随机OTA传输FreezeDescriptionHello在迁移过程中存在随机冻结现象

在您的代码中，是否包含任何检查以确保新版本号必须始终高于当前版本号？



     以下为原文
  In your code, did you include any checks to ensure that the new version number must be always be higher than the current one?

你的0.6和0.7 FW的大小分别是多少？



     以下为原文
  And what is the respective size of your 0.6 and 0.7 FW?

尺寸约为155kb。我也使用64KB EEPROM



     以下为原文
  Size is around 15.5Kb. Also I use 64KB EEPROM

我尝试了几次在我的标签板上，来回的版本，但不能重现这个问题。您不使用SIP模块，因此安装应该与我的标签非常相似。您对WSU-UpGeRead OTA.C和WSJUpLoad进行了修改吗？你能试用它们吗？
你也可以把下面的内容添加到Mag文件中吗？
AppthPaTeSeSuxand and Lybs+= thRead and AyMyMgMt. A



     以下为原文
  I tried a few times on my tag boards, back and forth on the versions, but were not able to reproduce the issue. You are not using the sip module and so the setup should be quite similar to my tag. Did you make any modification to ws_upgrade_ota.c and ws_upgrade.c? Can you try using them stock?
 
Can you also add the below to the makefile?
 
APP_PATCHES_AND_LIBS += thread_and_mem_mgmt.a

谢谢，
没有对WSU-UpGeRead OTA.C和WSJ.Excel .C文件进行修改。
也尝试了补丁。
仍然是同样的结果。
在TAG4板上也尝试了“OTA固件升级”的例子。我也经历过同样的问题。



     以下为原文
  Thanks,
There were no modifications made to ws_upgrade_ota.c and ws_upgrade.c files.
Also tried the patch.
Still the same result.
 
Also tried "OTA firmware upgrade " example on TAG4 board. I did experience same issue.
 
 

让我略述一下：
工具：TAG3，基于20702的软件狗，和WsOtaUpgrade.exe上的Win 7 32位PC
1）使用股票OTAYFWY升级应用程序，下载默认的FW，次要版本为1
2）假设BT加密狗连接到标签
3）执行“清洁”遵循“构建”-只有同一个应用程序，次要版本改为2。我也改变了广播的名字
从“Broadcom”到“BroadCon”。
4）将生成的bin文件与WSOTAUPGRADE.EXE一起剪切并保存到文件夹中。
5）在Win控制台中执行（具有管理员权限）：WsOtaUpgrade.exe xxx.bin
6）观察UI出现，并“启动”它
然后我回到“1”然后“2”，我成功了6次。我注意到
在第六次，下载并没有启动，但那是因为
射频链路下降。从蓝牙管理器中删除并添加了我的标签
再次，我可以继续下载。



     以下为原文
  Let me just outline a little:
 
Tools: tag3, 20702 based dongle, and WsOtaUpgrade.exe on win7 32-bit PC
 
1) Using the stock ota_fw_upgrade app, download default FW with minor version as 1
2) Assume bt dongle is connected to tag
3) execute "clean" follow by a "build"-only of the same app, with minor version changed to 2. I also changed the broadcast name
from "Broadcom" to "Broadcon".
4) Cut and save the generated BIN file to a folder, along with WsOtaUpgrade.exe
5) Execute in win console (with admin rights): WsOtaUpgrade.exe xxx.bin
6) Observe a UI appeared, and "Start" it
 
Then I go back to "1" and then "2", and I had success for 6 times. I noted
that in the sixth time, the download did not start, but that's because the
RF link was down. From the Bluetooth Manager, I removed and added my tag
again, and I was able to proceed with the download.

更正：默认的广播名称是“你好”，我把它改成“HELLE”。而不是我上面提到的Broadcom。



     以下为原文
  Correction: The default broadcast name was "Hello" and I changed it to "Helle". And NOT Broadcom as I stated above.

谢谢你的宝贵支持。
发现问题，我们需要禁用“允许计算机关闭这个设备，以节省电力”在“电源管理”的软件狗。
我提到FoLune RE：为什么我打开WsOtaUpgrade.exe时出错？
现在可以执行OTA为8次以上，通过切换版本之间没有毛刺。
我还把补丁添加到make文件中。
再次感谢
哈里克



     以下为原文
  Thanks for your valuable support.
Found  issue; we need to disable "Allow the computer to turn off this device to save power" in ‘Power Management’ for dongle.
I referred follwing Re: Why error occur when I open WsOtaUpgrade.exe?
 
Now can perform OTA for mor ethan 8 times , by switching between version without glitch.
 
I also retaitned the PAtCH in make file.
 
THanks again
haric