完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
电子发烧友论坛|
嗨,我想将VL53L0X用于近距离检测物体的应用,尽可能接近几厘米。
如何配置传感器以使用API在近距离获得最佳性能? 我们可以使用更小的VCSEL脉冲吗? #vl53l0x 以上来自于谷歌翻译 以下为原文 Hi, I want to use VL53L0X for an application that will detect objects in close range, as close as possible in the order of a few cm. How to configure the sensor to get maximum performance at close range using the API? Can we use smaller VCSEL pulses? #vl53l0x |
|
相关推荐
1个回答
|
|
|
对于近距离,我们建议使用VL6180。它更便宜,也更简单。
但是如果你真的想使用VL53,请将传感器向后移动一点,这样你就可以保证目标不会接近几厘米。比这更接近,当光从目标反射到传感器,回到目标和传感器时,范围趋于上升。 6180有这个问题,但程度较小。 降低VCSEL的功率或使用较小的持续时间不能很好地工作。功率更低,VCSEL无法可靠地打开并缩短持续时间会导致其他问题。 - 约翰 以上来自于谷歌翻译 以下为原文 For close ranges we recommend the VL6180. It's cheaper and less complex. But if you really want to use the VL53, move the sensor back a bit so you can guarantee the target will come no closer than a few cm. Closer than that the range tends to go up as the light bounces from target to sensor, back to target and senor. The 6180 has this problem but to a smaller degree. Lowering the power to the VCSEL or using a smaller duration doesn't work well. Less power, and the VCSEL doesn't turn on reliably and shortening the duration causes other issues. - john |
|
|
|
|
只有小组成员才能发言,加入小组>>
stm32mp157的异核通信的rpmsg_sdb的m4固件和a7驱动该如何编写?
1447 浏览 0 评论
stm32f103用freertos对一个采样率为1kHz的传感器,进行采样,数据出差
1494 浏览 0 评论
请教:在使用UDE STK时,单片机使用SPC560D30L1,在配置文件怎么设置或选择?里面只有SPC560D40的选项
3641 浏览 1 评论
3834 浏览 1 评论
请问是否有通过UART连接的两个微处理器之间实现双向值交换的方法?
2454 浏览 1 评论
STM32H7打开DCache后,出现了串口接收信息为空的现象,是哪里出了问题?
727浏览 5评论
用NANO STM32F103RBT6的开发板烧录不了是哪里出了问题?
658浏览 5评论
710浏览 5评论
外部中断触发类型为双边沿触发,进入中断回调后有什么办法判断该边沿是上升沿还是下降沿?
940浏览 5评论
STM32L071CBT6低温环境下无法正常工作是什么原因引起的?
744浏览 5评论
/9
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2025-12-1 18:15 , Processed in 0.728898 second(s), Total 74, Slave 57 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191

淘帖
5232