ISE 11.3中的smartxplorer错误，如何在命令行中启动smartxplorer？

我输入以下命令，如“
smartxplorer -p xc5vlx155t-ff1136-1 -uc mucus_top_b1.ucf -sd ngc_files mucus_top.edf
“，但程序立即退出。我发现了一个日志文件，如下所示（smartxplorer.log）。如果我输入这样的命令”smartxplorer -p xc5vlx155t-ff1136-1 -uc mucus_top_b1.ucf -sd ='。;
ngc_files'mucus_top.edf“，程序立即退出但没有生成任何日志文件。
smartxplorer.log内容：
版本11.3 SmartXplorer版权所有（c）1995-2009 Xilinx，Inc。保留所有权利.smartxplorer -p xc5vlx155t-ff1136-1 -uc mucus_top_b1.ucf -sd ngc_files mucus_top.edf
SmartXplorer设置：
designName = G： mucus_b1_bitfile  20100505_7_8  implement  run  mucus_top.edf write_dir = G： mucus_b1_bitfile  20100505_7_8  implement  run host_list =无part = xc5vlx155t-ff1136-1 strategy_file =无notify =无source_dir = G： mucus_b1_bitfile
20100505_7_8  implement  run  ngc_files ucf = G： mucus_b1_bitfile  20100505_7_8  implement  run  mucus_top_b1.ucf batch_mode = False run_all_strategies = False list_all_strategies = False remote_command = rshmulti_threading = off
错误：输入设计文件出现问题，即.xst，.prj等.Smartxplorer退出



以下为原文

I input the following commands like this "
smartxplorer -p xc5vlx155t-ff1136-1 -uc mucus_top_b1.ucf -sd ngc_files mucus_top.edf
", but the program drop out immediately. I found a log file as followss (smartxplorer.log) is generated. if I input commands like this "smartxplorer -p xc5vlx155t-ff1136-1 -uc mucus_top_b1.ucf -sd='.;ngc_files' mucus_top.edf", The program drop out immediately but without any log files generated.

smartxplorer.log content:

Release 11.3 SmartXplorer
Copyright(c) 1995-2009 Xilinx, Inc. All rights reserved.
smartxplorer -p xc5vlx155t-ff1136-1 -uc mucus_top_b1.ucf -sd ngc_files mucus_top.edf
SmartXplorer Settings:
designName=G:mucus_b1_bitfile20100505_7_8implementrunmucus_top.edf
write_dir=G:mucus_b1_bitfile20100505_7_8implementrun
host_list=None
part=xc5vlx155t-ff1136-1
strategy_file=None
notify=None
source_dir=G:mucus_b1_bitfile20100505_7_8implementrunngc_files
ucf=G:mucus_b1_bitfile20100505_7_8implementrunmucus_top_b1.ucf
batch_mode=False
run_all_strategies=False
list_all_strategies=False
remote_command=rsh
multi_threading=off
ERROR: Problem with input design files, i.e. .xst, .prj etc. Smartxplorer quits