[问答]

STM32F103连接到HTS221传感器没有得到正确的温度和湿度值

2017 传感器 STM32

问答对人有帮助，内容完整，我也想知道答案 0 你好，我试图将我的STM32F103连接到HTS221传感器，但我没有得到正确的温度和湿度值。 HTS221_Driver.c从07/04/2014开始的1.0.0版本到目前为止我做了什么：我错过了什么吗？请帮助我，我检查了很多代码示例，但大多数只处理I2C。 Thx提前！亚历山大＃hts221＃stm32f10x 以上来自于谷歌翻译以下为原文 Hello, i tried to connect my STM32F103 to a HTS221 sensor, but I do not get correct values for temperature and humidity. HTS221_Driver.c has version 1.0.0 from 07/04/2014 What I did so far: 01. ... 02. HTS221_Set_PowerDownMode(HTS221_SET); // Tried with HTS221_RESET as well 03. ... // Do other stuff for ~10ms 04. uint8_t deviceId; 05. HTS221_Get_DeviceID(&deviceId); // successfully returns 0xbc 06. HTS221_StartOneShotMeasurement(); 07. HTS221_BitStatus_et humidityStatus = HTS221_RESET, temperatureStatus = HTS221_RESET; 08. while (temperatureStatus == HTS221_RESET) { 09. HTS221_Get_DataStatus(&humidityStatus, &temperatureStatus); 10. } 11. HTS221_Get_Temperature(&tempTemperature); 12. while (humidityStatus == HTS221_RESET) { 13. HTS221_Get_DataStatus(&humidityStatus, &temperatureStatus); 14. } 15. HTS221_Get_Humidity(&tempHumidity); 16. HTS221_DeActivate(); 17. humidity = ((float) tempHumidity / 10); // Result is 100% 18. temperature = ((float) tempTemperature / 10); // Result is 127�C Did I missed anything? Please help me, I checked a lot of code samples but most of them deal with I2C only. Thx in advance! Alexander #hts221 #stm32f10x 0
2018-12-3 09:47:36　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × wang21cj 该类别下有 44 个回答。邀请回答新星之火12138 该类别下有 41 个回答。邀请回答 chm5 该类别下有 39 个回答。邀请回答 hgimtk 该类别下有 33 个回答。邀请回答 HengDu 该类别下有 30 个回答。邀请回答 hwp0415229 该类别下有 28 个回答。邀请回答 jghgfdssas 该类别下有 28 个回答。邀请回答颜刚YanG 该类别下有 26 个回答。邀请回答可口可甜该类别下有 26 个回答。邀请回答 kingnet6688 该类别下有 26 个回答。邀请回答 kingnet9999 该类别下有 25 个回答。邀请回答 jenny042 该类别下有 25 个回答。邀请回答 andyfly7 该类别下有 25 个回答。邀请回答麻酱该类别下有 25 个回答。邀请回答 zyh34997 该类别下有 25 个回答。邀请回答柱子图宁该类别下有 25 个回答。邀请回答云汉007 该类别下有 24 个回答。邀请回答 ggfvxv 该类别下有 24 个回答。邀请回答 heks 该类别下有 24 个回答。邀请回答 iyfhnvbn 该类别下有 24 个回答。邀请回答举报李皓茗相关推荐 • 在HTS221传感器中没有得到正确的湿度数据 2846 • HTS221湿度和温度传感器的I2C地址是多少？ 2839 • hts221返回0xAE 2295 • HTS221湿度超过100％ 1090 • HTS221通过SPI，软重启后无法写入寄存器 1166 • 如何通过STM32WB55微控制器实现传感器读取？ 301 • 长时间暴露在空气中后湿度传感器的HT221功能故障 1167 • 无法使STM32F205的SPI通信正常工作 3219 • HTS221有些校准系数是负的 2980 • 树莓派和HTS221芯片是怎样进行连接的 1244 1个回答

答案对人有帮助，有参考价值 0 嗨，您可以尝试在HTS221_Set_PowerDownMode指令后读取CTRL_REG1（0x20h）吗？什么是读取值？请记住，驱动程序中的HTS221_ReadReg和HTS221_WriteReg指令必须使用SPI重新映射，而HTS221 SPI则需要3线。您是否检查过设备是否正确读取和写入SPI级别？问候安东内拉以上来自于谷歌翻译以下为原文 Hi, Can you try to read the CTRL_REG1 (0x20h) after the HTS221_Set_PowerDownMode instruction? What is the read value? Keep in mind that HTS221_ReadReg and HTS221_WriteReg instructions in the driver, have to be remapped with functions using SPI and that for HTS221 SPI is 3 wires. Do you have check that the device is correctly read and written at level of SPI? Regards Antonella

2018-12-3 09:59:19 评论举报李代三