完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
大家好,我目前正在使用labview 8.2程序从N5222A PNA微波网络分析仪获取S21数据。
然而,我得到的值是未校正的值(与我关闭校正时在VNA固件上获得的值相同。当我转动CALC:CORR ON时,我仍然得到错误“在校正之前需要校准才能打开校正 “即使我使用安捷伦PNA系列的召回/保存VI来加载校准.csa文件,我仍然可以得到未校正的值。我已经尝试指定通道,加载.cal和.sta文件,但它仍然没有' 同时.csa,.cal和.sta文件在VNA上成功加载,每次都没有任何错误,但它仍然说没有校准并给我未校准的数据。我知道这是因为我改变了。 csa文件名到不在VNA内存中的东西它会给出一个错误,说明文件无法加载。附上我的VI程序框图截图,VI和校准文件。有没有办法通过LabVIEW打开校准或 还有其他方法来解决这个问题吗?谢谢你 你非常喜欢! latestcal.cal1.6 MBlatestcal.csa1.7 MBPNA二进制数据读取SCPI 2 Damian.vi29.1 KB 以上来自于谷歌翻译 以下为原文 Hi everyone, I am currently using the LabVIEW 8.2 program to obtain S21 data from the N5222A PNA Microwave Network Analyzer. However the values that I get are the uncorrected values (same as the values I get on the VNA firmware when I turn correction off. When I turn CALC:CORR ON, I still get the error "Calibration is required before correction can be turned on" and I still get the uncorrected values even after I use the recall/save VI from Agilent PNA series to load the calibration .csa file. I have tried specifying the channel, loading the .cal and .sta files instead but it still doesn't work. Also the .csa, .cal and .sta file is loaded successfully on the VNA without any error each time yet it still says that there is no calibration and gives me the uncalibrated data. I know this because when I change the .csa filename to something that is not in the VNA memory it gives an error saying the file is unable to load. Attached are my VI block diagram screenshot, the VI, and the calibration files. Is there a way to turn on calibration through LabVIEW or are there any other ways for getting around this? Thank you very much! 附件
|
|
相关推荐
1个回答
|
|
我记得你.csa文件......看起来很好。
但是,不是一个labview的家伙,我不知道你在用CALC做什么:PAR:SEL的21_1'命令。 如果你做了CALC:PAR:CAT ?,唯一返回的是CH1_S11_1。 使用SCPI命令控制台手动执行这些命令会返回错误,因为找不到跟踪。 如果删除具有CAL的两个块会发生什么:PAR:SEL和DISP:WIND:FEED? 我很困惑......而且,为了跳上我的肥皂盒,我讨厌labview和任何使用图片的东西(包括VEE)。 我想看文字。 而且,是的,我老了。 以上来自于谷歌翻译 以下为原文 I recalled you .csa file...that seems fine. But, not being a labview guy, I have no idea what you are doing with the CALC:PAR:SEL 's21_1' command. If you do a CALC:PAR:CAT?, the only thing returned is CH1_S11_1. Performing those commands manually using the SCPI command console, returns an error since the trace is not found. What happens if you remove the two blocks that have CAL:PAR:SEL and DISP:WIND:FEED ? I'm confused...and, to jump on my soapbox, I hate labview and anything that uses pictures (incl VEE). I want to see text. And, yes, I am old. |
|
|
|
只有小组成员才能发言,加入小组>>
973 浏览 0 评论
2250 浏览 1 评论
2029 浏览 1 评论
1907 浏览 5 评论
2772 浏览 3 评论
754浏览 1评论
关于Keysight x1149 Boundary Scan Analyzer
549浏览 0评论
N5230C用“CALC:MARK:BWID?”获取Bwid,Cent,Q,Loss失败,请问大佬们怎么解决呀
645浏览 0评论
2431浏览 0评论
1489浏览 0评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-9-6 20:09 , Processed in 1.329003 second(s), Total 76, Slave 60 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191