[问答]

通过UART4获得输出，为什么无法输入任何内容？

214

问答对人有帮助，内容完整，我也想知道答案 0 我正在使用 STM32mp157c-ev1 开发板。我使用了 digi-key 的这个指南来安装 debian（ Debian: Getting Started with the STM32MP157 )，除了它说 stm32mp157c-dk2 的部分，我用适当的“-ev1”后缀替换了它。我也遵循了关于 Discovery kit 2 板的相同指南，并且它没有问题。问题是，当我尝试通过 minicom 通过 UART4 从板上启动时，虽然一切看起来都在正确启动（减去这个错误：错误无法将桥 /soc/dsi@5a000000 连接到编码器 DPI-31：- 517). 这意味着它向我显示登录提示，但我无法输入任何内容。我尝试将键盘连接到板上，但它似乎仍然没有收到任何输入。尝试通过 st-link 连接甚至更奇怪，因为它显示我根本没有输出（即使 CubeIDE 能够通过调试器检测到 ST-LINK S/N）。我什至从 CubeIDE 升级了 ST-LINK。输出： NOTICE: CPU: STM32MP157CAA Rev.B NOTICE: Model: STMicroelectronics STM32MP157C eval daughter on eval mother NOTICE: Board: MB1263 Var1.0 Rev.C-02 NOTICE: BL2: v2.5(release):v2.5 NOTICE: BL2: Built : 16:14:51, Oct 10 2022 NOTICE: BL2: Booting BL32 NOTICE: SP_MIN: v2.5(release):v2.5 NOTICE: SP_MIN: Built : 16:14:56, Oct 10 2022 U-Boot 2022.10 (Oct 10 2022 - 16:10:15 +0300) CPU: STM32MP157CAA Rev.B Model: STMicroelectronics STM32MP157C eval daughter on eval mother Board: stm32mp1 in trusted - stm32image mode (st,stm32mp157c-ev1) Board: MB1263 Var1.0 Rev.C-02 DRAM: 1 GiB Clocks: - MPU : 650 MHz - MCU : 208.878 MHz - AXI : 266.500 MHz - PER : 24 MHz - DDR : 533 MHz stmfx stmfx@42: STMFX id: 0x7b, fw version: 3.03 Core: 285 devices, 43 uclasses, devicetree: board WDT: Started watchdog@5a002000 with servicing (32s timeout) NAND: 1024 MiB MMC: STM32 SD/MMC: 0, STM32 SD/MMC: 1 Loading Environment from MMC... OK In: serial Out: serial Err: serial invalid MAC address 0 in OTP 00:00:00:00:00:00 Net: Error: ethernet@5800a000 address not set. No ethernet found. Hit any key to stop autoboot: 0 Boot over mmc0! switch to partitions #0, OK mmc0 is current device Scanning mmc 0:4... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 1: Linux 5.15.65-armv7-lpae-x30 Retrieving file: /boot/vmlinuz-5.15.65-armv7-lpae-x30 append: console=ttySTM0,115200 root=/dev/mmcblk0p4 ro rootfstype=ext4 rootwait Retrieving file: /boot/dtbs/5.15.65-armv7-lpae-x30/stm32mp157c-ev1.dtb Kernel image @ 0xc2000000 [ 0x000000 - 0xb93200 ] ## Flattened Device Tree blob at c4000000 Booting using the fdt blob at 0xc4000000 Loading Device Tree to cffe8000, end cffff920 ... OK optee optee: OP-TEE api uid mismatch optee optee: OP-TEE api uid mismatch Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 . . . . . [ OK ] Started WPA supplicant. [ OK ] Started Authorization Manager. Starting Modem Manager... [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Manager. [ OK ] Reached target Network. Starting A high performanc… and a reverse proxy server... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... [ OK ] Started User Login Manage [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Modem Manager. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started A high performance…er and a reverse proxy server. [ OK ] Started Hostname Service. Starting Network Manager Script Dispatcher Service... [ OK ] Started Network Manager Script Dispatcher Service. [ OK ] Created slice system-systemdx2dbacklight.slice. [ 32.935276] stm32-rproc 10000000.m4: wdg irq registered [ 32.941476] remoteproc remoteproc0: m4 is available [ 32.958564] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 Starting Load/Save Screen …f backlight:panel-backlight... [ OK ] Finished Load/Save Screen … of backlight:panel-backlight. [ 33.177508] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 [ OK ] Found device /dev/ttySTM0. [ OK ] Started Serial Getty on ttySTM0. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. [ 33.651687] dwc2 49000000.usb-otg: supply vusb_d not found, using dummy regulator [ 33.684404] dwc2 49000000.usb-otg: supply vusb_a not found, using dummy regulator [ 33.826043] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM [ 33.860157] dwc2 49000000.usb-otg: DWC OTG Controller [ 33.870075] dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 2 [ 33.906169] dwc2 49000000.usb-otg: irq 51, io mem 0x49000000 [ 33.926645] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15 [ 33.953543] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 33.969347] usb usb2: Product: DWC OTG Controller [ 33.982103] usb usb2: Manufacturer: Linux 5.15.65-armv7-lpae-x30 dwc2_hsotg [ 33.996095] usb usb2: SerialNumber: 49000000.usb-otg [ 34.007656] hub 2-0:1.0: USB hub found [ 34.018201] hub 2-0:1.0: 1 port detected [ 34.040081] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 [ 34.059224] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 Debian GNU/Linux 11 arm ttySTM0 default username:password is [debian:temppwd] arm login: [ 36.392709] stm32-dwmac 5800a000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E Gigabit Ethernet] (irq=POLL) [ 36.411191] stm32-dwmac 5800a000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 36.425124] dwmac4: Master AXI performs any burst length [ 36.434808] stm32-dwmac 5800a000.ethernet eth0: No Safety Features support found [ 36.658599] stm32-dwmac 5800a000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 36.670724] stm32-dwmac 5800a000.ethernet eth0: registered PTP clock [ 36.676992] stm32-dwmac 5800a000.ethernet eth0: configuring for phy/rgmii-id link mode [ 40.780334] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 40.787539] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 41.015597] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 [ 41.044836] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 [ 43.278419] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 [ 43.353221] spi-nor spi0.0: mx66l51235f (65536 Kbytes) [ 43.386430] input: pmic_onkey as /devices/platform/soc/5c002000.i2c/i2c-2/2-0033/5c002000.i2c:stpmic@33:onkey/input/input0 [ 43.425684] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 [ 43.503909] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 [ 43.538977] spi-nor spi0.1: mx66l51235f (65536 Kbytes) [ 43.615948] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 [ 44.201364] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/platform/soc/5800d000.usb/usb1/1-1/1 [ 44.292375] hid-generic 0003:045E:0040.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with 0 [ 44.343737] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517 [ 44.379708] input: DELL Dell USB Entry Keyboard as /devices/platform/soc/5800d000.usb/usb1/1-1/1-1.3/1-1.3:1.0/0003:413C:2 [ 44.479567] hid-generic 0003:413C:2107.0002: input,hidraw1: USB HID v1.11 Keyboard [DELL Dell USB Entry Keyboard] on usb-0 [ 44.498558] [drm:drm_bridge_attach] ERROR failed to attach bridge /soc/dsi@5a000000 to encoder DPI-31: -517' 0
2022-12-5 07:22:34　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × wang21cj 该类别下有 47 个回答。邀请回答 chm5 该类别下有 44 个回答。邀请回答新星之火12138 该类别下有 42 个回答。邀请回答 hgimtk 该类别下有 36 个回答。邀请回答 HengDu 该类别下有 31 个回答。邀请回答 hwp0415229 该类别下有 30 个回答。邀请回答可口可甜该类别下有 30 个回答。邀请回答 kingnet6688 该类别下有 28 个回答。邀请回答麻酱该类别下有 28 个回答。邀请回答 andyfly7 该类别下有 28 个回答。邀请回答 jghgfdssas 该类别下有 28 个回答。邀请回答 jiangwenwen 该类别下有 28 个回答。邀请回答 ldliu 该类别下有 27 个回答。邀请回答成长的小师弟该类别下有 27 个回答。邀请回答云汉007 该类别下有 27 个回答。邀请回答颜刚YanG 该类别下有 27 个回答。邀请回答柱子图宁该类别下有 27 个回答。邀请回答 bluepink 该类别下有 27 个回答。邀请回答法规处发该类别下有 27 个回答。邀请回答哼小曲该类别下有 26 个回答。邀请回答举报哥儿相关推荐 • 请问UART4可以通过ROM监视器对eMMC进行编程吗 301 • dm8147的uart4读问题 1484 • 请问NUC029SDE芯片有UART4/5吗？ 296 • STM32F10X UART4 + DMA的代码分享 1012 • 请问NUC029SDE芯片有UART4/5吗？ 306 • 8148 LINUX下打开UART4 1885 • stm32添加串口UART4出错怎么解决？ 1438 • 如何通过UART4接口让FSBL在STM32MP151上运行呢？ 470 • STM32F107的UART4无法进入接收中断 3689 • uart4与内部flash操作出现冲突 2644 1个回答

答案对人有帮助，有参考价值 0 这是 minicom 中的一个不幸的默认配置。按 Ctrl+A 和 O 转到 mincom 的配置 -> 串行端口设置并禁用硬件流控制。这解决了 UART 的仅输出问题，但我仍然没有使用 ST-LINK 获得任何输出。

2022-12-5 10:35:51 评论举报王涛