完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
当跳线J9连接到3.3V时,PSoC4 ADC可以用单端检测0V-5V吗?我想把Vref(P1(7))连接到5V,这是正确的方法吗?我想做八通道ADC 0V到5V。
以上来自于百度翻译 以下为原文 Can the psoc4 Adc be used to sense 0v-5v with single ended when jumper J9 is connected to 3.3v? I want to connected Vref (P1[7]) to 5v Is this th right way to go? I want to do eight channel Adc 0v to 5v. |
|
相关推荐
3个回答
|
|
…当然,VREF可能不超过模拟电源。
鲍勃 以上来自于百度翻译 以下为原文 ... and of course the Vref may not exceed analog supply. Bob |
|
|
|
使用3.3 V但期望5 V ADC范围的后果
在多通道设计中需要一个(R)衰减器。 每个输入。或使用外部MUX与3.3 V控制驱动器, 5V的输入范围,然后由一个衰减器。所以你会 必须做一个错误预算来确定设计是否符合你的设计 在任何情况下的目标。 如果你有一个电源,3.3 V,作为一个来源,考虑一个 升压转换器,来自不同厂商的许多产品,来自SW CAP 基于L的Boost变换器的设计。注意一些PSoC的 内部升压转换器,PSoC 1和3。 此外,数据表不完整的VSSA,VSS和 Vdda,Vdd。 HTTP://www. CyPress?COM/?APP =论坛和ID ID=2492和;RID=90735 问候,Dana。 以上来自于百度翻译 以下为原文 The consequences of using 3.3 V but desiring 5 V ADC range in a multichannel design would require an (R) attenuator on each input. Or use an external mux with 3.3 V control drive, 5V input range followed by a single attenuator. So you would have to do an error budget to determine if design meets your goals in any event. If all you have as a power source, 3.3 V, as a source, consider a boost converter, many offerings from various vendors, from sw cap designs to L based boost converters. Note some PSOC's have an internal boost converter, PSOC 1 & 3. Also datasheet incomplete regarding relationship of Vssa, Vss and Vdda, Vdd. http://www.cypress.com/?app=forum&id=2492&rID=90735 Regards, Dana. |
|
|
|
使用R除法器的另一个考虑因素是影响
正在测量的测量节点的信号加载, 当然还有速度和稳定时间对SAR歌剧的影响—— tion. 所有这些在很大程度上可以通过在5V的操作部件来减轻。 使用PSoC 1或3带有内部升压转换器。 问候,Dana。 以上来自于百度翻译 以下为原文 One other consideration to using R dividers, is impact on signal loading of the measurement node you are examining, and of course speed and settling time impact on SAR opera- tion. All this can be largely mitigated by operating part at 5V. Or use PSOC 1 or 3 with internal boost converters. Regards, Dana. |
|
|
|
只有小组成员才能发言,加入小组>>
718个成员聚集在这个小组
加入小组1910 浏览 1 评论
1664 浏览 1 评论
3418 浏览 1 评论
请问可以直接使用来自FX2LP固件的端点向主机FIFO写入数据吗?
1580 浏览 6 评论
1387 浏览 1 评论
CX3连接Camera修改分辨率之后,播放器无法播出camera的画面怎么解决?
207浏览 2评论
194浏览 2评论
使用stm32+cyw43438 wifi驱动whd,WHD驱动固件加载失败的原因?
336浏览 2评论
364浏览 1评论
74浏览 1评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-5-10 03:00 , Processed in 0.829370 second(s), Total 50, Slave 44 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号