完善资料让更多小伙伴认识你，还能领取20积分哦， 立即完善>
3天内不再提示
电子发烧友论坛|
我有WiC1500 PICTHOP PLUS，带有APIC24FJ128GA310PIM的Explorer 16/32，PICTHOP PLUS扩展卡。WiC1500上电（其LED亮起），但来自最新MLA的演示应用程序不起作用；串口显示“无效芯片Rev，预期1003A0，读取0”。如果我拔下WiC1500，行为是相同的，它好像是模块没有被看到。我查看了演示代码，它使用SPI2，但据我所知，PICTHOP PLUS连接到16/32的SPI1引脚，所以我想知道演示是否没有从原来的ExpL更新。奥尔16。有人让这个组合工作了吗？
以上来自于百度翻译 以下为原文 I have the WINC1500 Pictail Plus, the Explorer 16/32 with a PIC24FJ128GA310 PIM, and Pictail Plus expansion card. The WINC1500 powers up (its LED comes on) but the demo app from the latest MLA doesn't work; the serial port shows "Invalid chip rev, expected 1003a0, read 0". If I unplug the WINC1500, the behavior is the same; it's as though the module isn't being seen. I looked into the demo code, and it's using SPI2, but as far as I can tell, the Pictail plus is connecting to the SPI1 pins on the 16/32, so I'm wondering if the demo wasn't updated from the original Explorer 16. Has anyone gotten this combination to work? 
0
|
|
相关推荐
19个回答
|
|
|
这些东西（如使用SPI信道）通常可以在硬件芯片头文件中改变，用于Microchip DeMOS。/ Ruben
以上来自于百度翻译 以下为原文 These things (such as which SPI channel is used) can normally be changed in a hardware settings header file for Microchip demos. /Ruben |
|
|
|
|
|
您好，您找到了用PIC24驱动WC1500的现有SW示例，或者您实际上是如何编写驱动程序的？当做
以上来自于百度翻译 以下为原文 Hi, Did you find an existing SW example for driving WINC1500 with PIC24 or how did you actually write the driver ? Regards |
|
|
|
|
|
|
|
|
|
|
|
我不熟悉你的硬件，但是你的问题和我几年前在一个Explorer 18板上使用RN171 PiT尾的时候非常相似。在抱怨演示固件并用它处理了几个小时之后，我终于发现我放置了PIC。在错误的连接器上的尾板，或者是在正确的连接器上的错误位置。这是我发现的并不是所有的PoTek板都连接在同一个DeV板上的位置。
以上来自于百度翻译 以下为原文 Hi I'm not familiar with your hardware, but your problem is very similar to one I had a few years ago while trying to use an RN171 pictail on top of an Explorer 18 board. After complaining about the demo firmware and messing around with it for a few hours; I ended up discovering that I placed the pictail board on the wrong connector, or was it the wrong position on the right connector.... well something like that. That's how I discovered that not all pictail boards are connected in the same position on the same dev board. Best regards Jorge |
|
|
|
|
|
PICTWEB板上的图片显示了他们希望如何插入到Explorer 16/32，但是代码与图片不匹配。
以上来自于百度翻译 以下为原文 The Pictail board comes with pictures that show exactly how they want it plugged in to the Explorer 16/32, but the code doesn't match the pictures. |
|
|
|
|
|
嗨，你能具体点吗？源项目中哪些与图片不匹配（哪一个）？WC1500 MLA用户指南显示了需要的信号。用欧姆表/示波器，你应该能够检查PICTHER信号是否正确地在PIMAMONE上路由。
以上来自于百度翻译 以下为原文 Hi, Can you please be specific ? What in the source project does not match the pictures (which one) ? The WINC1500 MLA USER guide shows the signals which are needed. With an ohmmeter/oscilloscope you should be able to check if the PICTAIL signals are routed correctly on the PIM Regards |
|
|
|
|
|
JorgeF得到了答案。我看的是董事会的错误图片，所以PICTHER的位置不对。搬家后一切都很顺利。
以上来自于百度翻译 以下为原文 JorgeF had the answer. I was looking at the wrong picture of the board, so the Pictail wasn't in the right position. Everything is working fine after moving the Pictail. |
|
|
|
|
|
在那里，做了，这就是为什么…眨眼：最好的问题
以上来自于百度翻译 以下为原文 Hi Been there, done that, thats why..... wink: Best regards Jorge |
|
|
|
|
|
JT。我注意到，当MyL2011503-06中的WiC1500演示空间不在编译时，在DEMO配置中不使用多个XY XXXXX选项进行注释时，这是工作空间或WiC1500本身的限制。EX.希望能够同时使用U.UPDPclipse和UsIn TCPPL客户端。谢谢。
以上来自于百度翻译 以下为原文 JT. I notice that the WINC1500 demo workspace from MLA 2017-03-06 does not seem to compile when uncommenting multiple #define USING_xxxxxx options within the demo_config.h Is this a limitation of the workspace or the WINC1500 itself.... ex. would like to enable USING_UDP_CLIENT and USING_TCP_CLIENT simultaneously. Thanks. |
|
|
|
|
|
我认为这些演示都是相互独立的。如果要合并功能，则必须编写自己的代码。WiC1500没有任何特殊限制。
以上来自于百度翻译 以下为原文 I think the demos are all independent of each other. If you want to merge functionality, you have to write your own code. The WINC1500 doesn't have any particular limitations. |
|
|
|
|
|
HITCPTCP/IP有很多配置，并且将它们设置成一个连贯的形式是相当复杂的。检查文档，其中一些在不同的文件夹中传播。
以上来自于百度翻译 以下为原文 Hi The TCP/IP has a lot of configurations and its quite complex to set them all in a coherent form. Check the documentation, some of it is spread in different folders. |
|
|
|
|
|
我曾与官方TCP/IP协议栈（2010？），但是使用有线NIC。我能够取消所需的各种协议，并让它们编译和操作W/O操作系统。我会再做一次，但是我没有看到在最新的堆栈中选择WiC1500的支持。只有MRF24。我也看到了旧的MRF24收音机在新的设计中不被推荐的地方。因此，为了解决这个二分法，客户期望为WiC1500组成新的TCP/IP堆栈HAL吗？
以上来自于百度翻译 以下为原文 I've worked with the official TCP/IP Stack before (2010?), but using a wired NIC. I was able to uncomment the various protocols desired and have them compile and function w/o an OS. I would do it again, but I don't see any support for selecting the WINC1500 in the latest stack... only the MRF24. I also see where the older MRF24 radios are not recommended for new designs. So to resolve this dichotomy, is the customer expected to compose the new TCP/IP stack HAL for the WINC1500? |
|
|
|
|
|
嗨，WiC1500是一个原始的Atmel无线模块，它在ASF框架中有很多例子连接到SAMD21/L21微控制器（Atmel Studio），它也支持PIC32的协调。
以上来自于百度翻译 以下为原文 Hi, The WINC1500 being an original ATMEL wireless module it has plenty of examples in ASF framework connected to SAMD21/L21 microcontrollers (ATMEL studio) It is also supported in Harmony with PIC32 Regards |
|
|
|
|
|
好的，谢谢。我在ASF和MLA WiFixWiC1500的DEMO／DEMOOI CONFIG.H文件之间看到这些孤立的演示的一一对应关系。我已经仔细阅读了MLA产品，并设想ASF的实现是同一个协议。我需要在这个时候避免和声和PIC32。ARM或旧DSPIC是Req’d。MIPS不行。所以，对于HTTP服务器W/Page燃烧工具、FTP等有堆栈支持是很好的。这是MLA逐字逐句提供的。但是，我认为一个OS和和谐将是唯一的未来提供的路径。哦，好吧。看SW W/柏树（I.）Broadcom通过ViNTEK。
以上来自于百度翻译 以下为原文 OK thanks. I typ see a one-to-one relation of these isolated demos between the ASF and MLA wifi_winc1500_demo/demo_config.h file. I've perused the MLA offering and imagine the ASF implementation is the same deal. I need to avoid Harmony and PIC32 at this time. ARM or older dsPIC is req'd.. MIPS won't do. So, it'd be nice to have stack support for the HTTP server w/ page burning tools, FTP, etc.. that's offered verbatim from MLA right now. But, I imagine an OS and Harmony will be the only path offered in the future. oh well.. looking at ST w/ Cypress (ie.. Broadcom) via Inventek. |
|
|
|
|
|
|
|
|
|
|
|
演示文稿不被写入以允许多于一个启用。每个演示都有一个由主（）调用的公共应用任务函数，所以如果你一起编译多个，则会有链接错误。将两个应用任务函数的内容结合到自己的应用程序中不太困难。
以上来自于百度翻译 以下为原文 The demos aren't written to allow more than one to be enabled. Each demo has a public ApplicationTask function called by main(), so if you compile more than one together, you'll have linker errors. It shouldn't be too difficult to take the contents of two ApplicationTask functions and combine them into your own app. |
|
|
|
|
|
因此，PIC32 +和声是唯一的处理器+ IDE，它支持新的Atmel WiC1500的UTCP/TCP/IP协议栈的全部功能。我假设不需要额外的硬件NIC。谢谢。
以上来自于百度翻译 以下为原文 RISC. So the PIC32+Harmony is the only processor+IDE that supports the full functionality of the uChip TCP/IP stack with the newly mandated Atmel WINC1500? I assume an additional hardware NIC is not required. Thanks. |
|
|
|
|
|
Hi，WiC1500还支持MLA用于PIC18和16位设备：HTTP://www. McCHIP.COM/MLARGARDS
以上来自于百度翻译 以下为原文 Hi, WINC1500 is also supported in MLA for PIC18 and 16bits devices : http://www.microchip.com/MLA Regards |
|
|
|
|
|
好的，谢谢。我看到了，但它看起来像MLA只提供有限的支持代码，并运行“本地”模式的Wi1500。或者什么…不支持DDNS、MNS、FTP、TFTP、TELNET、WebServer W/MPFS等。您知道PICH32 + WiC1500在Trand下提供了完整的TCP/IP堆栈特性，并允许选择WiC1500作为无线电而不是MRF24无线电吗？我假设它运行在WiC1500的“以太”模式或某事…如果是的，它实际工作吗？谢谢。
以上来自于百度翻译 以下为原文 OK thanks.. I saw that, but it looks like MLA only offers code for limited support and runs the WIN1500 in "native" mode.. or something... ie. no code support for DDNS, mDNS, FTP, TFTP, TELNET, WebServer w/ MPFS, etc... Do you know if PIC32 + WINC1500 under Harmony offers the full TCP/IP stack features and allows to select WINC1500 as the radio instead of an MRF24 radio? I assume it runs the WINC1500 in "ethernet" mode or something.. If so, does it actually work? Thanks. |
|
|
|
|
只有小组成员才能发言，加入小组>>
5231 浏览 9 评论
2026 浏览 8 评论
1950 浏览 10 评论
请问是否能把一个ADC值转换成两个字节用来设置PWM占空比？
3200 浏览 3 评论
请问电源和晶体值之间有什么关系吗？PIC在正常条件下运行4MHz需要多少电压？
2253 浏览 5 评论
771浏览 1评论
659浏览 1评论
有偿咨询，关于MPLAB X IPE烧录PIC32MX所遇到的问题
588浏览 1评论
PIC Kit3出现目标设备ID(00000000)与预期的设备ID(02c20000)不匹配。是什么原因
669浏览 0评论
571浏览 0评论
/6 
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 （电路图） 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证：合字B2-20210191
工商网监
湘ICP备2023018690号
1102
评论
淘帖
636
