[问答]

在CubeIDE 1.9.0中使用stm32f429i-disco设备工作出错是何原因及如何修复呢？

问答对人有帮助，内容完整，我也想知道答案 0 你好。我在 CubeIDE 1.9.0 中使用 STM32f429i-disco 设备工作。问题出现在固件和调试方面。我做了一个简单的例子来检查。在调试期间，在执行 HAL_Delay（第 95 行）时注意到奇怪的行为。在此行执行 Step Over 时，Debug Current Instruction Pointer 保持在同一行。如果您在此行上放置一个断点并恢复，则 LED 会在每次迭代后重置为初始状态（关闭），尽管它们应该每 250 毫秒更改一次状态。以前，我在这个板上使用引导加载程序。我还注意到，在微控制器内存中没有固件的情况下通电时，用户 USB LED 会亮起。Keil 面临与上述相同的问题。请告诉我，这可能是电路板机械损坏的结果，还是其他原因以及如何修复？ /* USER CODE BEGIN Header / /* ****************************************************************************** * @file : main.c * @brief : Main program body ****************************************************************************** * @attention * * Copyright (c) 2022 STMicroelectronics. * All rights reserved. * * This software is licensed under terms that can be found in the LICENSE file * in the root directory of this software component. * If no LICENSE file comes with this software, it is provided AS-IS. * ****************************************************************************** / / USER CODE END Header / / Includes ------------------------------------------------------------------/ #include "main.h" / Private includes ----------------------------------------------------------/ / USER CODE BEGIN Includes / / USER CODE END Includes / / Private typedef -----------------------------------------------------------/ / USER CODE BEGIN PTD / / USER CODE END PTD / / Private define ------------------------------------------------------------/ / USER CODE BEGIN PD / / USER CODE END PD / / Private macro -------------------------------------------------------------/ / USER CODE BEGIN PM / / USER CODE END PM / / Private variables ---------------------------------------------------------/ / USER CODE BEGIN PV / / USER CODE END PV / / Private function prototypes -----------------------------------------------/ void SystemClock_Config(void); static void MX_GPIO_Init(void); / USER CODE BEGIN PFP / / USER CODE END PFP / / Private user code ---------------------------------------------------------/ / USER CODE BEGIN 0 / / USER CODE END 0 / /* * @brief The application entry point. * @retval int / int main(void) { / USER CODE BEGIN 1 / / USER CODE END 1 / / MCU Configuration--------------------------------------------------------/ / Reset of all peripherals, Initializes the Flash interface and the Systick. / HAL_Init(); / USER CODE BEGIN Init / / USER CODE END Init / / Configure the system clock / SystemClock_Config(); / USER CODE BEGIN SysInit / / USER CODE END SysInit / / Initialize all configured peripherals / MX_GPIO_Init(); / USER CODE BEGIN 2 / / USER CODE END 2 / / Infinite loop / / USER CODE BEGIN WHILE / while (1) { HAL_Delay(250); HAL_GPIO_TogglePin(GPIOG, LED_1_Pin); HAL_GPIO_TogglePin(GPIOG, LED_2_Pin); / USER CODE END WHILE / / USER CODE BEGIN 3 / } / USER CODE END 3 / } /* * @brief System Clock Configuration * @retval None / void SystemClock_Config(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; /* Configure the main internal regulator output voltage / __HAL_RCC_PWR_CLK_ENABLE(); __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); /* Initializes the RCC Oscillators according to the specified parameters * in the RCC_OscInitTypeDef structure. / RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI; RCC_OscInitStruct.HSIState = RCC_HSI_ON; RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT; RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI; RCC_OscInitStruct.PLL.PLLM = 8; RCC_OscInitStruct.PLL.PLLN = 180; RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; RCC_OscInitStruct.PLL.PLLQ = 4; if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { Error_Handler(); } /* Activate the Over-Drive mode / if (HAL_PWREx_EnableOverDrive() != HAL_OK) { Error_Handler(); } /* Initializes the CPU, AHB and APB buses clocks / RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK\|RCC_CLOCKTYPE_SYSCLK \|RCC_CLOCKTYPE_PCLK1\|RCC_CLOCKTYPE_PCLK2; RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) { Error_Handler(); } } /* * @brief GPIO Initialization Function * @param None * @retval None / static void MX_GPIO_Init(void) { GPIO_InitTypeDef GPIO_InitStruct = {0}; / GPIO Ports Clock Enable / __HAL_RCC_GPIOH_CLK_ENABLE(); __HAL_RCC_GPIOG_CLK_ENABLE(); /Configure GPIO pin Output Level / HAL_GPIO_WritePin(GPIOG, LED_2_Pin\|LED_1_Pin, GPIO_PIN_RESET); /Configure GPIO pins : LED_2_Pin LED_1_Pin / GPIO_InitStruct.Pin = LED_2_Pin\|LED_1_Pin; GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; HAL_GPIO_Init(GPIOG, &GPIO_InitStruct); } / USER CODE BEGIN 4 / / USER CODE END 4 / /* * @brief This function is executed in case of error occurrence. * @retval None / void Error_Handler(void) { / USER CODE BEGIN Error_Handler_Debug / / User can add his own implementation to report the HAL error return state / __disable_irq(); while (1) { } / USER CODE END Error_Handler_Debug / } #ifdef USE_FULL_ASSERT /* * @brief Reports the name of the source file and the source line number * where the assert_param error has occurred. * @param file: pointer to the source file name * @param line: assert_param error line source number * @retval None / void assert_failed(uint8_t file, uint32_t line) { /* USER CODE BEGIN 6 / / User can add his own implementation to report the file name and line number, ex: printf("Wrong parameters value: file %s on line %drn", file, line) / / USER CODE END 6 / } #endif / USE_FULL_ASSERT */ 0
2022-12-12 08:33:39　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × wang21cj 该类别下有 44 个回答。邀请回答新星之火12138 该类别下有 41 个回答。邀请回答 chm5 该类别下有 39 个回答。邀请回答 hgimtk 该类别下有 33 个回答。邀请回答 HengDu 该类别下有 30 个回答。邀请回答 hwp0415229 该类别下有 28 个回答。邀请回答 jghgfdssas 该类别下有 28 个回答。邀请回答 kingnet6688 该类别下有 26 个回答。邀请回答颜刚YanG 该类别下有 26 个回答。邀请回答可口可甜该类别下有 26 个回答。邀请回答柱子图宁该类别下有 25 个回答。邀请回答 kingnet9999 该类别下有 25 个回答。邀请回答 jenny042 该类别下有 25 个回答。邀请回答 andyfly7 该类别下有 25 个回答。邀请回答麻酱该类别下有 25 个回答。邀请回答 zyh34997 该类别下有 25 个回答。邀请回答哼小曲该类别下有 24 个回答。邀请回答云汉007 该类别下有 24 个回答。邀请回答 ggfvxv 该类别下有 24 个回答。邀请回答 heks 该类别下有 24 个回答。邀请回答举报安立路相关推荐 • 有关STM32F429I-DISCO的基本知识汇总 1192 • 请问哪里有这个开发板STM32F429I-DISCO的屏卖？ 2272 • 怎样去设计一种STM32F429i-DISCO的液晶模块呢 1879 • 如何明确地将TouchGFX应用程序集成到STM32CubeIDE中？ 211 • 求助，使用TouchGFX时如何创建多个STM32CubeIDE工程？ 379 • 如何在CubeIDE中打开和使用TouchGFX项目呢 358 • 怎样去使用STM32F429I-Disco1板上的5V容限引脚呢？ 299 • STM32H7上的DMA选项在STM32CubeIDE中消失咋办呢 300 • 可以在STM32CubeIDE中打开并构建TouchGFX项目吗？ 227 • 怎样去解决在STM32CubeIDE1.9.0版本导入项目失败的问题呢 436 1个回答