[问答]

IWDG无法写入预分频器和重载寄存器的原因？

问答对人有帮助，内容完整，我也想知道答案 0 我正在尝试检查 Nucleo-L4R5ZI 板上的 IWDG 功能。参考可用于 NUCLEO-L496ZG 的示例代码，我为 L4R5ZI nucleo 创建了新项目。我试图在调试模式下逐步进行。当调试器在 HAL_IWDG_Init(&hiwdg) 内部时，它能够使用 __HAL_IWDG_START(hiwdg) 成功启用 IWDG；但是什么时候进入 IWDG_ENABLE_WRITE_ACCESS(hiwdg); 调试器进入系统内存。我通过暂停调试确认了这一点，它停在 0x1FFFxxxx 地址。同时，LD3 LED 发光。在我控制 LD3 的代码中没有任何地方。怎么了？请帮助。代码如下： /* Includes ------------------------------------------------------------------/ #include "main.h" / Private includes ----------------------------------------------------------/ / USER CODE BEGIN Includes / / USER CODE END Includes / / Private typedef -----------------------------------------------------------/ / USER CODE BEGIN PTD / / USER CODE END PTD / / Private define ------------------------------------------------------------/ / USER CODE BEGIN PD / / USER CODE END PD / / Private macro -------------------------------------------------------------/ / USER CODE BEGIN PM / / USER CODE END PM / / Private variables ---------------------------------------------------------/ IWDG_HandleTypeDef hiwdg; UART_HandleTypeDef hlpuart1; UART_HandleTypeDef huart1; UART_HandleTypeDef huart3; PCD_HandleTypeDef hpcd_USB_OTG_FS; / USER CODE BEGIN PV / / USER CODE END PV / / Private function prototypes -----------------------------------------------/ void SystemClock_Config(void); static void MX_GPIO_Init(void); static void MX_LPUART1_UART_Init(void); static void MX_USART3_UART_Init(void); static void MX_USB_OTG_FS_PCD_Init(void); static void MX_IWDG_Init(void); / USER CODE BEGIN PFP / / USER CODE END PFP / / Private user code ---------------------------------------------------------/ / USER CODE BEGIN 0 / / USER CODE END 0 / /* * @brief The application entry point. * @retval int / int main(void) { / USER CODE BEGIN 1 / / USER CODE END 1 / / MCU Configuration--------------------------------------------------------/ / Reset of all peripherals, Initializes the Flash interface and the Systick. / HAL_Init(); / USER CODE BEGIN Init / / USER CODE END Init / / Configure the system clock / SystemClock_Config(); / USER CODE BEGIN SysInit / / USER CODE END SysInit / / Initialize all configured peripherals / MX_GPIO_Init(); MX_LPUART1_UART_Init(); MX_USART3_UART_Init(); MX_USB_OTG_FS_PCD_Init(); MX_IWDG_Init(); / USER CODE BEGIN 2 / if(HAL_IWDG_Init(&hiwdg) != HAL_OK) { / Initialization Error / Error_Handler(); } / USER CODE END 2 / / Infinite loop / / USER CODE BEGIN WHILE / while (1) { / USER CODE END WHILE / / Refresh IWDG: reload counter / if(HAL_IWDG_Refresh(&hiwdg) != HAL_OK) { / Refresh Error / Error_Handler(); } HAL_GPIO_WritePin(GPIOA, GPIO_PIN_0, GPIO_PIN_RESET); while(1); / USER CODE BEGIN 3 / } / USER CODE END 3 / } /* * @brief IWDG Initialization Function * @param None * @retval None / static void MX_IWDG_Init(void) { / USER CODE BEGIN IWDG_Init 0 / / USER CODE END IWDG_Init 0 / / USER CODE BEGIN IWDG_Init 1 / / USER CODE END IWDG_Init 1 / hiwdg.Instance = IWDG; hiwdg.Init.Prescaler = IWDG_PRESCALER_32; hiwdg.Init.Window = IWDG_WINDOW_DISABLE; hiwdg.Init.Reload = 4095; if (HAL_IWDG_Init(&hiwdg) != HAL_OK) { Error_Handler(); } / USER CODE BEGIN IWDG_Init 2 / / USER CODE END IWDG_Init 2 / } /* * @brief GPIO Initialization Function * @param None * @retval None / static void MX_GPIO_Init(void) { GPIO_InitTypeDef GPIO_InitStruct = {0}; / GPIO Ports Clock Enable / __HAL_RCC_GPIOC_CLK_ENABLE(); __HAL_RCC_GPIOH_CLK_ENABLE(); __HAL_RCC_GPIOA_CLK_ENABLE(); __HAL_RCC_GPIOB_CLK_ENABLE(); __HAL_RCC_GPIOD_CLK_ENABLE(); __HAL_RCC_GPIOG_CLK_ENABLE(); HAL_PWREx_EnableVddIO2(); /Configure GPIO pin Output Level / HAL_GPIO_WritePin(GPIOA, GPIO_PIN_0, GPIO_PIN_SET); /Configure GPIO pin Output Level / HAL_GPIO_WritePin(GPIOB, LD3_Pin\|LD2_Pin, GPIO_PIN_RESET); /Configure GPIO pin Output Level / HAL_GPIO_WritePin(USB_PowerSwitchOn_GPIO_Port, USB_PowerSwitchOn_Pin, GPIO_PIN_RESET); /Configure GPIO pin : B1_Pin / GPIO_InitStruct.Pin = B1_Pin; GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING; GPIO_InitStruct.Pull = GPIO_NOPULL; HAL_GPIO_Init(B1_GPIO_Port, &GPIO_InitStruct); /Configure GPIO pin : PA0 / GPIO_InitStruct.Pin = GPIO_PIN_0; GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; GPIO_InitStruct.Pull = GPIO_PULLUP; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); /Configure GPIO pins : LD3_Pin LD2_Pin / GPIO_InitStruct.Pin = LD3_Pin\|LD2_Pin; GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); /Configure GPIO pin : USB_PowerSwitchOn_Pin / GPIO_InitStruct.Pin = USB_PowerSwitchOn_Pin; GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; HAL_GPIO_Init(USB_PowerSwitchOn_GPIO_Port, &GPIO_InitStruct); /Configure GPIO pin : USB_OverCurrent_Pin / GPIO_InitStruct.Pin = USB_OverCurrent_Pin; GPIO_InitStruct.Mode = GPIO_MODE_INPUT; GPIO_InitStruct.Pull = GPIO_NOPULL; HAL_GPIO_Init(USB_OverCurrent_GPIO_Port, &GPIO_InitStruct); } / USER CODE BEGIN 4 / / USER CODE END 4 / /* * @brief This function is executed in case of error occurrence. * @retval None / void Error_Handler(void) { / USER CODE BEGIN Error_Handler_Debug / / User can add his own implementation to report the HAL error return state / / USER CODE END Error_Handler_Debug / } #ifdef USE_FULL_ASSERT /* * @brief Reports the name of the source file and the source line number * where the assert_param error has occurred. * @param file: pointer to the source file name * @param line: assert_param error line source number * @retval None / void assert_failed(uint8_t file, uint32_t line) { /* USER CODE BEGIN 6 / / User can add his own implementation to report the file name and line number, tex: printf("Wrong parameters value: file %s on line %drn", file, line) / / USER CODE END 6 / } #endif / USE_FULL_ASSERT / /********************* (C) COPYRIGHT STMicroelectronics *END OF FILE**/ 0
2023-1-29 06:35:11　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × wang21cj 该类别下有 47 个回答。邀请回答 chm5 该类别下有 44 个回答。邀请回答新星之火12138 该类别下有 42 个回答。邀请回答 hgimtk 该类别下有 36 个回答。邀请回答 HengDu 该类别下有 31 个回答。邀请回答 hwp0415229 该类别下有 30 个回答。邀请回答可口可甜该类别下有 30 个回答。邀请回答麻酱该类别下有 28 个回答。邀请回答 andyfly7 该类别下有 28 个回答。邀请回答 jghgfdssas 该类别下有 28 个回答。邀请回答 jiangwenwen 该类别下有 28 个回答。邀请回答 kingnet6688 该类别下有 28 个回答。邀请回答 ldliu 该类别下有 27 个回答。邀请回答成长的小师弟该类别下有 27 个回答。邀请回答云汉007 该类别下有 27 个回答。邀请回答颜刚YanG 该类别下有 27 个回答。邀请回答柱子图宁该类别下有 27 个回答。邀请回答 bluepink 该类别下有 27 个回答。邀请回答法规处发该类别下有 27 个回答。邀请回答哼小曲该类别下有 26 个回答。邀请回答举报李春梅相关推荐 • STM32L452中的IWDG无论预分频器寄存器的值如何 420 • 请问ATtiny13系统时钟如何通过设置时钟预分频寄存器CLKPR来分频？ 1311 • 请问RTC预分频器余数寄存该怎么操作？ 2052 • STM32独立看门狗（IWDG）有哪些相关的寄存器 962 • 请问PWM预分频器、分频器和定时器的分辨率是多少？ 2233 • stm32的定时器1是怎样作为定时器2的预分频器的 1841 • 独立看门狗IWDG的主要寄存器有哪些 1590 • 为什么更改WWDOG预分频器会停止看门狗倒计时？ 506 • 输入捕获预分频器都无法按预期工作的原因？怎么解决？ 396 • 为什么CubeMX中没有预分频器设置？ 507 1个回答

答案对人有帮助，有参考价值 0 我发现了问题。我在调试模式下测试。这就是原因。数据表说“当设备进入调试模式（内核暂停）时，IWDG 计数器继续正常工作或停止，具体取决于 DBGMCU 冻结寄存器中相应位的配置。” 因此，当我退出调试模式并进行电源回收时，我可以看到预期的行为。

2023-1-29 11:52:17 评论举报凌流浪