以太网入门套件2 DM320004-2 Harmony教程

在我的盒子里，我看到这个演示编辑：那是WiFi，这是以太网（并且有一个SK2演示）



      以下为原文

    On my box I see this demo
edit: that was wifi, this is ethernet ( and has a sk2 demo )

谢谢-有什么指导/教程吗？



      以下为原文

    Hi - Thanks for that - is there any guide / tutorial to go with that?

你可以看看帮助



      以下为原文

    You might look in the help

我已经设法在以太网启动工具箱II演示板上编译和运行（我想）-LeD3闪耀…Microchip HyralV2O04AppTCPIWebSyrVelnVMMMPFS固件PIC32μEth.WebSyVel.X.但是，当我将一***立的笔记本电脑插入到以太网以太网套接字时，它并不OBT。正确的IP地址。文档表明，将发布192.1681.x范围内的IP，但是在笔记本电脑上运行IPCONFIG表明它使用的是169254.149.x和没有网关地址。（导航到MCHPBOADARDE OrMCHPBOARDARC导致超时）。以太网插座本身上的LED（在子板上）在连接到笔记本电脑时会发光和闪烁。有什么想法吗？我希望这是我做错了的事，或者错过了理解。正如前面提到的，我对此非常陌生，所以谢谢你们的支持。



      以下为原文

    I have managed to get this demo to compile and run (I think) on the Ethernet Starter Kit II demo board - LED3 is flashing.
 
..microchipharmonyv2_04appstcpipweb_server_nvm_mpfsfirmwarepic32_eth_web_server.X
 
However when I plug a standalone laptop in to the boards Ethernet socket, it does not obtain the correct IP Address. The documentation suggests that an IP in the range 192.168.1.x would be issued, however running IPCONFIG on the laptop shows it is using 169.254.149.x  and no gateway address. (navigating to mchpboard_e or mchpboard_c results in a timeout). The LEDS on the Ethernet socket itself (on the daughter board) are illuminating and blinking when connected to the laptop.
 
Any ideas? I expect this is something I have done wrong, or miss understood. 
 
As previously mentioned I am very new to this, so thanks for your support.

尝试运行和谐是安装在D上我的盒子。



      以下为原文

    Try running
Harmony is installed on D on my box.

拥有RunTCPIP1发现器，它没有列出任何在微芯片设备下的设备…



      以下为原文

    having run tcpip_discoverer, it has failed to list any devices under Microchip Devices...

你在帮助中看到了吗？



      以下为原文

    Did you see this in the help ?
 
   Attached Image(s)

我看不出在我的文件里，我会试试看是否能让它工作。



      以下为原文

    i cant see that in the document i have, will try and see if i can get that to work

嗯，VCP出现在我运行代码时，但我在终端程序中没有收到任何东西。



      以下为原文

    well the VCP appears when I run the code but i am not reciveing anything in my terminal program. 

试着在终端程序控制台上按下回车键。



      以下为原文

    Try pushing enter in/on the terminal program console.
Restart the Pic board with the terminal program connected.

程序打开时重新启动板的过程会导致VCP暂时消失时崩溃。按下回车键没有任何效果。



      以下为原文

    the process of restarting board with program open causes it to crash when the VCP momentarily disappears. Pushing the enter key has no effect.

这是否是因为我使用板上的调试器运行板——如果它被编程并运行独立，它会运行得更好吗？编辑：似乎没什么区别



      以下为原文

    could this all be becuase I am running the board using the onboard debugger - would it perform better if it were programmed and running standalone?
 
Edit: Doesnt seem to make a difference
 

当我连接它时，ESK2板应该作为DHCP分配给我的笔记本电脑的DHCP地址。或者我需要在网络上引入一个DHCP服务器来管理IP地址吗？



      以下为原文

    Should the ESK2 board be acting as a DHCP assigning teh IP address to my laptop when I connect it. Or do i need to introduce a DHCP server on to the network to manage the ip addresses?

检查你是否已被协调使用



      以下为原文

    Check you have Harmony Configured to use
   Attached Image(s)

是的，设置正确。已经尝试从MHC和清洁建筑恢复，但仍然没有。



      以下为原文

    Yes that is set correctly. Have tried regnerating from MHC and clean building but still nothing

我重新下载了这个项目，重新生成了MHC，并且在终端上已经取得了一些进展，即：TCP/IP堆栈：初始化STARTED SysSype初始化：MPFS2文件系统是安装的TCP/IP堆栈：主机MCHPBOADARDE-E-NBNS的初始化结束-成功接口PIC32 ItEnabdiePIC32 IN IP地址：0.0.0.0PIC32 IN IP地址：192.168100.115＆GT；但是连接到ESK2板上的端口的笔记本电脑仍然没有在该范围内获得IP地址，它当前的地址是169254.14964。（我期待类似192.168100.xxx之类的东西）我相信这部分工作是因为当我停止ESK2板时，笔记本电脑丢失了这个IP地址，然后当我再次启动板时重新获得它。



      以下为原文

    I have re-downloaded the project, regenerated the MHC and have made some progress I now have output at the terminal which is:
 
TCP/IP Stack: Initialization Started
SYS_Initialize: The MPFS2 File System is mounted
TCP/IP Stack: Initialization Ended - success
Interface PIC32INT on host MCHPBOARD_E - NBNS enabled
PIC32INT IP Address: 0.0.0.0
PIC32INT IP Address: 192.168.100.115

>
But the laptop connected to the port on ESK2 board is still not obtaining an IP address in that range, the address it currently has is 169.254.149.64. (I would be expecting something like 192.168.100.xxx) I believe it is partially working as when I stop the ESK2 board the laptop loses this IP address and then regains it when I start the board again.
 

我想你可以试试网络中的DHCP服务器。当连接到笔记本电脑时，你需要SK2在169254.149.x范围（他的自动配置IP）中有一个IP地址。



      以下为原文

    I think you might try a DHCP server in the network.
To connect when plugged into the laptop you would need the SK2 to have an IP address in the 169.254.149.x range ( his auto configure ip ).
With both the laptop and sk2 plugged into a lan with a DHCP at least they should both be in the same are.

是的，我在想…将公布结果



      以下为原文

    yeah i was thinking that... will post back the result
 

好的，我想我知道了。它看起来像是堆栈中的WOLFSSL。当浏览器说不安全时，连接到主板内部网页，无论如何继续…



      以下为原文

    ok, I think I have it.
It looks like wolfssl is enabled in the stack.
to connect to the board internal web page
When the browser says unsafe, proceed anyways....