获得IP核评估许可，无法在Vivado中看到IP

嗨@aytli，
xc7z020clg400-1是Zynq-7000，PL中带有Artix-7织物（根据Zynq-7000产品表）。
根据PG036，支持Zynq-7000和Artix-7：
但是，有一个与支持的设备系列相关的注释（请参阅little（1））：
如果您查看表格下方的注释，您将看到要获得支持设备的完整列表，您需要查看vivado IP目录。
这意味着，如果您在vivado中选择了设备而无法找到IP，则此IP不支持您所定位的部分：
所以Zybo Z7-20（以及更全面的xc7z020clg400-1）不支持HDMI IP。
实际原因是因为HDMI IP使用千兆位收发器和这部分（xc7z020clg400-1  - 与任何其他当前的Z-7020一样），没有任何收发器。
在vivado中选择部件时，您可以在产品表中看到这一点：
话虽如此，您仍然可以在Zybo Z7-20上安装HDMI输入，因为这块板作为ADV7611可以让你做HDMI RX 1.4a（我认为高达1080p）而且你不需要HDMI IP来使用它
。
它就像你添加DVI输入一样（因此你可以将数据，hsync和vsync信号作为输入，你只需要将视频输入到AXI4S和视频定时控制器作为免费的IP）。
希望有助于澄清，
FlorentProduct应用工程师 -  Xilinx技术支持EMEA ------------------------------------------
--------------------------------------------------
----------------------------不要忘记回答，kudo，并接受解决方案。
在原帖中查看解决方案



以下为原文

Hi @aytli,
 
xc7z020clg400-1 is a Zynq-7000 with an Artix-7 fabric in the PL (as per Zynq-7000 product table). According to the PG036, both Zynq-7000 and Artix-7 are supported:

 
However there is a note associated with the Supported Device Family (see the little (1) ):

 
And if you check the note below the table you will see that to get the complete list of supported device, you need to see the vivado IP catalog. This means that if you select your device in vivado and you cannot find the IP, then the part you are targeting is not supported for this IP:

 
So the Zybo Z7-20 (and more globally the xc7z020clg400-1 ) has no support for the HDMI IP.
 
The actual reason for this is because the HDMI IP is using Gigabit Transceivers and this part (xc7z020clg400-1 - as any other current Z-7020), does not have any transceivers. You can see this in the product table when selecting the part in vivado:

 
With that said, you can still have a HDMI input on your Zybo Z7-20 because this board as an ADV7611 which allows you to do HDMI RX 1.4a (up to 1080p I think) and you do not need the HDMI IP to use it. It acts like if you add DVI inputs (so you would have data, hsync and vsync signal as inputs and you would only need the video in to AXI4S and the Video Timing controller as IPs which are free).
 
Hope that helps to clarify,
Florent
Product Application Engineer - Xilinx Technical Support EMEA
------------------------------------------------------------------------------------------------------------------------
Don't forget to reply, kudo, and accept as solution.
View solution in original post

您需要在vivado项目中使用受支持的设备才能在IP目录中查看HDMI ip
https://www.xilinx.com/support/documentation/ip_documentation/v_hdmi_rx_ss/v2_0/pg236-v-hdmi-rx-ss.pdf
谢谢和RegardsBalkrishan -----------------------------------------------
---------------------------------------------请将帖子标记为
一个答案“接受为解决方案”，以防它有助于解决您的查询。如果一个帖子引导到解决方案，请给予赞誉。



以下为原文

you need to use supported device in your vivado project to see HDMI ip in IP catalog 
 
https://www.xilinx.com/support/documentation/ip_documentation/v_hdmi_rx_ss/v2_0/pg236-v-hdmi-rx-ss.pdf
Thanks and Regards
Balkrishan
--------------------------------------------------------------------------------------------
Please mark the post as an answer "Accept as solution" in case it helped resolve your query.
Give kudos in case a post in case it guided to the solution.

谢谢回复，
所以我按照核心用户指南中的说明，使用完全相同的板“Kintex-7 KC705”，然后我就可以将核心添加到程序框图中。
HDMI内核的产品页面表示它与Zynq-7000设备兼容。
Zybo Z7-20上的确切芯片是xc7z020clg400-1，不应该和Zynq-7000在同一系列中，因此与HDMI内核兼容吗？



以下为原文

Thanks for the reply,
 
So I followed the instructions in the user's guide for the core, using the exact same board "Kintex-7 KC705", and I was able to add the core to a block diagram. The product page for the HDMI core says it's compatible with Zynq-7000 devices. The exact chip on the Zybo Z7-20 is a xc7z020clg400-1, shouldn't that be in the same family as Zynq-7000, and thus compatible with the HDMI core?

我建议您在IP目录中引用精确支持的设备.xc7z020clg400-1不支持HDMI IP设备。
这可能需要在文档中进行更新
谢谢和RegardsBalkrishan -----------------------------------------------
---------------------------------------------请将帖子标记为
一个答案“接受为解决方案”，以防它有助于解决您的查询。如果一个帖子引导到解决方案，请给予赞誉。



以下为原文

I would recommend you to refer exact supported device in IP catalog .

xc7z020clg400-1 not supported device  for HDMI IP . This may be require update in documentationThanks and Regards
Balkrishan
--------------------------------------------------------------------------------------------
Please mark the post as an answer "Accept as solution" in case it helped resolve your query.
Give kudos in case a post in case it guided to the solution.

嗨@aytli，
xc7z020clg400-1是Zynq-7000，PL中带有Artix-7织物（根据Zynq-7000产品表）。
根据PG036，支持Zynq-7000和Artix-7：
但是，有一个与支持的设备系列相关的注释（请参阅little（1））：
如果您查看表格下方的注释，您将看到要获得支持设备的完整列表，您需要查看vivado IP目录。
这意味着，如果您在vivado中选择了设备而无法找到IP，则此IP不支持您所定位的部分：
所以Zybo Z7-20（以及更全面的xc7z020clg400-1）不支持HDMI IP。
实际原因是因为HDMI IP使用千兆位收发器和这部分（xc7z020clg400-1  - 与任何其他当前的Z-7020一样），没有任何收发器。
在vivado中选择部件时，您可以在产品表中看到这一点：
话虽如此，您仍然可以在Zybo Z7-20上安装HDMI输入，因为这块板作为ADV7611可以让你做HDMI RX 1.4a（我认为高达1080p）而且你不需要HDMI IP来使用它
。
它就像你添加DVI输入一样（因此你可以将数据，hsync和vsync信号作为输入，你只需要将视频输入到AXI4S和视频定时控制器作为免费的IP）。
希望有助于澄清，
FlorentProduct应用工程师 -  Xilinx技术支持EMEA ------------------------------------------
--------------------------------------------------
----------------------------不要忘记回复，kudo，并接受作为解决方案。



以下为原文

Hi @aytli,
 
xc7z020clg400-1 is a Zynq-7000 with an Artix-7 fabric in the PL (as per Zynq-7000 product table). According to the PG036, both Zynq-7000 and Artix-7 are supported:

 
However there is a note associated with the Supported Device Family (see the little (1) ):

 
And if you check the note below the table you will see that to get the complete list of supported device, you need to see the vivado IP catalog. This means that if you select your device in vivado and you cannot find the IP, then the part you are targeting is not supported for this IP:

 
So the Zybo Z7-20 (and more globally the xc7z020clg400-1 ) has no support for the HDMI IP.
 
The actual reason for this is because the HDMI IP is using Gigabit Transceivers and this part (xc7z020clg400-1 - as any other current Z-7020), does not have any transceivers. You can see this in the product table when selecting the part in vivado:

 
With that said, you can still have a HDMI input on your Zybo Z7-20 because this board as an ADV7611 which allows you to do HDMI RX 1.4a (up to 1080p I think) and you do not need the HDMI IP to use it. It acts like if you add DVI inputs (so you would have data, hsync and vsync signal as inputs and you would only need the video in to AXI4S and the Video Timing controller as IPs which are free).
 
Hope that helps to clarify,
Florent
Product Application Engineer - Xilinx Technical Support EMEA
------------------------------------------------------------------------------------------------------------------------
Don't forget to reply, kudo, and accept as solution.

谢谢你的回复，
我目前通过修改Digilent的HDMI示例项目，使用自己的DVI接收器/发送器内核，在此板上运行HDMI。
然而，它们的内核似乎阻止了HDMI流中的音频数据，而Xilinx HDMI内核可以提取音频数据并将其输出为I2S。
由于它不适用于我的电路板，我会尝试找出另一种方法，或者如果我不能让它工作，可能会得到一个兼容的电路板。



以下为原文

Thanks for the response,
 
I currently have HDMI working on this board by modifying Digilent's HDMI example project, which uses their own DVI receiver/transmitter cores. However their cores seem to block the audio data in the HDMI stream, whereas the Xilinx HDMI core can extract the audio data and output it as I2S. Since it doesn't work with my board I'll try and figure out another way to do it, or maybe get a compatible board if I can't get it to work.

嗨@aytli，
是的我不认为你可以使用ADV7611获得音频。
如果关于这个主题的一切都很清楚，你能否将回复标记为关闭主题的解决方案？
谢谢
FlorentProduct应用工程师 -  Xilinx技术支持EMEA ------------------------------------------
--------------------------------------------------
----------------------------不要忘记回复，kudo，并接受作为解决方案。



以下为原文

Hi @aytli,
 
Yes I do not think you can get the audio with the ADV7611.
 
If everything is clear for you on this subject, could you kindly mark a response as solution to close the topic?
 
Thanks
Florent
Product Application Engineer - Xilinx Technical Support EMEA
------------------------------------------------------------------------------------------------------------------------
Don't forget to reply, kudo, and accept as solution.