是否有必要更新ATWINC1500固件以使用AT命令？

嗨，我正在使用RAT232通过AT23WC1500发送启动命令：A5 01 F2 00 00 0C 00 0C 00 61 2F 52 EFAND，我得到以下响应：（0）没有CopTutsApp（0）（M2M）DRIVILFION:无。假设19.3.0（0）芯片ID＝1524B0（0）Flash ID＝B512302C，大小＝4 Mbit（10）EFUES:MAC（10）MACYADDR＝8F:F4:35:Ab:8C:13（10）共享Buff静态：0, 5, 5、22, 9, 10（20）NMI M2M SW版本19.5.2 SvnReV 14274（30）NMI MIN DRV版本19.3.0（30）固件Svn URL分支/WiFiOT-166019195Y2RC7（II）26 2017 22:13:34（40）ROM LIB VILY2（40）×AESHHWYEngEngEngII（40）（M2M）负载SEC（50）（TLS）TLS会话大小＝1884（70）PSMO，但是根据AT命令的文档应该得到类似如下的响应：响应+OK+AT＝AT：，FW:，CHIPID:：RFRVV在上述之后，我发送“检查AT命令”。固件“如下：但没有响应模块。预先欢迎任何意见或建议。



      以下为原文

    Hi.

I am using the ATWINC1500 via RS232 and sent the start command:

A5 01 F2 00 00 0C 00 0C 00 61 2F 52 EF

And I get the following response:


(0)NO CORTUS app
(0)(M2M)DriverInfo: None. Assuming 19.3.0
(0)Chip ID = 1524b0
(0)Flash ID = b512302c, Size = 4 MBit
(10)EFUSE:MAC
(10)MAC_ADDR = 8F:F4:35:AB:8C:13
(10)Shared buff static: 0, 5, 5, 22, 9, 10
(20)NMI M2M SW VERSION 19.5.2 SVNREV 14274
(30)NMI MIN DRV VERSION 19.3.0
(30)Firmware SVN URL branches/WIFIIOT-1660_19_5_2_RC7
(30)Built at Jan 26 2017 22:13:34
(40)ROM LIB VER_2
(40)__AES_HW_ENGINE__
(40)(M2M)LOAD SEC
(50)(TLS)TLS Session Size= 1884
(70)PSM_OFF

But according to the document AT commands should get a response something similar to the following:

Response +OK+AT=AT:,FW:,ChipID:,RFRev

After the above, I send the "Check the AT Command Firmware" as follows:

case CHECK_AT_COMMAND_FIRMW:{
            app_uart1.transmissionBuffer[0x00] = 'A';
            app_uart1.transmissionBuffer[0x01] = 'T';
                        
            app_uart1.transmissionBuffer[0x02] = 0x0D;
            app_uart1.transmissionBuffer[0x03] = 0x0A;
            
            app_uart1.sizeToTransmit = 0x04;
            break;
        }

But there is no response from the module.


In advance any comments or suggestions are welcome.