with the N5225A device. I continue to experience the 0xBFFF003A error when trying to communicate with the N5225A device over USB via the NI MAX software VISA test panel. |
|
|
|
|
|
根据我以前的帖子，我无法与N5225A仪器建立通信，因为我无法获得“GPIB-USB-A”USB-to-GPIB转换器的工作驱动程序。 但是，我获得了一个“GPIB-USB-HS”USB-to-GPIB转换器，这个接口设备被我的计算机识别。 我在我的计算机和N5225A上的“GPIB（1）Talker / Listener”GPIB端口之间连接了这个接口设备。 使用此配置，我能够成功响应“* IDN？” 使用之前发布的示例.vi程序在我的电脑上查询。 但是，如果可能的话，我更喜欢端到端的USB解决方案。 以上来自于谷歌翻译 以下为原文 Per my previous post I was unable to establish communication with the N5225A instrument because I was unable to acquire a working driver for a "GPIB-USB-A" USB-to-GPIB converter. However, I acquired a "GPIB-USB-HS" USB-to-GPIB converter instead and this interface device was recognized by my computer. I connected this interface device between my computer and the "GPIB (1) Talker/Listener" GPIB port on the N5225A. Using this configuration I was able to get a successful response to a "*IDN?" query on my PC using the example .vi program posted previously. However, I would prefer an end-to-end USB solution if possible. |
|
|
|
|
60user86 发表于 2018-9-14 16:52 嗨斯科特，感谢您的更新，我很高兴USB到GPIB正在运行。 我们能够重现您的问题，我们的开发团队正在研究解决方案。 我们将深入探讨这个问题。 以上来自于谷歌翻译 以下为原文 Hi Scott, Thank for the update and I am glad that the USB to GPIB is working now. We were able to reproduce your issue and our development team is working on a solution to fix it. We will get to the bottom of this issue. |
|
|
|
|
|
这是个好消息，非常感谢您的继续支持。 以上来自于谷歌翻译 以下为原文 That is excellent news, thank you very much for your continued support. |
|
|
|
|
|
PNA固件的新版本解决了PNA的Labview / USB连接问题，可作为测试版发布。 如果您想尝试一下，请将您的电子邮件信息告诉我，我会将链接发送给您。 以上来自于谷歌翻译 以下为原文 A new version of the PNA firmware that solves the Labview/USB connection problems with the PNA is available as a beta release. If you would like to try it out, please PM me with your email information and I will send you the link. |
|
|
|
|
|
你好Jad，这个问题有没有进展？ 我没有像Scott那样访问USB到GPIB，只能使用USB到USB的连接。 以上来自于谷歌翻译 以下为原文 Hello Jad, Has there been any progress with the issue? I do not have access to a USB to GPIB like Scott does and can only make use of the USB to USB connection. |
|
|
|
|
|
嗨Daras
我和MSOX4024A有类似的问题。 使用USB连接时。 您是否有更新的固件来解决此问题？ 欢呼， 理查德杨 以上来自于谷歌翻译 以下为原文 Hi Daras I have a similar issue with MSOX4024A. when connecting using USB. Do you have an updated firmware to solve this issue? Cheer, Richard yang |
|
|
|
|
|
你安装了什么FW？ 以上来自于谷歌翻译 以下为原文 What FW do you have installed? |
|
|
|
|
|
嗨Hognala， 今天我尝试通过Keysight连接专家发送命令 上面的pic是我在selftest之后找到的错误代码。 FM应该是第三部分吗？ - > * IDN？ 以上来自于谷歌翻译 以下为原文 Hi Hognala, Today I try to send command though Keysight connection expert above pic is the error code I found after selftest. FM should be the third segment ? -> *IDN? <- AGILENT TECHNOLOGIES,MSO-X 4024A,MY56310481,04.08.2016071800 Cheers, Richard |
|
|
|
|
只有小组成员才能发言，加入小组>>
1234 浏览 0 评论
2352 浏览 1 评论
2163 浏览 1 评论
2028 浏览 5 评论
2912 浏览 3 评论
979浏览 1评论
关于Keysight x1149 Boundary Scan Analyzer
711浏览 0评论
N5230C用“CALC:MARK:BWID？”获取Bwid,Cent,Q,Loss失败，请问大佬们怎么解决呀
811浏览 0评论
1236浏览 0评论
/6 
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 （电路图） 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证：合字B2-20210191
工商网监
湘ICP备2023018690号
6062
评论
淘帖
1733
