完善资料让更多小伙伴认识你，还能领取20积分哦， 立即完善>
3天内不再提示
电子发烧友论坛|
下面是微信的测试摇一摇，肯定摇得到，其他跟微信相关的属于应用问题，需要自己去看微信的标准改了。//微信的测试摇一摇
static uint8 advertData[] = [ // Preamble: 0x4c000215 // 02 01 06 1A FF 4C 00 02 15: iBeacon prefix (fixed) // UUID: E2C56DB5-DFFB-48D2-B060-D0F5A71096E0 // Major: 1 (0x0001) // Minor: 1 (0x0001) // Measured Power: -59 (0xc5) 0x02, 0x01, 0x06, 0x1a, 0xff, 0x4c, 0x00, 0x02, 0x15, 0xfd, 0xa5, 0x06, 0x93, 0xa4, 0xe2, 0x4f, 0xb1, 0xaf, 0xcf, 0xc6, 0xeb, 0x07, 0x64, 0x78, 0x25, 0x00, 0x0a, 0x00, 0x04, 0xc5 ]; 安装 TI 官方的 CC254x 开发环境 复制 C:Texas InstrumentsBLE-CC254x-1.3.2ProjectsbleSimpleBLEBroadcaster 文件夹 粘贴到：C:Texas InstrumentsBLE-CC254x-1.3.2ProjectsbleiBeacon 运行 IAR Embedded Workbench，点击 File > Open > Workspace 修改源代码 simpleBLEBroadcaster.c // GAP - Advertisement data (max size = 31 bytes, though this is // best kept short to conserve power while advertisting) static uint8 advertData[] = [ // Flags; this sets the device to use limited discoverable // mode (advertises for 30 seconds at a time) instead of general // discoverable mode (advertises indefinitely) 0x02, // length of this data GAP_ADTYPE_FLAGS, GAP_ADTYPE_FLAGS_BREDR_NOT_SUPPORTED, // three-byte broadcast of the data "1 2 3" 0x04, // length of this data including the data type byte GAP_ADTYPE_MANUFACTURER_SPECIFIC, // manufacturer specific advertisement data type 1, 2, 3 ]; 修改下面关键字 UID: E2C56DB5-DFFB-48D2-B060-D0F5A71096E0 Major: 1 (0x0001) Minor: 1 (0x0001) Measured Power: -59 (0xc5) // GAP - Advertisement data (max size = 31 bytes, though this is // best kept short to conserve power while advertisting) static uint8 advertData[] = [ // 25 byte ibeacon advertising data // Preamble: 0x4c000215 // UUID: E2C56DB5-DFFB-48D2-B060-D0F5A71096E0 // Major: 1 (0x0001) // Minor: 1 (0x0001) // Measured Power: -59 (0xc5) 0x1A, // length of this data including the data type byte GAP_ADTYPE_MANUFACTURER_SPECIFIC, // manufacturer specific advertisement data type 0x4c, 0x00, 0x02, 0x15, 0xe2, 0xc5, 0x6d, 0xb5, 0xdf, 0xfb, 0x48, 0xd2, 0xb0, 0x60, 0xd0, 0xf5, 0xa7, 0x10, 0x96, 0xe0, 0x00, 0x01, 0x00, 0x01, 0xc5 ]; 接下来修改广播类型，将下面代码 //uint8 advType = GAP_ADTYPE_ADV_NONCONN_IND;// use non-connectable advertisements uint8 advType = GAP_ADTYPE_ADV_DISCOVER_IND; // use scannable unidirected advertisements 修改为 uint8 advType = GAP_ADTYPE_ADV_NONCONN_IND; // use non-connectable advertisements //uint8 advType = GAP_ADTYPE_ADV_DISCOVER_IND; // use scannable unidirected advertisements 接下来修改 GAP // Set the GAP Role Parameters GAPRole_SetParameter( GAPROLE_ADVERT_ENABLED, sizeof( uint8 ), &initial_advertising_enable ); GAPRole_SetParameter( GAPROLE_ADVERT_OFF_TIME, sizeof( uint16 ), &gapRole_AdvertOffTime ); GAPRole_SetParameter( GAPROLE_SCAN_RSP_DATA, sizeof ( scanRspData ), scanRspData ); GAPRole_SetParameter( GAPROLE_ADVERT_DATA, sizeof( advertData ), advertData ); GAPRole_SetParameter( GAPROLE_ADV_EVENT_TYPE, sizeof( uint8 ), &advType ); 因为 iBeacon 必须不间断广播，并且不响应任何数据请求，所以我们要修改 GAPROLE_ADVERT_OFF_TIME 和 GAPROLE_SCAN_RSP_DATA。 // Set the GAP Role Parameters GAPRole_SetParameter( GAPROLE_ADVERT_ENABLED, sizeof( uint8 ), &initial_advertising_enable ); //GAPRole_SetParameter( GAPROLE_ADVERT_OFF_TIME, sizeof( uint16 ), &gapRole_AdvertOffTime ); //GAPRole_SetParameter( GAPROLE_SCAN_RSP_DATA, sizeof ( scanRspData ), scanRspData ); GAPRole_SetParameter( GAPROLE_ADVERT_DATA, sizeof( advertData ), advertData ); GAPRole_SetParameter( GAPROLE_ADV_EVENT_TYPE, sizeof( uint8 ), &advType ); 保存工程后，进行编译，并通过 CCDebugger 下载程序到开发板中。 Select Project > Clean to clean the project. Select Project > Make to make the project. Select Project > Download and Debug to send the code to the CC2540 Key Fob Select Debug > Go to Run the code on the CC2540 Key Fob. |
|
|
|
|
|
|
|
|
问题解决了 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
只有小组成员才能发言，加入小组>>
576 浏览 0 评论
1636 浏览 0 评论
2070 浏览 0 评论
为啥BQ7693003DBTR芯片在和BQ769X0盒子通讯时收不到信号？
1527 浏览 0 评论
DSP 28027F 开发板 XDS100v2调试探针诊断日志显示了 Error -150 (SC_ERR_FTDI_FAIL)如何解决
1365 浏览 0 评论
AT32F407在USART2 DMA发送数据时，接包接到了要发送的数据，程序还是处于等待传输完成的标识判断中，为什么？
1779浏览 29评论
2806浏览 23评论
请问下tpa3220实际测试引脚功能和官方资料不符，哪位大佬可以帮忙解答下
1737浏览 20评论
请教下关于TAS5825PEVM评估模块原理图中不太明白的地方，寻求答疑
1651浏览 14评论
两个TMP117传感器一个可以正常读取温度值，一个读取的值一直是0，为什么？
1664浏览 13评论
/9 
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 （电路图） 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证：合字B2-20210191
工商网监
湘ICP备2023018690号
4535
评论
淘帖
2765
