完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
我最近用LIS3DH加速度计进行了一些测试来测量机器的振动,我遇到了两件事。我正在使用加速度计以1.1Khz的采样率采样512点。我把它设置为正常模式,ODR = 1.3Khz,在512点我有时得到1或2个离群值与其余值非常不同,它似乎随机发生但我不确定来源(图片)附)。
我的第二个问题是关于加速度计的固有频率,因为我在数据表中找不到它。 问候。 #lis3dh-machine#lis3dh 以上来自于谷歌翻译 以下为原文 I have been doing some testings recently with the LIS3DH accelerometer to measure machine vibration, and I have come across 2 things. I am using the accelerometer to sample 512 points at a 1.1Khz sampling rate. I have it set a normal mode, with ODR =1.3Khz, out of the 512 points I sometimes get 1 or 2 outlier points with very different values from the rest, it seems to happen randomly but I am not sure of the source (picture attached). My second question is about the accelerometer's natural frequency as i could not find it in the datasheet. Regards. #lis3dh-machine #lis3dh |
|
相关推荐
2个回答
|
|
什么是传感器配置?你启用了BDU吗?
有关加速度计固有频率的信息无法在论坛上分享。 以上来自于谷歌翻译 以下为原文 What is the sensor configuration? Did you enable BDU? The information about accelerometer's natural frequency cannot be shared on the forum. |
|
|
|
是BDU已启用,BLE(0),HR已禁用。
是否至少可以确认固有频率超过1Khz? 以上来自于谷歌翻译 以下为原文 Yes BDU is enabled, BLE (0), HR disabled. Is it at least possible to confirm that the natural frequency is over 1Khz ? |
|
|
|
只有小组成员才能发言,加入小组>>
请教:在使用UDE STK时,单片机使用SPC560D30L1,在配置文件怎么设置或选择?里面只有SPC560D40的选项
1478 浏览 1 评论
2147 浏览 1 评论
请问是否有通过UART连接的两个微处理器之间实现双向值交换的方法?
1511 浏览 1 评论
2838 浏览 6 评论
5275 浏览 21 评论
367浏览 4评论
560浏览 4评论
在Linux上安装Atollic TRUEStudio的步骤有哪些呢?
283浏览 3评论
使用DMA激活某些外设会以导致外设无法工作的方式生成代码是怎么回事
640浏览 3评论
536浏览 3评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-4-28 02:01 , Processed in 0.622483 second(s), Total 46, Slave 40 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号