MiniProg3不起作用

在创建者的调试中，您可以尝试“附加到运行目标”选项吗？
MIXPRO3使用的是复位模式编程还是功率循环编程模式？



     以下为原文
  Can you try the option "Attach to running target" under Debug in Creator.
MiniProg3 is using reset mode of programming or Power Cycle mode of programming?

嗨，安得烈，
除了移动SW7之外，你还改变了什么？
我可以用你的同样的情节来精细地编程和调试。
即使SW7正确切换，备份域的电源实际上也不会切换到超级电容器，因为只要DimePrim3向电路板供电，VDDD总是被提供。
如果VDDD可用，备用电源开关将始终选择VDDD作为电源。如果用户想使用V备份作为调试域的备份域电源，在BuffuUCTL寄存器中的VDDBAKJCTL位字段应该设置为非零值。
此外，请首先启用超级CAP（通过VDDE当VDDD可用），通过写“3C”到EnthCujGyKEY位字段在BuffupCTL寄存器中。



     以下为原文
  Hi Andrew,
 
What else you have changed other than moving sw7 to super cap on the board?
 
I can program and debug finely with same scenario of yours.
The power supply of backup domain maybe actually not switched to super cap even though sw7 switched correctly, because VDDD is always supplied as long as Miniprog3 supplies power to the board.
If VDDD is available, backup power switch will always selects VDDD as power source. If the user wants to use VBACKUP as backup domain power source for debug purpose, the VDDBAK_CTL bitfield in the BACKUP_CTL register should be set as non-zero value.

Also, please enable charging the super cap firstly(through VBACKUP when VDDD is available), by writing "3C" to the EN_CHARGE_KEY bitfield in the BACKUP_CTL register.

返回SW7到VDD/KiTrp2没有任何影响。
SW6被设置为PSoC 6 BLE。
我已经尝试了所有的时钟速度，现在设置为0.2兆赫。
我使用SWD协议，10引脚，复位获取，3.3电源。（以下错误）
设置电源外部电源和电源（12VDC）与J9。（以下错误）
那么，我做错了什么？



     以下为原文
  Returning sw7 to VDDD/KitProg2 has no affect.
 
sw6 is set to PSoC 6 BLE.
 
I have tried all clock speeds; now set at 0.2 MHz.
 
I am using SWD protocol, 10 pin,  Reset acquire, and 3.3 power. (Error Below)

Setting power to External and supplying power (12VDC) with J9. (Error Below)

So what I am doing wrong?

我撤回了我的步骤，并能够编程和调试。我把电源换成了板凳电源，而不是墙上的疣。然后我从PSoC 6程序员开始，并尝试了创建者后，这是工作。一切都被更新了，所以不是这样。然而，这是RTC的演示，而不是主要的项目。
关键是要有一个没有KiPrd2的工厂程序员。
我在主语（）中有下面的行（对于ANK）。
CythySpMyBuffuP超级电容器（CythySypMsScCARGEGLE启用）；
这仍然存在问题：
没有UARTSW7被设置为KiTr2感谢。



     以下为原文
  I retraced my steps and was able to program and debug. I changed Power supplies to a bench supply instead of a wall wart. I then started with the PSoC 6 programmer and tried the Creator after that was working. Everything was updated, so that wasn't it.  However, this was a demo of the RTC and not the main project.
 
The main point is to have a factory programmer without KitProg2.
 
I did have the line below in main() (for anks).
 
Cy_SysPm_BackupSuperCapCharge( CY_SYSPM_SC_CHARGE_ENABLE );
 
This still has problems:

• no uart
  
• sw7 is set to KitProg2
  

Thanks.