完善资料让更多小伙伴认识你，还能领取20积分哦， 立即完善>
3天内不再提示
电子发烧友论坛|
采用5509A 和AIC23实现音频采集，I2C通信配置AIC23，然后通过McBSP0接受数据。并通过DMA传输到内存处理。现在的问题是DMA中断有时可以进去，有时进不去。大多时候是进不去。可以确定AIC23和McBSP0在正常工作，因为DRR寄存器的值在不断更新。但是DMA传完一帧后，进不去中断。查看寄存器，IFR相应位已经置1了，怎么就是进不去ISR呢？下面是我的程序，由CSL例程修改而来，ISR里修改DMA配置，实现pingpong切换。
#include #include #include #include #include "5509.h" //---------Global constants--------- /* Constant defines transfer length */ #define N 128 //---------Global data definition--------- #pragma DATA_SECTION(dst1, "dmaMem") Uint16 dst1[N]; #pragma DATA_SECTION(dst2, "dmaMem") #pragma CODE_SECTION (main, "saram1Section") #pragma CODE_SECTION (taskFxn, "saram1Section") int dst2[N]; DMA_Config myconfig = [ DMA_DMACSDP_RMK( DMA_DMACSDP_DSTBEN_NOBURST, DMA_DMACSDP_DSTPACK_OFF, DMA_DMACSDP_DST_DARAM, DMA_DMACSDP_SRCBEN_NOBURST, DMA_DMACSDP_SRCPACK_OFF, DMA_DMACSDP_SRC_PERIPH, DMA_DMACSDP_DATATYPE_16BIT ), /* DMACSDP */ DMA_DMACCR_RMK( DMA_DMACCR_DSTAMODE_POSTINC, DMA_DMACCR_SRCAMODE_CONST, DMA_DMACCR_ENDPROG_ON, DMA_DMACCR_REPEAT_OFF, DMA_DMACCR_AUTOINIT_ON, DMA_DMACCR_EN_STOP, DMA_DMACCR_PRIO_LOW, DMA_DMACCR_FS_DISABLE, //DMA_DMACCR_FS_ENABLE, DMA_DMACCR_SYNC_REVT0 //DMA_DMACCR_SYNC_NONE ), /* DMACCR */ DMA_DMACICR_RMK( DMA_DMACICR_BLOCKIE_OFF, DMA_DMACICR_LASTIE_OFF, DMA_DMACICR_FRAMEIE_ON, DMA_DMACICR_FIRSTHALFIE_OFF, DMA_DMACICR_DROPIE_OFF, DMA_DMACICR_TIMEOUTIE_OFF ), /* DMACICR */ /* DMACSSAL */ (DMA_AdrPtr)(MCBSP_ADDR(DRR10)), 0, /* DMACSSAU */ (DMA_AdrPtr)&dst1, /* DMACDSAL */ 0, /* DMACDSAU */ N, /* DMACEN */ 1, /* DMACFN */ 0, /* DMACFI */ 0 /* DMACEI */ ]; DMA_Handle myhDma; int i, j; volatile Uint16 transferComplete = FALSE; static int pingpong=0; Uint16 src1AddrHi, src1AddrLo; Uint16 src2AddrHi, src2AddrLo; Uint16 dst1AddrHi, dst1AddrLo; Uint16 dst2AddrHi, dst2AddrLo; Uint32 eventId; Uint16 old_intm; //---------Function prototypes--------- /* Declare Reference for Start of Interrupt Vector Table */ /* This symbol is defined in the vectors.s55 file */ extern VECSTART(void); /* Define a DMA_Handle object */ interrupt void dmaIsr(void); void DMA_init(void); //---------main routine--------- void main(void) [ /* Initializa CSL library - This is REQUIRED !!! */ CSL_init(); EMIF_init(); /* Set IVPD/IPVH to start of interrupt vector table */ IRQ_setVecs((Uint32)(&VECSTART)); /* Initialize source and destination buffers */ for (i = 0; i <= (N - 1); i++) [ dst1 = 0; dst2 = 0; ] /* Call function to effect transfer */ AIC23_init(); DMA_init(); while(1); ] void DMA_init(void) [ /* Open DMA Channel 1 setting registers to their power on defualts */ myhDma = DMA_open(DMA_CHA1, DMA_OPEN_RESET); /* Get Interrupt Event Id associated with this DMA */ eventId = DMA_getEventId(myhDma); src1AddrHi = (Uint16)(((Uint32)(MCBSP_ADDR(DRR10))) >> 15) & 0xFFFFu; src1AddrLo = (Uint16)(((Uint32)(MCBSP_ADDR(DRR10))) << 1) & 0xFFFFu; dst1AddrHi = (Uint16)(((Uint32)(&dst1)) >> 15) & 0xFFFFu; dst1AddrLo = (Uint16)(((Uint32)(&dst1)) << 1) & 0xFFFFu; src2AddrHi = (Uint16)(((Uint32)(MCBSP_ADDR(DRR10))) >> 15) & 0xFFFFu; src2AddrLo = (Uint16)(((Uint32)(MCBSP_ADDR(DRR10))) << 1) & 0xFFFFu; dst2AddrHi = (Uint16)(((Uint32)(&dst2)) >> 15) & 0xFFFFu; dst2AddrLo = (Uint16)(((Uint32)(&dst2)) << 1) & 0xFFFFu; myconfig.dmacssal = (DMA_AdrPtr)src1AddrLo; myconfig.dmacssau = src1AddrHi; myconfig.dmacdsal = (DMA_AdrPtr)dst1AddrLo; myconfig.dmacdsau = dst1AddrHi; /* Write configuration structure values to DMA control registers */ DMA_config(myhDma, &myconfig); //DMA_getConfig(myhDma,&config1); /* Temporarily Disable All Interrupts */ old_intm = IRQ_globalDisable(); /* Clear any pending interrupts for DMA in IFR */ IRQ_clear(eventId); /* Enable the DMA interrupt in IER register */ IRQ_enable(eventId); /* Set Interrupt Vector Start Location */ IRQ_setVecs((Uint32)(0x10000)); /* Place ISR address in associated vector location */ IRQ_plug(eventId, &dmaIsr); /* Enable all maskable interrupts */ IRQ_globalEnable(); IRQ_globalRestore(old_intm); /* Enable DMA channel to begin transfer */ DMA_start(myhDma); /* Wait for programmation bit, ENDPROG == 0, to make sure that device's */ /* configuration register set has already been copied to working set */ while (DMA_FGETH(myhDma,DMACCR,ENDPROG)) ; /* Write next set of configuration values to the DMA control regs */ /* for next transfer */ DMA_RSETH(myhDma,DMACSSAU,src2AddrHi); DMA_RSETH(myhDma,DMACSSAL,src2AddrLo); DMA_RSETH(myhDma,DMACDSAU,dst2AddrHi); DMA_RSETH(myhDma,DMACDSAL,dst2AddrLo); DMA_RSETH(myhDma,DMACEN, N); DMA_RSETH(myhDma,DMACFN, 1); /* Set programmation bit to 1, ENDPROG = 1) */ DMA_FSETH(myhDma,DMACCR,ENDPROG,1); /* Restore GLobal Interrupt Enable to Previous Setting */ //IRQ_globalRestore(old_intm); ] /* DMA Interrupt Service Routine */ interrupt void dmaIsr(void) [ IRQ_clear(eventId); old_intm = IRQ_globalDisable(); DMA_FSETH(myhDma,DMACSR,FRAME,0); if(pingpong) [ while (DMA_FGETH(myhDma,DMACCR,ENDPROG)); DMA_RSETH(myhDma,DMACSSAU,src2AddrHi); DMA_RSETH(myhDma,DMACSSAL,src2AddrLo); DMA_RSETH(myhDma,DMACDSAU,dst2AddrHi); DMA_RSETH(myhDma,DMACDSAL,dst2AddrLo); DMA_RSETH(myhDma,DMACEN, N); DMA_RSETH(myhDma,DMACFN, 1); DMA_FSETH(myhDma,DMACCR,ENDPROG,1); ] else [ while (DMA_FGETH(myhDma,DMACCR,ENDPROG)); DMA_RSETH(myhDma,DMACSSAU,src1AddrHi); DMA_RSETH(myhDma,DMACSSAL,src1AddrLo); DMA_RSETH(myhDma,DMACDSAU,dst1AddrHi); DMA_RSETH(myhDma,DMACDSAL,dst1AddrLo); DMA_RSETH(myhDma,DMACEN, N); DMA_RSETH(myhDma,DMACFN, 1); DMA_FSETH(myhDma,DMACCR,ENDPROG,1); ] pingpong=!pingpong; IRQ_globalRestore(old_intm); IRQ_enable(eventId); ] :mad: 我的中断向量表文件：vectors_dma2.s55 * * Copyright (C) 2003 Texas Instruments Incorporated * All Rights Reserved * * *---------vectors_dma2.s55--------- * * Assembly file to set up interrupt vector table * .sect ".vectors" *------------------------------------------------------------------------------ * Global symbols defined here and exported out of this file *------------------------------------------------------------------------------ .global _VECSTART *------------------------------------------------------------------------------ * Global symbols referenced in this file but defined somewhere else. * Remember that your interrupt service routines need to be referenced here. *------------------------------------------------------------------------------ .ref _c_int00 .def nmi, int0, int1, int2, int3, int4, int5, int6 .def int7, int8, int9, int10, int11, int12, int13 .def int14, int15, int16, int17, int18, int19, int20 .def int21, int22, int23, int24, int25, int26, int27 .def int28, int29 _VECSTART: .ivec _c_int00,c54x_stk nmi .ivec no_isr nop_16 int0 .ivec no_isr nop_16 int1 .ivec no_isr nop_16 int2 .ivec no_isr nop_16 int3 .ivec no_isr nop_16 int4 .ivec no_isr nop_16 int5 .ivec no_isr nop_16 int6 .ivec no_isr nop_16 int7 .ivec no_isr nop_16 int8 .ivec no_isr nop_16 int9 .ivec no_isr nop_16 int10 .ivec no_isr nop_16 int11 .ivec no_isr nop_16 int12 .ivec no_isr nop_16 int13 .ivec no_isr nop_16 int14 .ivec no_isr nop_16 int15 .ivec no_isr nop_16 int16 .ivec no_isr nop_16 int17 .ivec no_isr nop_16 int18 .ivec no_isr nop_16 int19 .ivec no_isr nop_16 int20 .ivec no_isr nop_16 int21 .ivec no_isr nop_16 int22 .ivec no_isr nop_16 int23 .ivec no_isr nop_16 int24 .ivec no_isr nop_16 int25 .ivec no_isr nop_16 int26 .ivec no_isr nop_16 int27 .ivec no_isr nop_16 int28 .ivec no_isr nop_16 int29 .ivec no_isr nop_16 *------------------------------------------------------------------------------ * This is a dummy interrupt service routine used to initialize the IST. *------------------------------------------------------------------------------ .text .def no_isr no_isr: b #no_isr *------------------------------------------------------------------------------ 没有人遇到类似问题啊？ 我将配置里的控制寄存器CCR的repeat值改为1，也就是采用自动重复加载配置的模式，那么数据传输没有任何问题。 现在想在传输一帧后发送DMA中断给CPU，CPU进行处理。同时要在ISR里修改配置的目的地址。就是进不去中断。 CCS环境3.3 请老师救急啊 
0
|
|
相关推荐
3 个讨论
|
|
|
如果你用repeat 模式正常，说明McBSP配置是正确的了，但是DMA配置不对。
不确认你是否注意到：McBSP的传输是连续不断的，如果在DMA中断里配置下一个DMA的参数，那么在配置好之前这一段时间的数据如何接收呢？ 在当前DMA启动后，即可配置下一个DMA的参数，这样在当前DMA传完后，自动用下一组参数开始传递，这时才来得及在DMA的中断里配置下一个DMA参数，再看一下DMA配置，你应该可以明白这一点的。 http://processors.wiki.ti.com/index.php/Main_Page Think Over Before Asking. http://www.catb.org/~esr/faqs/smart-questions.html#goal |
|
|
|
|
|
|
|
lifei639156 发表于 2018-7-31 06:48 IRQ_plug(eventId, &dmaIsr); /* Enable all maskable interrupts */ IRQ_globalEnable(); IRQ_globalRestore(old_intm); /* Enable DMA channel to begin transfer */ DMA_start(myhDma); /* Wait for programmation bit, ENDPROG == 0, to make sure that device's */ 请问老师是不是这个中断值重载的太早了 |
|
|
|
|
|
|
|
只有小组成员才能发言，加入小组>>
549 浏览 0 评论
1613 浏览 0 评论
2047 浏览 0 评论
为啥BQ7693003DBTR芯片在和BQ769X0盒子通讯时收不到信号？
1513 浏览 0 评论
DSP 28027F 开发板 XDS100v2调试探针诊断日志显示了 Error -150 (SC_ERR_FTDI_FAIL)如何解决
1337 浏览 0 评论
AT32F407在USART2 DMA发送数据时，接包接到了要发送的数据，程序还是处于等待传输完成的标识判断中，为什么？
1756浏览 29评论
2781浏览 23评论
请问下tpa3220实际测试引脚功能和官方资料不符，哪位大佬可以帮忙解答下
1723浏览 20评论
请教下关于TAS5825PEVM评估模块原理图中不太明白的地方，寻求答疑
1634浏览 14评论
两个TMP117传感器一个可以正常读取温度值，一个读取的值一直是0，为什么？
1645浏览 13评论
/9 
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 （电路图） 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证：合字B2-20210191
工商网监
湘ICP备2023018690号
2839
评论
淘帖
0
2287
