CY8CMBR3110与miniprog 3不能编程

“EZ点击”应用程序可用于配置MBR31 10设备。
首先，请允许我确认您可以使用MIXPROP3识别MBR31 10。
当MPRY3与MBR31 10连接到PC时，PSoC程序员可以识别MIXPROP3。然后点击“校验和”按钮，PSoC程序员可以识别该设备是MBR31 10，校验和得到如下。
桥梁控制面板应用可用于检测MRB31设备。在设置电源电压和协议并提供电源后，点击“列表”按钮多次。您可以看到M231的I2C地址。
“列表”按钮必须多次单击的原因是，MBR31 10通常处于低功耗模式，并通过I2C通信唤醒。
在创建项目后，您还可以使用EZ单击应用程序识别MBR31 10设备。在这种情况下，我认为“桥牌控制面板”比“EZ点击”更容易。
当做，
诺里基



     以下为原文
  The "EZ-Click" application can be used to configure the MBR3110 device.
 
At first, please let me confirm you can recognize the MBR3110 with the MiniProg3.
 
When the MiniProg3 with MBR3110 is connected to the PC, the PSoC Programmer can recognize the MiniProg3.  Then the "Checksum" button is clicked, the PSoC Programmer can recognize the device is the MBR3110 and the checksum is gotten as follows.

 
The Bridge Control Panel application can be used to detect the MBR3110 device.  After setting the power supply voltage and the Protocol and providing power supply, click the "List" button multiple times.  You can see the I2C address of the MBR3110.

The reason why the "List" button must be clicked multiple times is the MBR3110 is typically in a low-power mode and wakes up by the I2C communication.
 
You can also recognize the MBR3110 device with the EZ-Click application after a project is created.  I think "Bridge Control Panel" is easier than the "EZ-Click" in this case.
 
Regards,
Noriaki

你好！
我尝试了桥梁控制面板（3.3V和5.0V），但不工作，因为
在那张照片里看到了！
现在
最好的问候
2017～11-01 10:43 GMT-02:Nikai-TanaK＆LT；社区经理@ CyPress
& http://www. Copress。com & gt；
柏树开发者社区
HTTPS://Cullist.CyPress？COM/？ET=手表，电子邮件，线程& GT；
MILPROG 3编程问题CY8CMBR31
Noriaki Tanaka的回复
HTTPS://Cullist.CyPl.com /PoePs/NTAN？ET=手表，电子邮件，线程& gt；在*PSoC中
3＊-充分讨论
HTTPS://Cullist.CyPl.com／MaseGe/14538？ET=手表，电子邮件。线程α145385和gt；
WhatsApp图像2011-11-01在1127.10（1）JPEG
83.6 K
WhatsApp图像2011-11-01在1127.47.JPEG
106.3 K



     以下为原文
  Hi!
 
I tried with Bridge Control Panel (with 3.3V and 5.0V), but not working, as
seen in then attchament picture!
 
and now
 
best regards
 
2017-11-01 10:43 GMT-02:00 Noriaki Tanaka <community-manager@cypress.com>:
 

<http://www.cypress.com>
Cypress Developer Community
<https://community.cypress.com/?et=watches.email.thread>
Problem programming CY8CMBR3110  with miniprog 3
 
reply from Noriaki Tanaka
<https://community.cypress.com/people/ntan?et=watches.email.thread> in *PSoC
3* - View the full discussion
<https://community.cypress.com/message/145385?et=watches.email.thread#145385>

 

•   WhatsApp Image 2017-11-01 at 11.29.10(1).jpeg 83.6 K
  
  
•   WhatsApp Image 2017-11-01 at 11.29.47.jpeg 106.3 K
  
  

谢谢你的回复。
我知道MixPrim3与MBR31 10之间的连接存在问题。
首先，请确认电源线和I2C线在拆下其他电线到传感器后。下面是我的电路板和它的原理图。
最重要的是旁路电容器的位置。旁路电容器必须靠近MBR31 10。我看到你正在使用针间距转换板。你把旁路电容器0.1UF和1UF放在转换板上了吗？如果没有，MBR31 10将无法工作。
VCC引脚具有0.1UF电容器作为内部调节器的旁路电容器。这个电容器必须靠近MBR31 10。
当做，
诺里基



     以下为原文
  Thank you for your reply.
 
I understand that the connection between the MiniProg3 and the MBR3110 has problem.
 
At first please confirm the power and I2C lines after removing other wires to sensors.  Following is my board and its schematic.


The most important thing is the location of the bypass capacitors.  Bypass capacitors must be put close to the MBR3110.  I see you are using the pin pitch conversion board.  Did you put the bypass capacitors 0.1uF and 1uF on the conversion board?  If not, MBR3110 would not work.
The VCC pin has a 0.1uF capacitor as a bypass capacitor for an internal regulator.  This capacitor must be put close to the MBR3110 too.
 
Regards,
Noriaki