fieldfox中的工具包不会显示在菜单中

FieldFox使用XML calkit格式的文件（扩展名为.xkt）。
如果文件已损坏，则不会加载。
使用什么版本的Calkit Editor来生成文件？
你能把你的文件附在帖子上，以便我可以查看吗？
尝试SCPI查询“SENS：CORR：COLL：CKIT：LAB：CAT？”
这将是已成功解析和加载的所有calkits的标签。
确保您的calkit具有定义的唯一标签，否则它可能会被另一个具有相同标签的套件所掩盖。
另一种可能性 - FieldFox的GUI仅显示带有连接器的calkits，这些连接器与GUI中选择的连接器相匹配。
因此，当您在GUI中选择“连接器”时，可以选择连接器类型，然后显示可能使用的一组calkits（套件中的匹配连接器）。
（此呈现的列表由您刚刚选择的连接器过滤。）Wil



     以下为原文

  FieldFox uses files in the XML calkit format (extension .xkt).  If the file is corrupt, it will not be loaded.  What version of the Calkit Editor was used to produce the file?  Can you attach your file to a post so I can examine it?

Try the SCPI query "SENS:CORR:COLL:CKIT:LAB:CAT?"

This will the labels of all of the calkits that have been successfully parsed and loaded.

Make sure your calkit has a unique label defined, otherwise it might be masked by another kit with the same label.

Another possibility - FieldFox's GUI only displays calkits with connectors defined which match the connector chosen in the GUI.  So when you 'choose connectors' in the GUI, you choose a connector type, and then the set of calkits that might be used (matching connectors in the kit) is presented.  (This presented list is filtered by the connector that you just chose.)

Wil

非常感谢您提供的信息。
这是文件。
Fieldfox没有可能出现问题的SMA连接器选择。
就像我说的文件是在fieldfox中它在数据链接上显示¨显示文件E由：theamberco于2014年3月25日上午10:29
85033-SMA.txt6.1 KB



     以下为原文

  Thanks a lot for the information. Here is the file. The Fieldfox does not have an SMA connector choice that may be the issue. Like I said the file is in the fieldfox it shows it on data link ¨show Files¨

Edited by: theamberco on Mar 25, 2014 10:29 AM

附件

• 85033-SMA.xkt6.1 KB
  
• 85033-SMA.txt6.1 KB
  

迈克，根据过去与你的电子邮件交流，我怀疑你没有正确上传文件。
我建议你去http://www.home.agilent.com/agilent/editorial.jspx?ckey=2152552&id=2152552&nid=-11143.0.00&lc=eng&cc=US并尝试安装一个
您的VNA中尚未包含的校准工具包文件。
有一些不起眼的校准套件，包括75欧姆，Maury微波TNC和波导。
尝试上传FieldFox固件中尚未包含的一个或两个。
任何小于WR137的波导都无法工作，小波导的工作频率将无法工作在6 GHz。
但我非常确定FieldFox的固件中没有WR137波导校准套件，但您可以从安捷伦网站下载并将其上传到FieldFox。
如果您能够从安捷伦网站上传几个校准套件文件，但不能上传您要上传的SMA文件，那么我会怀疑SMA文件有问题。
但是，如果我怀疑你做错了，那么它不适用于任何校准套件文件。
将校准套件文件上传到Agilent FieldFox并不是火箭科学。
FieldFox的菜单中没有SMA套件，但这并不会停止定义SMA的校准套件文件。
如果你特别疯狂，你可以用PL259甚至香蕉插头定义一个校准套件！
我的钱是在使用SMA文件时出错。
戴夫



     以下为原文

  Mike,
Judging by past email exchanges with you,  I suspect that you are not uploading the file correctly.  

I suggest you go to 

http://www.home.agilent.com/agilent/editorial.jspx?ckey=2152552&id=2152552&nid=-11143.0.00&lc=eng&cc=US

and attempt to install one of the cal kit files that is not already in your VNA. There are some obscure calibration kits there Including 75 Ohm, Maury Microwave TNC and waveguide.  Try uploading one or two that is not already in the FieldFox firmware.  Any waveguide smaller than WR137 would not work ad to the operating frequency of smaller waveguides will not work at 6 GHz. But I am pretty sure that the FieldFox will not have a WR137 waveguide calibration kit in its firmware,  but you can download one from the Agilent web site and upload that to your FieldFox. 

If you are able to upload a couple of calibration kit files from the Agilent web site, but not the SMA files you want to upload, then I would suspect a problem with the SMA file. But if as I suspect that you are doing it wrong,  then it will not for any cal kit file. 

It is not rocket science uploading a calibration kit file to an Agilent FieldFox.  

The FieldFox does not have an SMA kit in its menu,  but that doesn't stop your calibration kit file defining an SMA. If you were particulary crazy you could define a cal kit with PL259 or even banana plugs!

My money is on making a mistake using the SMA file.

Dave

它只适用于XML文件而不适用于XKT。



     以下为原文

  It only Works with the XML file not the XKT.

> {quote：title = theamberco写道：} {quote}>它只适用于XML文件而不是XKT。
所以你在http://www.home.agilent.com/agilent/editorial.jspx?ckey=2152552&id=2152552&nid=-11143.0.00&lc=eng&cc=上没有说明任何.xkt文件
美国可以加载到FieldFox吗？
据我所知，.xml *和* .xkt文件都是*两个*基本上是标记文件，其中.xkt中包含更多信息。
我必须承认，其中一些看起来有点奇怪。
例如，我看到的第一个.xkt文件，这是一个波导http://www.home.agilent.com/upload/cmc_upload/All/WR137_WG14.xkt有行**但没有什么可以启动*
“CalKitVersion” *。
我本来期望这些标签成对出现，例如* N9911X WR137 *或* WR-137（C波段）波导SOLT / TRL校准套件*而不是单个标签，如：**也许安捷伦的某些人可以对此发表评论。
但是，有些似乎有点“奇怪”，带有结束标签但没有开始标签，文件本质上看起来相当简单的文件格式，不像我自己的8720D，这是一些未公开的二进制格式。
在FieldFox的校准套件页面上，似乎有几乎随机的.xml和.xkt文件组合。
所有的波导套件都是.xkt文件，但是两个APC / 7 mm套件，85050C和85050D也是如此。
也许xml或.xkt扩展的选择取决于风吹的方式，因为对我来说没有明显的逻辑。
DaveEdited：drkirkby于2014年4月10日上午11:41



     以下为原文

  > {quote:title=theamberco wrote:}{quote}
> It only Works with the XML file not the XKT.


So are you saying none of the .xkt files at 

http://www.home.agilent.com/agilent/editorial.jspx?ckey=2152552&id=2152552&nid=-11143.0.00&lc=eng&cc=US

can be loaded into the FieldFox? 

As far as I can see, the .xml *and* .xkt files are *both* basically markup files, with the .xkt having a bit more information in them. I must admit, some of them seem a bit strange. For example, the first .xkt file I see, which is a waveguide one

http://www.home.agilent.com/upload/cmc_upload/All/WR137_WG14.xkt

has the line

**

but there is nothing to start the *"CalKitVersion"*. I would have expected the tags to come in pairs, like

*N9911X WR137*
or
*WR-137 (C band) Waveguide SOLT/TRL Calibration Kit*

rather than single tags like:

**

Perhaps someone from Agilent can comment on this. 

But not withstanding some seem to be a little "odd", with end tags but no start tags, the files essentially look a fairly easy file format, unlike those for my own 8720D, which is some binary format that is not made public. 

At the page for the cal kits for the FieldFox, there seems to be an almost random mix of .xml and .xkt files. All the waveguide kits are .xkt files, but so are two of the APC/7 mm kits, the 85050C and 85050D. 

Maybe the choice of xml or .xkt extension depends on what way the wind is blowing, since there is no obvious logic to me. 

Dave

Edited by: drkirkby on Apr 10, 2014 11:41 AM

> {quote：title = drkirkby写道：} {quote}>你是说什么。> http://www.home.agilent.com/agilent/editorial.jspx?ckey=2152552&id上没有.xkt文件
= 2152552＆amp; nid = -11143.0.00＆amp; lc = eng＆amp; cc = US >>可以加载到FieldFox中？
我尝试将它转移到fieldfox的WR137，但它没有出现在菜单中，我的fieldfox在show files下有其他.XKT文件，它们也没有显示在cal菜单中。
编辑：theamberco于2014年4月11日上午11:54编辑：theamberco于2014年4月11日上午11:54



     以下为原文

  > {quote:title=drkirkby wrote:}{quote}

> So are you saying none of the .xkt files at 
> 
> http://www.home.agilent.com/agilent/editorial.jspx?ckey=2152552&id=2152552&nid=-11143.0.00&lc=eng&cc=US
> 
> can be loaded into the FieldFox? 

I tried the WR137 it transfers to the fieldfox but it does not appears in the menus, my fieldfox has other .XKT files under show files and they dont show up in the cal menus either.

Edited by: theamberco on Apr 11, 2014 11:54 AM
Edited by: theamberco on Apr 11, 2014 11:54 AM

戴夫，正如你所说，“。xkt”文件也是像“.xml”文件一样的XML文件。
另外正如您所注意到的，这两种格式非常相似，但“.xkt”文件的内容更多。
首先引入'.xml'文件格式，并且特定于FieldFox。
'.xkt'格式的变化使其更具可扩展性，例如能够支持更复杂的校准套件类型，如基于安捷伦数据的校准套件。
事实上，从PNA固件A.10.00.00开始的PNA分析仪（运行Windows 7的PNA）现在也支持相同的校准套件文件的xkt格式。
@'theamberco'：我在PNA方面的专长比FieldFox更多，所以我需要让其他人知道你为什么无法让你的FieldFox将你的xkt文件加载到其列表中的原因
套件。



     以下为原文

  Dave, as you noted, '.xkt' files are also XML files like the '.xml' files are.  Also as you noticed, the two formats are very similar but the '.xkt' files have more content.  The '.xml' file format was introduced first, and is specific to FieldFox.  The '.xkt' format has changes that made it more extensible, for example to be able to support more complex cal kit types like the Agilent data-based cal kits.  In fact, PNA analyzers beginning with PNA Firmware A.10.00.00 (PNAs running Windows 7) now also support the same xkt format for cal kit files.

@ 'theamberco': my expertise is more in PNA than FieldFox so I will need to let someone else chime-in on what might be the cause of why you haven't been able to get your FieldFox to load your xkt files into its list of kits.

我应该提供更多背景信息，因为我是.xkt文件的来源Mike（theamberco）想要上传到他的N9912A。
我创建了一个SMA校准套件，其中包含FieldFox应该能够使用的文件。
我现在*没有* FieldFox自己检查文件，但我确实*今天购买了N9912A *，所以应该在星期三或星期四。
我可以自己检查一下。
无论如何，这是背景。
1）去年11月我创建了Mike试图使用的早期版本的文件。
我使用了独立的CalKitEditor Rev：1。0。18。18。0（2013年9月），这是当时的最新版本，现在仍然是最新版本。
可以在此处找到校准套件编辑器。
http://na.tm.agilent.com/pna/apps/#calkiteditor 2）虽然我没有FieldFox，但我尝试使用FieldFox的DataLink 4.64软件打开文件。
FieldFox的Datalink软件一直报告“CalKitEditor.exe已停止工作”。
正如我在2013年11月报道的那样.https：//community.keysight.com/message/64200
3）Wil（安捷伦员工在论坛上使用名称'Wils'）在安捷伦论坛上写道，4.64版本的Datalink的calkit编辑器存在缺陷.Datalink 4.64试图强制执行独立的calkit编辑器版本1.0.5018.0所做的事情
不是，所以可以在calkit编辑器1.0.5018.0中创建一个calkit文件，DataLink 4.64无法使用.Wil友好地编辑了文件，使其与DataLink 4.64兼容。他的版本在这里。附件如下：4）
我向其他人发布了上述文件的链接，我知道他在FieldFox中成功使用了*修改版本*。我相信他使用的文件就是这里的文件.http：//www.vnacalibration.co。
uk / support / 85033 / HP / downloads / FieldFox / 85033-SMA.xkt据我所知，从文件Wil发布的更改附在下面：到http://www.vnacalibration.co.uk的文件
/support/85033/HP/downloads/FieldFox/85033-SMA.xkt非常小，而且只是化妆品。例如* Custom已更改为SM
A，表示它是SMA。
*被改为2.这对我来说似乎更合乎逻辑，因为人们会期望任何类型的XML文件都有“开始”和“结束”标签，因为需要更好的表达。
所以我相信迈克应该可以将文件上传到他的FieldFox，网址为http://www.vnacalibration.co.uk/support/85033/HP/downloads/FieldFox/85033-SMA.xkt，并获得定义的SMA校准套件
。
尽管我对N9912A的性能表示担忧，但我刚买了一台，所以我会在几天内自行检查一下。
（不幸的是，虽然N9912A有很多便宜的使用，但N9914A也是如此，这似乎是一个* *更好的仪器）。
一旦我拿到N9912A，我会在几天内报告，但是如果有人能查看文件http://www.vnacalibration.co.uk/support/85033/HP/downloads/FieldFox/85033-SMA。
xkt cal kit文件可以上传到FieldFox中，并且表现为人们期望cal kit文件的行为，我会感兴趣。
戴夫
85033.xkt.zip1.0 KB



     以下为原文

  I should give more background information to this, since I am the source of the .xkt file Mike (theamberco) wants to upload to his N9912A. I created an SMA cal kit, with a file the FieldFox should be able to use. 

I don't *currently* have a FieldFox to check the file myself, but I did in fact *purchase an N9912A today*, so should have it Wednesday or Thursday. I will be able to check this myself. Anyway, this is the background. 

1) Last November I created an earlier version of the file Mike is trying to use. I used the standalone CalKitEditor Rev: 1.0.5018.0 (Sept 2013) which was the latest version at the time, and still is current. The cal kit editor can be found here. 

http://na.tm.agilent.com/pna/apps/#calkiteditor

2) Although I did not have a FieldFox, I attempted to open the file using the FieldFox's DataLink 4.64 software. The FieldFox's Datalink software kept  reporting that "CalKitEditor.exe has stopped working".

as I reported back in November 2013. 
https://community.keysight.com/message/64200
 

3) Wil (Agilent employee with usename 'Wils" on the forum) wrote on the Agilent forum that there was a defect in the 4.64 version of Datalink's calkit editor. Datalink 4.64 was trying to enforce something the standalone calkit editor version 1.0.5018.0 did not, so it was possible to create a cal kit file in the calkit editor 1.0.5018.0 which DataLink 4.64 could not use. Wil kindly edited the file to make it compatible with the DataLink 4.64. His version is here. 
Attached below:

4) I posted a link to the above file to someone else, who I know used a *modified version* of it successfully in his FieldFox. I believe the file that he used is the one here. 

http://www.vnacalibration.co.uk/support/85033/HP/downloads/FieldFox/85033-SMA.xkt

As far as I am aware, the changes made from the file Wil posted
Attached below:

to the file at 

http://www.vnacalibration.co.uk/support/85033/HP/downloads/FieldFox/85033-SMA.xkt

are fairly minor, and exclusively cosmetic. For example 

* Custom was changed to SMA, to indicate it is SMA. 
*  was changed to 2. This seems more logical to me, as one would expect any sort of XML file to have "start" and "end" tags, for want of a better expression. 

So I believe Mike should be able to upload the file at 

http://www.vnacalibration.co.uk/support/85033/HP/downloads/FieldFox/85033-SMA.xkt

to his FieldFox, and get an SMA cal kit defined. 

Despite my concerns about the performance of the N9912A, I have just bought one, so will check this myself in a couple of days. (Unfortunately, although there are lots of cheap used N9912As around, the same is not true of the N9914A, which seems a *much* better instrument). 

I will report back in a couple of days once I get my N9912A, but if anyone else can check if the file 

http://www.vnacalibration.co.uk/support/85033/HP/downloads/FieldFox/85033-SMA.xkt

cal kit file can be uploaded into a FieldFox, and behave as one would expect a cal kit file to behave, I would be interested. 

Dave


附件

• 85033 (3).xkt.zip1.0 KB
  
• 85033.xkt.zip1.0 KB
  

大家好，想问一下是否找到了上述问题的解决方案。
目前我面临与theamberco相同的情况：自定义CalKit被发送到FieldFox并使用“show files”列在DataLink中，但是新的连接器系列和套件本身都没有显示在FieldFox的Calibration菜单中
。
与.xkt-Format中的其他CalKits相同，如上面列出的85033-SMA.xkt Dave。
使用“SENS：CORR：COLL：CKIT：LAB：CAT？” - 查询Wil提到我的CalKit甚至其他人都出现在仪器控制台中，因此应该正确加载它们。
使用FieldFox中的DataLink软件打开文件也可以。
固件是最新的：A.07.54所以.xkt-Files应该可以工作。
感谢任何帮助，我的想法已经不多了。
谢谢！



     以下为原文

  Hi guys,

wanted to ask if there's been found a solution to the problem above.

At the moment i'm facing the same situation as theamberco: a custom CalKit was sent to the FieldFox and is listed in DataLink using "show files" but neither the new connector family nor the Kit itself show up in the Calibration menu on the FieldFox. Same problem with other CalKits in .xkt-Format as the 85033-SMA.xkt Dave listed above.

Using the "SENS:CORR:COLL:CKIT:LAB:CAT?"-query Wil mentioned my CalKit and even the others show up in the instrument console so they should be loaded right. Opening the Files using the DataLink-software from the FieldFox works too. Firmware is up to date: A.07.54 so .xkt-Files should work.

Appreciate any help, I'm running out of ideas. Thanks!

> {quote：title = merluis写道：} {quote}>大家好，>>想问一下是否找到了上述问题的解决方案。
>>目前我面临与theamberco相同的情况：自定义CalKit被发送到FieldFox并在DataLink中使用“show files”列出，但新的连接器系列和套件本身都没有显示在校准菜单上
FieldFox。
与.xkt-Format中的其他CalKits相同，如上面列出的85033-SMA.xkt Dave。
>>使用“SENS：CORR：COLL：CKIT：LAB：CAT？” - 查询Wil提到我的CalKit甚至其他人都出现在仪器控制台中，因此应该正确加载它们。
使用FieldFox中的DataLink软件打开文件也可以。
固件是最新的：A.07.54所以.xkt-Files应该可以工作。
>>感谢任何帮助，我的想法已经不多了。
谢谢！
根据您的信任，这是一个“错误”或“功能”，我认为这是一个错误。
解决方法是使用相同的连接器系列创建第二个套件，但是将套件称为其他套件。
这样，我创建的SMA工具包+ theamberco +试图加载，确实正确加载。
校准套件需要采用XML格式的N9912A，但我相信所有其他分析仪都需要.xml或.xkt。
无论如何，这是我的理解。
我知道更长的是N9912A。
也见这个帖子。
为什么N9912A中没有APC7（7mm）或F（75欧姆）校准套件？
在那，我看不到85031B 7毫米6 GHz经济校准套件，但是一旦添加了另一个APC7套件，85050C，85050C和85031B都可以看到。
总而言之，*确保您有两个具有相同连接器系列*的套件。
如果需要，可以将其称为“虚拟”，或类似的东西。
这只出现在稀有连接器系列（F，SMA，APC7和I期望为7-16）上，因为对于其他系列的连接器，如N和3.5 mm，固件中将有几个套件。
Dave编辑：drkirkby于2014年9月19日下午3:20编辑：drkirkby于2014年9月19日下午3:21



     以下为原文

  > {quote:title=merluis wrote:}{quote}
> Hi guys,
> 
> wanted to ask if there's been found a solution to the problem above.
> 
> At the moment i'm facing the same situation as theamberco: a custom CalKit was sent to the FieldFox and is listed in DataLink using "show files" but neither the new connector family nor the Kit itself show up in the Calibration menu on the FieldFox. Same problem with other CalKits in .xkt-Format as the 85033-SMA.xkt Dave listed above.
> 
> Using the "SENS:CORR:COLL:CKIT:LAB:CAT?"-query Wil mentioned my CalKit and even the others show up in the instrument console so they should be loaded right. Opening the Files using the DataLink-software from the FieldFox works too. Firmware is up to date: A.07.54 so .xkt-Files should work.
> 
> Appreciate any help, I'm running out of ideas. Thanks!
Depending on who you believe, this is a "bug" or a "feature" I consider it a bug myself. 
A workaround is to create a second kit, with the same connector family, but call the kit something else. That way, the SMA kit I created, that +theamberco+ tried to load, does load properly. 
The cal kits need to be in XML format for the N9912A, but I believe all the other analyzers will take .xml or .xkt. 
That's my understanding anyway. I know longer have an N9912A. 
See this thread too. 
Why is there no APC7 (7mm) or F (75 Ohm) calibration kits in N9912A?

In that, I could not see the 85031B 7 mm 6 GHz economy calibration kit, but once another APC7 kit was added, the 85050C, both the 85050C and the 85031B could be seen. 

So in summary, *make sure you have two kits with the same connector family*. If need be, one can be called "dummy", or something like that. This only shows up on rarer connector families (F, SMA, APC7 and I expect 7-16 too), since for other families of connectors, like N and 3.5 mm, there will be several kits in the firmware. 

Dave

Edited by: drkirkby on Sep 19, 2014 3:20 PM

Edited by: drkirkby on Sep 19, 2014 3:21 PM

目前，N9912A的校准GUI不会读取较新的.xkt文件，只读取.xml文件。
N9923A和所有其他FieldFox目前支持2端口校准GUI，可以读取.xkt文件。
未来版本（下一个版本，现在在QA中）将允许N9912A读取.xkt文件，并且所有传送的calkit文件将转换为.xkt - 旧的.xml格式将被弃用。
由于当前版本的calkit编辑器不生成.xml文件，因此这将允许calkit编辑器生成N9912A可读的文件！
我相信这解释了为什么@ theamberco的N9912A无法读取他的文件。
顺便提一下，.xkt格式增加了对波形的支持，.xml不支持。
因此，在下一个版本中，N9912A将能够查看和使用波导套件。
同样在下一个版本中，即使只有一个与您选择的连接器匹配，N9912A的校准GUI也会显示您选择的套件。
至于格式错误的XML的注释，“”是“”的XML简写，即没有内容的XML元素。
特别是不是'结束标记'，而是整个空元素。
是一个需要配对的“结束标记”。
因此，文件中的XML格式正确，但此文件未指定该XML节点/元素的值。
作为为N9912A创建工具包的短期解决方法，您必须从现有.xml文件的副本开始并手动修改（使用XML或纯文本编辑器）以包含您需要的标准和标准数据
。
遗憾的是，即使XML格式正确，也必须遵循一些规则，否则FieldFox可能无法读取您的工具包。
通常，这些规则是确保存在所有必需元素，正确指定标准ID且不冲突，并且连接器名称完全匹配（标准定义和连接器定义之间）。
当然，上述方法不适用于波导套件，因为.xml格式没有指定波导特定信息所需的元素。
希望这可以帮助。
会



     以下为原文

  Currently, N9912A's calibration GUI does not read the newer .xkt files, only .xml files.  N9923A and all other FieldFoxes currently support a 2-port capable calibration GUI which does read .xkt files.  A future release (the next one, in QA now) will allow N9912A to read .xkt files, and all of the shipping calkit files will be converted to .xkt - the old .xml format will be deprecated.  Since the current version of the calkit editor does not generate .xml files, this will allow the calkit editor to generate files readable by N9912A!

I believe this explains why @theamberco's N9912A cannot read his files.

Incidentally, the .xkt format adds support for waveguide, which .xml did NOT support.  So in the next release, N9912A will be able to see and use waveguide kits.

Also in the next release, N9912A's calibration GUI will show you your chosen kit even if there is only one that matches your selected connector.

As for the comments on malformed XML, "" is XML shorthand for "", i.e. an XML element with no content.  In particular  is not an 'end tag', but an entire empty element.   is an "end tag" that would need to be paired with .  So the XML in the file is well formed, but this file does not specify a value for that XML node/element.

As a short term workaround for creating kits for N9912A, you'll have to start with a copy of an existing .xml file and modify it by hand (with an XML or plain text editor) to contain the standards and standards data that you require.  Unfortunately, there are a few rules you have to follow or your kit may not be readable by the FieldFox even if the XML is well formed.  Generally, these rules are around making sure that all the required elements are present, standard id's are properly specified and non-conflicting, and connector names match exactly (between standard definitions, and connector definitions).

Of course, the above method will not work for waveguide kits as the .xml format does not have the required elements to specify waveguide specific information.

Hope this helps.

Wil

我不是说xkt格式不是更好，但我确信XML可以被修改以支持波导。
波导套件的参数比同轴套件的参数简单。
所需的额外信息是波导的截止频率。
不需要C0，C1，C2，C3，L0，L1，L2，L3s。
只是长度和截止频率。
无论如何，听到这个很好。
虽然我不再拥有N9912A，但我知道有人这样做。
FieldFoxes似乎没有太多运气*购买了N9923A CertiPrime装置，它在大约一个月内就出现了硬件故障。
*买了二手N9912A，它是DOA。
希望我买的下一个可以。
我喜欢这些乐器 - 看起来他们似乎不喜欢我！
戴夫



     以下为原文

  I'm not saying the xkt format is not better, but I am sure the XML could have been modified to support waveguide. The parameters of a waveguide kit are simpler than those of a coaxial kit. The extra bit of information that is needed is the cutoff frequency of the waveguide. There are no C0, C1, C2, C3, L0, L1, L2, L3s needed. Just lengths and a cutoff frequency. 

Anyway, it is good to hear this. Although I no longer have an N9912A, I know someone who does. 

I don't seem to have much luck with FieldFoxes

* Bought an N9923A CertiPrime unit and it developed a hardware fault in about a month. 
* Bought a used N9912A and it was DOA.

Hopefully, the next one I buy will be ok. I like the instruments - it just seems they don't like me!!

Dave

@Wil和Dave非常感谢您的回复！
尝试将.xkt文件修改为.xml，但没有运气，因为我的CalKit是基于数据的，根据bhokkan只支持.xkt-Files。
但是听说包括.xkt支持在内的新固件更新非常棒！
由于更新是在QA中，是否有估计的发布日期？
再次感谢，给我带来了很多麻烦。
卢卡斯



     以下为原文

  @Wil and Dave
Thanks a lot for your replies!

Tried modifying the .xkt-Files to .xml, but no luck with that, given the fact that my CalKit is data-based, wich according to bhokkan is only supported in .xkt-Files.
But hearing about the new firmware-update including the .xkt-support is great! With the update being in QA, is there an estimated release date?

Thanks again, spared me lots of trouble.
Lukas

>尝试将.xkt文件修改为.xml，但没有运气，因为我的CalKit是基于数据的，据bhokkan只支持.xkt-Files。
>但是听说包括.xkt支持在内的新固件更新非常棒！
由于更新是在QA中，是否有估计的发布日期？
>>再次感谢，给我带来了很多麻烦。
> Lukas只需仔细检查以确保我们对要求有所了解......您有N9912A并且正在使用基于数据的校准套件用于1端口OSL校准？
此致，Afsi



     以下为原文

  > Tried modifying the .xkt-Files to .xml, but no luck with that, given the fact that my CalKit is data-based, wich according to bhokkan is only supported in .xkt-Files.
> But hearing about the new firmware-update including the .xkt-support is great! With the update being in QA, is there an estimated release date?
> 
> Thanks again, spared me lots of trouble.
> Lukas

Just double-checking to make sure we are clear on the requirements .. you have an N9912A and are using a data-based cal kit for the 1-port OSL cal?

Regards,
Afsi

嗨，Afsi，确切地说。编辑：merluis于2014年9月24日上午6:32



     以下为原文

  Hi Afsi,

exactly.

Edited by: merluis on Sep 24, 2014 6:32 AM

谢谢你的确认。
我们还没有关于xkt N9912A可用性的日期，但我们会尽快发布说明。
此致，Afsi Moaveni



     以下为原文

  Thanks for the confirmation.  We don't have a date yet for the xkt N9912A availability, but we'll be sure to post a note here as soon as it is available.

Regards,
Afsi Moaveni

@merluis，尚未发布发布日期，但应尽快发布。
会



     以下为原文

  @merluis,
  There is no release date published yet, but it should be available soon.

Wil

@Afsi和Wil感谢您提供有关更新的信息，感谢您在准备好发布时的任何通知。
并感谢您的努力！
关心卢卡斯



     以下为原文

  @Afsi and Wil

Thank you for the information, looking forward to the update, would appreciate any notification when it's ready to be released. And thanks for the efforts!

Regards
Lukas

Dave，关于.xml与.xkt文件的主题 - .xkt是安捷伦（现为是德科技）网络分析仪的标准，包括（前面提到的）数据库标准支持以及波导支持等功能
。
无论好坏，它不是.xml格式的扩展，而是完全重写，包括对PNA和ENA系列分析器的支持。
任何相似之处都是偶然的，不幸的是，FieldFox在安装完.xkt工作之前已经安装了.xml _just，最终需要转换到新的.xkt格式。
会



     以下为原文

  Dave,
  On the topic of the .xml vs. .xkt files - .xkt was developed to be a standard across Agilent (now Keysight) network analyzers, and includes features such as the (previously mentioned) databased standard support as well as waveguide support.  For better or worse, it is not an extension of the .xml format, but a complete rewrite including support for PNA and ENA series analyzers.  Any similarity is coincidental, and it is unfortunate that FieldFox shipped with .xml _just prior_ to Agilent completing the .xkt work, which ultimately required a transition to the new .xkt format.

Wil