设备未检测到

在KIT-1001上没有两个USB连接器吗？一定要用正确的。
鲍勃



     以下为原文
  Aren't there two USB-connectors on the Kit-001? Make sure you use the correct one.
     
    Bob

要调试KIT-1001上的项目，您需要使用MIXPROP3而不是车载USB端口。在KIT-1001上没有板上的程序员/调试器，就像KIT-030和KIT-050上有一个。
为了重申，您应该通过微带电缆将MimPrim3连接到PosiSeror模块上的10针调试端口，以便调试CY8CKIT-01上的程序。



     以下为原文
  To debug the project on KIT-001, you would need to use Miniprog3 and not the on board USB port. There is no on-board programmer/debugger on KIT-001 like there is one on KIT-030 and KIT-050.
     
    To reiterate, you should connect a miniprog3 to the 10 pin debug port on the porcessor module through the ribbon cable in order to debug the program on CY8CKIT-001.

谢谢QS帮我把这件事甩在后面，我已经习惯于思考了
大约030岁，050岁，我忘记了001岁……
问候，Dana。



     以下为原文
  Thanks QS for bailing my rear out on this one, I am so used to thinking
    about -030, -050, I forget about the -001........
     
    Regards, Dana.

您的安装应该是这样的&功率001工具包使用12V适配器-gt；连接MyPrim3到PSoC3处理器模块，通过JTAG电缆-GT；将USB电缆连接在MimePrime3的一端到PC的USB端口之间。
如果Windows首次连接到该端口，您应该看到Windows正在尝试安装MyPrim3的驱动程序。如果您想确认是否安装了合适的驱动程序，请转到设备管理器，在USB下，您应该看到MIXPROP3。
如果你能看到这一点，然后打开PSoC程序员/创建者，并尝试编程。如果您收到任何错误信息，请在这里附加。
如果你不能看到正确的驱动程序被安装，那么按照这个KB文章中提到的步骤——HTTP://wwwyCysP.COM/？ID＝4和；RID＝45812。不是指向KTK文章中解释的FTK驱动程序，而是指向PSoC程序员安装的位置中的MPRO3驱动程序。



     以下为原文
   Your setup should be like this -> Power -001 Kit using 12V adaptor -> Connect MiniProg3 to the PSoC3 processor module via JTAG cable -> Connect the USB cable between one end of MiniProg3 to PC's USB port.
     
    You should see that Windows is trying to install the driver for the MiniProg3 if it is connected to that port for the first time. If you want to confirm whether appropriate driver is installed or not, go to device manager and under USB, you should see MiniProg3.
    If you are able to see that, then open PSoC Programmer/Creator and try to program. If you get any error message, attach that here.
    If you are not able to see the proper driver getting installed, then follow the steps mentioned in this KB article - http://www.cypress.com/?id=4&rID=45812. Instead of pointing to FTK driver as explained in the KB article, point to mprog3 driver inside the PSoC Programmer installed location.

我已经连接了MyPrim3并在设备管理器中检测到了驱动程序。
运行端口获取时出错。可能没有设备附加或设备可能在另一个应用程序中使用。



     以下为原文
   I have connected the miniprog3 and the driver was detected in the device manager.I got the following error message 
    There was an error running port acquire. There may be no devices attached or a device may be in use by another application.

我花了很长时间和那个错误的消息打交道，直到我找到了解决办法。关闭所有程序，重新安装CyPress软件和一批重新启动，对我来说似乎没什么用。
然后我决定清理通过我的计算机的生命迄今收集到的USB依赖关系。我安装了一些免费软件来管理USB设备（见附件），然后（很重要！）分离我的USB连接并卸载大部分收集的设备（我离开USB集线器，我的键盘，鼠标等）
重启并修复了一些错误之后，我附上了MIXPROP3…瞧！它又工作了！！！！
我希望这对你也有帮助。
快乐重启
鲍勃



     以下为原文
  I had a long fight with that errormessage until I found a solution for me. Closing all programs, re-installing Cypress-software and a bunch of re-bootings, nothing seems to work for me.
    Then I decided to clean up the USB-dependencies that have been collected so far through the lifetime of my computer. I installed some free software to manage USB devices (See attached picture), then (IMPORTANT!) detached my USB-Connections and de-installed most of the collected devices (I left the USB-Hubs, my keyboard, mouse etc)
    After a reboot and fixing some of the errors I made, I attached the miniprog3 ... and lo! it worked again!!!
    I hope this will help you too.
     
    Happy re-booting
    Bob

我尝试重新启动，唉不工作！！



     以下为原文
   I tried re-booting, alas doesnt work !!

为什么不试着从www. CyPress？COM/GO/支持打开一个技术支持案例？



     以下为原文
   Why don't you try opening a Tech support case from www.cypress.com/go/support ?

支持USB集线器的ISCY8C38 66 AXI支持



     以下为原文
  is cy8c3866axi support for u*** hub

我需要读和写文件从PixRiver使用CY8C38 66 AXI USB2.0，我不知道做R/W请任何人帮助我



     以下为原文
   i need to read and write files from pendrive using cy8c3866axi u***2.0, i dont know do to R/W please anyone help me

@切蒂：请不要杰克存在新问题的线程。这条线索与你的问题无关，所以不可能有人在这里帮助你。（除此之外，它只有几个月大）。因此，请打开一个新的线程，适当的主题。
谢谢！



     以下为原文
  @citti: please don't hi-jack existing threads with new question. This thread has nothing to do with your question, so it is unlikely someone helps you here. (Apart from that, it is just several months old). So please open a new thread, with an appropriate subject.
    Thanks!