PWM TIM9上RTT仿真寄存器竟然不变化是何原因

TIM1到TIM8 PWM都调通了 仿真TIM寄存器是会变化的
TIM9仿真不行 如图
用keil TIM9也调通了 就是上RTT不行
最主要问题是仿真寄存器竟然不变化 给点想法

static rt_err_t stm32_hw_pwm_init(struct stm32_pwm *device)
{
rt_err_t result = RT_EOK;
TIM_HandleTypeDef *tim = RT_NULL;
TIM_OC_InitTypeDef oc_config = {0};
TIM_MasterConfigTypeDef master_config = {0};
TIM_ClockConfigTypeDef clock_config = {0};
RT_ASSERT(device != RT_NULL);
tim = (TIM_HandleTypeDef )&device->tim_handle;
/ configure the timer to pwm mode /
tim->Init.Prescaler = 167;
tim->Init.CounterMode = TIM_COUNTERMODE_UP;
tim->Init.Period = 100;
tim->Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
#if defined(SOC_SERIES_STM32F1) || defined(SOC_SERIES_STM32L4)
tim->Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
#endif
if (HAL_TIM_Base_Init(tim) != HAL_OK)
{
LOG_E("%s pwm init failed", device->name);
result = -RT_ERROR;
goto __exit;
}
if (HAL_TIM_PWM_Init(tim) != HAL_OK)
{
LOG_E("%s pwm init failed", device->name);
result = -RT_ERROR;
goto __exit;
}
clock_config.ClockSource = TIM_CLOCKSOURCE_INTERNAL;
if (HAL_TIM_ConfigClockSource(tim, &clock_config) != HAL_OK)
{
LOG_E("%s clock init failed", device->name);
result = -RT_ERROR;
goto __exit;
}
master_config.MasterOutputTrigger = TIM_TRGO_RESET;
master_config.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;
if (HAL_TIMEx_MasterConfigSynchronization(tim, &master_config) != HAL_OK)
{
LOG_E("%s master config failed", device->name);
result = -RT_ERROR;
goto __exit;
}
oc_config.OCMode = TIM_OCMODE_PWM1;
oc_config.Pulse = 50;
oc_config.OCPolarity = TIM_OCPOLARITY_HIGH;
oc_config.OCFastMode = TIM_OCFAST_DISABLE;
oc_config.OCNIdleState = TIM_OCNIDLESTATE_RESET;
oc_config.OCIdleState = TIM_OCIDLESTATE_RESET;
/ pwm pin configuration /
HAL_TIM_MspPostInit(tim);
/ config pwm channel /
if (device->channel & 0x01)
{
if (HAL_TIM_PWM_ConfigChannel(tim, &oc_config, TIM_CHANNEL_1) != HAL_OK)
{
LOG_E("%s channel1 config failed", device->name);
result = -RT_ERROR;
goto __exit;
}
}
if (device->channel & 0x02)
{
if (HAL_TIM_PWM_ConfigChannel(tim, &oc_config, TIM_CHANNEL_2) != HAL_OK)
{
LOG_E("%s channel2 config failed", device->name);
result = -RT_ERROR;
goto __exit;
}
}
if (device->channel & 0x04)
{
if (HAL_TIM_PWM_ConfigChannel(tim, &oc_config, TIM_CHANNEL_3) != HAL_OK)
{
LOG_E("%s channel3 config failed", device->name);
result = -RT_ERROR;
goto __exit;
}
}
if (device->channel & 0x08)
{
if (HAL_TIM_PWM_ConfigChannel(tim, &oc_config, TIM_CHANNEL_4) != HAL_OK)
{
LOG_E("%s channel4 config failed", device->name);
result = -RT_ERROR;
goto __exit;
}
}
/ enable update request source /
__HAL_TIM_URS_ENABLE(tim);
HAL_TIM_PWM_Start(tim, TIM_CHANNEL_1);
/ Update frequency value */
HAL_TIM_GenerateEvent(tim, TIM_EVENTSOURCE_UPDATE);
__exit:
return result;
}