完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
嗨,我正在尝试使用Ecal方法在E8364B PNA网络分析仪中进行校准,此时只使用2个端口PNA1和PNA2。我将PNA1连接到Ecal的PORTA和PNA2连接到PORTB。
即使所有连接都正确,但错误“+187,无法定位Ecal模块。请确保模块连接到必要的测量端口”不断显示。 相反,每当我连接端口PNA1和TSA1并进行校准时,它就会被校准。 任何人都可以帮我解决这个问题吗? 提前致谢。 以上来自于谷歌翻译 以下为原文 Hi, I am trying to use the Ecal method for calibration in E8364B PNA Network Analyzer, just using 2 ports PNA1 and PNA2 at the moment.I am connecting the PNA1 to PORTA of the Ecal and PNA2 to PORTB. Even though all the connections are made properly, the error " +187, Unable to orient Ecal module. Please ensure the module is connected to the necessary measurement ports" keeps showing up. On the contrary, whenever I connect the ports PNA1 and TSA1 and calibrate, its getting calibrated. Can any one help me on this matter ? Thanks in advance. |
|
相关推荐
1个回答
|
|
你好。
根据您引用的端口名称,我觉得您将E8364B与外部测试集的N441x型号一起使用。 该系统的默认“逻辑到物理端口映射”是:1 =“PNA1”,2 =“TS1”,3 =“PNA2”,4 =“TS2”。 每当测试端口的PNA接收器无法测量从连接到该端口的ECal端口反射的信号时,ECal自动定向通常会失败,原因可能是功率太低,或者路径中连接的外部衰减器使其太低,或者 如果有什么东西阻止信号被接收。 如果你有一个简短的或开放的标准,我建议将该标准连接到端口PNA2并进行原始(即未校准)S33测量,看看是否显示出相当数量的反射信号被测量。 或者,您也可以在PNA1和PNA2之间建立直通连接,并查看S31和S13的原始测量结果是否合理(波纹和一定数量的dB向下但显示接收到的信号)。 我的第一个猜测是,右侧的PNA和测试仪之间的一根或多根跳线可能已经松动,扭结或交叉连接而不是预期的连接。 以上来自于谷歌翻译 以下为原文 Hi. Based on the port names that you referenced, it sounds to me like you're using your E8364B together with one of the N441x models of external testset. The default "logical to physical portmapping" for that system is: 1 = "PNA1", 2 = "TS1", 3 = "PNA2", 4 = "TS2". ECal auto-orientation generally fails whenever the PNA receiver for a testport has trouble measuring the signals reflected from the ECal port attached to that port, either because the power is too low, or an external attenuator connected in the path makes it too low, or if somehow something's blocking that signal from being received at all. If you have a short or open standard handy, I'd suggest connecting that standard to port PNA2 and make a raw (i.e. uncalibrated) S33 measurement, and see if that seems to show a decent amount of reflected signal being measured. Alternatively you might also make a thru connection between PNA1 and PNA2 and see if raw measurements of S31 and S13 seem reasonable (ripply and some number of dB down but showing the signal received). My first guess would be that one or more of the jumper cables between the PNA and testset on the righthand side may have gotten loose, kinked or cross-connected versus the intended connections. |
|
|
|
只有小组成员才能发言,加入小组>>
1285 浏览 0 评论
2373 浏览 1 评论
2192 浏览 1 评论
2064 浏览 5 评论
2948 浏览 3 评论
1111浏览 1评论
关于Keysight x1149 Boundary Scan Analyzer
753浏览 0评论
N5230C用“CALC:MARK:BWID?”获取Bwid,Cent,Q,Loss失败,请问大佬们怎么解决呀
926浏览 0评论
1287浏览 0评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-12-23 19:10 , Processed in 1.174978 second(s), Total 46, Slave 40 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号