完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
你好,
我需要了解CY7C6562 28 QFPN,如果我想避免使用EEPROM,系统将如何运行。默认值是多少。按照流程图,它提到的默认值,但没有得到它是什么。设备会在主机和设备之间路由数据吗? 谢谢您, 以上来自于百度翻译 以下为原文 Hi, I need to understand with CY7C65642 28QFPN if i want to avoid using EEPROM, how system will behave. What is the default values it take. As per flow chart its mentioned default value, but did not get what it is. Will device route the data between host and device? Thank you, |
|
相关推荐
7个回答
|
|
你好阿伦斯,
默认情况下,该中心已在内部ROM. An EEPROM得到了其配置可以随意添加外部如有需要修改某些参数如VID/PID,移动端口、集线器IC等有其整个固件本身,因此数据路由之间的HOST和设备在没有EEPROM存在的情况下发生。 最好的问候, 斯里纳斯 以上来自于百度翻译 以下为原文 Hello Arun KS, By default, the hub has got its configurations in an internal ROM. An EEPROM can optionally be added externally in case there is a need to modify certain parameters such as VID/PID, number of removable ports, etc. The hub IC has got its entire firmware in itself and hence the data routing between host and device occurs without the presence of EEPROM too. Best regards, Srinath S |
|
|
|
wangcong12138 发表于 2018-9-4 18:39 你好, 我的定制设计cy7c65642引脚12,13,15,16映射为USB设备和作为输出引脚1,2。 我没有EEPROM连接的枢纽,与这个设置我无法看到设备已经列举了从主机。 请让我知道将内部ROM设置默认端口选择,我不想改变PID和VID,总是端口是固定的。 默认值将所有输入端口启用或不。 我可以分享示意请让我知道你的邮件ID。 谢谢您, 阿伦 以上来自于百度翻译 以下为原文 Hi, With my customized design CY7C65642 pin 12,13,15,16 is mapped for USB device and pin 1,2 is used as output. I am not having eeprom connected to hub, with this setting i am not able to see device is getting enumerated from host. Pl let me know what will be default port selection with internal ROm setting,I do not want to change PID/VID, always ports are fixed. With default values will all input port is enabled or any not. I can share schematic please let me know your mail id. Thank you, Arun |
|
|
|
q510954672 发表于 2018-9-4 18:46 你好阿伦斯, 请,让我知道如果集线器是被列举在PC主机。设备管理器显示枢纽“通用串行总线控制器”下的部分。如果可能的话,请共享设备管理器的屏幕截图。 最好的问候, 斯里纳斯 以上来自于百度翻译 以下为原文 Hello Arun KS, - Kindly, let me know if the hub is getting enumerated on the PC host. The device manager should display the hub under the 'Universal Serial Bus Controllers' section. Please share the screenshot of device manager if possible. Best regards, Srinath S |
|
|
|
wangcong12138 发表于 2018-9-4 18:59 你好, 主机没有枚举2集线器。 以上来自于百度翻译 以下为原文 HI, Host is not enumerating the 2.0 Hub. |
|
|
|
你好阿伦斯, 请分享Srnt@ CyPress的示意图。 最好的问候, 斯里纳斯 以上来自于百度翻译 以下为原文 Hello Arun KS, Please share the schematics to srnt@cypress.com Best regards, Srinath S |
|
|
|
嗨,Srinath, 我们观察到,接地引脚27后,即测试I2CYSCL,主机POPs设备未识别消息。需要了解SCL线路如何配置,如果我们想与EEPROM挂钩? 或者,如果我们没有EEPROM,用这个28引脚封装,这条线的设置是什么? 按数据表 2CYSCL 27 I(RDN)I/O(RDN)测试。0:正常操作和1:芯片将置于测试模式。 I2CYSCL。可以作为I2C时钟引脚来访问I2C EEPROM。 以上来自于百度翻译 以下为原文 Hi Srinath, We observed that, after grounding Pin 27 i.e Test I2C_SCL, host pops device not recognized message. Need to understand how SCL line has to configured if we want to hook with EEPROM? or in other way with this 28 pin package if we do not have EEPROM, what will be the setting of this line? As per data sheet 2C_SCL 27 I(RDN) I/O(RDN) Test. 0: Normal Operation and 1: Chip will be put in test mode. I2C_SCL. can be used as I2C clock pin to access I2C EEPROM. |
|
|
|
q510954672 发表于 2018-9-4 19:47 你好,Arun, 当设备需要连接到一个EEPROM,离开SCL引脚浮和SDA线拉高。当EEPROM相连,SDA / PWR引脚作为I2C SDA引脚和不作为动力使。当EEPROM是目前,如果测试/ i2c_scl引脚被拉低,主人将无法驱动时钟的针,因此描述符查询失败。 当没有EEPROM是连接,SDA / PWR引脚作为电源使能引脚和SCL引脚可以被拉低。 最好的问候, 斯里纳斯 以上来自于百度翻译 以下为原文 Hello Arun, - When the device needs to be connected to an EEPROM, leave the SCL pin floating and pull the SDA line HIGH. When the EEPROM is connected, the SDA/PWR pin acts as I2C SDA pin and not as the power enable. When the EEPROM is present, if the TEST/I2C_SCL pin is pulled LOW, the master will not be able to drive the clock on the pin and hence the descriptor query fails. - When no EEPROM is to be connected, SDA/PWR pin acts as power enable pin and the SCL pin can be pulled LOW. Best regards, Srinath S |
|
|
|
只有小组成员才能发言,加入小组>>
716个成员聚集在这个小组
加入小组1901 浏览 1 评论
1652 浏览 1 评论
3405 浏览 1 评论
请问可以直接使用来自FX2LP固件的端点向主机FIFO写入数据吗?
1568 浏览 6 评论
1380 浏览 1 评论
CX3连接Camera修改分辨率之后,播放器无法播出camera的画面怎么解决?
188浏览 2评论
184浏览 2评论
使用stm32+cyw43438 wifi驱动whd,WHD驱动固件加载失败的原因?
322浏览 2评论
352浏览 1评论
63浏览 1评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-4-24 23:44 , Processed in 0.775104 second(s), Total 79, Slave 63 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号