【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用体验】安森美官方Semiconductor_IDE搭建（之三）

2020-7-18 21:43:37 1273

0 ` 首先键入官方网站下载ON_Semiconductor_IDE_Installer。文件473M，耐心下载。IDE是基于Eclipse开发的。 1. 从www.onsemi.com/RSL10下载ON Semiconductor IDE安装程序。 2.从www.onsemi.com/RSL10下载RSL10软件包，然后解压缩RSL10 CMSIS-Pack 按照下图操作，加载RSL10 CMSIS-Pack ONSemiconductor.RSL10.3.3.75 这是加载之后的，选在点灯的实例代码跟keil的完全一致 /* ---------------------------------------------------------------------------- * Copyright (c) 2017 Semiconductor Components Industries, LLC (d/b/a * ON Semiconductor), All Rights Reserved * * This code is the property of ON Semiconductor and may not be redistributed * in any form without prior written permission from ON Semiconductor. * The terms of use and warranty for this code are covered by contractual * agreements between ON Semiconductor and the licensee. * * This is Reusable Code. * * ---------------------------------------------------------------------------- * app.c * - Simple application using a DIO5 input to control a DIO6 output * ---------------------------------------------------------------------------- * $Revision: 1.11 $ * $Date: 2019/11/11 17:45:11 $ * ------------------------------------------------------------------------- / #include "app.h" #include / ---------------------------------------------------------------------------- * Function : void DIO0_IRQHandler(void) * ---------------------------------------------------------------------------- * Description : Toggle the toggle status global flag. * Inputs : None * Outputs : None * Assumptions : None * ------------------------------------------------------------------------- / void DIO0_IRQHandler(void) { static uint8_t ignore_next_dio_int = 0; if (ignore_next_dio_int == 1) { ignore_next_dio_int = 0; } else if (DIO_DATA->ALIAS[BUTTON_DIO] == 0) { / Button is pressed: Ignore next interrupt. * This is required to deal with the debounce circuit limitations. / ignore_next_dio_int = 1; / Invert toggle status / if (led_toggle_status == 1) { led_toggle_status = 0; PRINTF("LED BLINK DISABLED "); } else { led_toggle_status = 1; PRINTF("LED BLINK ENABLED "); } } } / ---------------------------------------------------------------------------- * Function : void Initialize(void) * ---------------------------------------------------------------------------- * Description : Initialize the system by disabling interrupts, configuring * the required DIOs and DIO interrupt, * updating SystemCoreClockUpdate and enabling interrupts. * Inputs : None * Outputs : None * Assumptions : None * ------------------------------------------------------------------------- / void Initialize(void) { / Mask all interrupts / __set_PRIMASK(PRIMASK_DISABLE_INTERRUPTS); / Disable all existing interrupts, clearing all pending source / Sys_NVIC_DisableAllInt(); Sys_NVIC_ClearAllPendingInt(); / Test DIO12 to pause the program to make it easy to re-flash / DIO->CFG[RECOVERY_DIO] = DIO_MODE_INPUT \| DIO_WEAK_PULL_UP \| DIO_LPF_DISABLE \| DIO_6X_DRIVE; while (DIO_DATA->ALIAS[RECOVERY_DIO] == 0); / Setup DIO5 as a GPIO input with interrupts on transitions, DIO6 as a * GPIO output. Use the integrated debounce circuit to ensure that only a * single interrupt event occurs for each push of the pushbutton. * The debounce circuit always has to be used in combination with the * transition mode to deal with the debounce circuit limitations. * A debounce filter time of 50 ms is used. / Sys_DIO_Config(LED_DIO, DIO_MODE_GPIO_OUT_0); Sys_DIO_Config(BUTTON_DIO, DIO_MODE_GPIO_IN_0 \| DIO_WEAK_PULL_UP \| DIO_LPF_DISABLE); Sys_DIO_IntConfig(0, DIO_EVENT_TRANSITION \| DIO_SRC(BUTTON_DIO) \| DIO_DEBOUNCE_ENABLE, DIO_DEBOUNCE_SLOWCLK_DIV1024, 49); NVIC_EnableIRQ(DIO0_IRQn); printf_init(); / Unmask all interrupts / __set_PRIMASK(PRIMASK_ENABLE_INTERRUPTS); } / ---------------------------------------------------------------------------- * Function : int main(void) * ---------------------------------------------------------------------------- * Description : Initialize the system, then toggle DIO6 as controlled by * DIO5 (press to toggle input/output). * Inputs : None * Outputs : None * Assumptions : None * ------------------------------------------------------------------------- / int main(void) { /Initialize global variables / led_toggle_status = 1; / Initialize the system / Initialize(); PRINTF("DEVICE INITIALIZED "); / Spin loop / while (1) { / Refresh the watchdog timer / Sys_Watchdog_Refresh(); / Toggle GPIO 6 (if toggling is enabled) then wait 0.5 seconds / if (led_toggle_status == 1) { Sys_GPIO_Toggle(LED_DIO); PRINTF("LED %s ", (DIO->CFG[LED_DIO] & 0x1 ? "ON" : "OFF")); } else { Sys_GPIO_Set_Low(LED_DIO); } Sys_Delay_ProgramROM((uint32_t)(3 SystemCoreClock)); } } 复制代码点击左上角锤子一样的编译 Build the Sample Code。编辑记过如下： 21:28:32 ** Incremental Build of configuration Debug for project blinky ** make -j4 all Invoking: Cross ARM GNU Print Size arm-none-eabi-size --format=berkeley "blinky.elf" text data bss dec hex filename 2164 100 1036 3300 ce4 blinky.elf Finished building: blinky.siz 21:28:33 Build Finished. 0 errors, 0 warnings. (took 1s.373ms) 复制代码下载：修改Sys_Delay_ProgramROM((uint32_t)(3 * SystemCoreClock)); 延长闪烁时间 ` 0
2020-7-18 21:43:37　　评论淘帖0 举报相关推荐 • 【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用体验】+ 点灯试验 826 • 【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用体验】开箱检测 1810 • 【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用体验】+开箱 1010 • 【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用体验】点灯走起 1738 • 【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用体验】（1）开箱 1198 • 【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用申请】基于RSL10的智能门锁 838 • 【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用申请】基于BLE5.0 RSL10开发板的智能楼宇应用 680 • 【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用体验】虽然小，但很强 --记安森美RSL10 2050 • 【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用申请】智能门锁项目在on Semiconductor BLE5.0开发板的实现 683 • 【大联大世平ON Semiconductor BLE5.0 RSL10开发板试用体验】（2）ONsemi的IDE和blinky工程 1313