[问答]

U-Boot 2018.03不能用U盘烧写是为什么？

1436 u-boot

问答对人有帮助，内容完整，我也想知道答案 0 U-Boot 2018.03 (Aug 15 2019 - 02:30:28 +0000) SoC: LS1046AE Rev1.0 (0x87070010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz Bus: 700 MHz DDR: 2100 MT/s FMAN: 800 MHz Reset Configuration Word (RCW): 00000000: 0e150012 10000000 00000000 00000000 00000010: 10405559 40005012 40025000 c1000000 00000020: 00000000 00000000 00000000 00238802 00000030: 20044500 00001102 00000096 00000001 Model: OK1046-C Board: LS1046ARDB, boot from QSPI SERDES Reference Clocks: SD1_CLK1 = 100.00MHZ, SD1_CLK2 = 156.25MHZ SD2_CLK1 = 100.00MHZ, SD2_CLK2 = 100.00MHZ I2C: ready DRAM: Initialzing DDR using fixed setting Configuring DDR for 2100 MT/s data rate 1.9 GiB (DDR4, 32-bit, CL=15, ECC off) DS2460 OK SEC0: RNG instantiated PPA Firmware: Version LSDK-18.06-Forlinx SEC Firmware: 'loadables' present in config loadables: 'trustedOS@1' Using SERDES1 Protocol: 4160 (0x1040) Using SERDES2 Protocol: 21849 (0x5559) MMC: FSL_SDHC: 0 Loading Environment from SPI Flash... SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB OK In: serial Out: serial Err: serial SATA link 0 timeout. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Found 0 device(s). SCSI: Net: SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB Fman1: Uploading microcode version 106.4.18 PCIe0: pcie@3400000 Root Complex: no link PCIe1: pcie@3500000 Root Complex: no link PCIe2: pcie@3600000 Root Complex: no link FM1@DTSEC1, FM1@DTSEC3 [PRIME], FM1@DTSEC4, FM1@DTSEC5, FM1@DTSEC6, FM1@DTSEC10, FM1@TGEC1 Hit any key to stop autoboot: 0 starting USB... USB0: Register 200017f NbrPorts 2 Starting the controller USB XHCI 1.00 USB1: Register 200017f NbrPorts 2 Starting the controller USB XHCI 1.00 USB2: Register 200017f NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... WARN halted endpoint, queueing URB anyway. Unexpected XHCI event TRB, skipping... (fbc7c1b0 00000000 13000000 01008401) BUG at /home/zyh/workspace/RELEASE/OK10xx-linux-fs/flexbuild/packages/firmware/OK10xx-linux-uboot/drivers/u*/host/xhci-ring.c:496/abort_td()! BUG! resetting ... U-Boot 2018.03 (Aug 15 2019 - 02:30:28 +0000) SoC: LS1046AE Rev1.0 (0x87070010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz Bus: 700 MHz DDR: 2100 MT/s FMAN: 800 MHz Reset Configuration Word (RCW): 00000000: 0e150012 10000000 00000000 00000000 00000010: 10405559 40005012 40025000 c1000000 00000020: 00000000 00000000 00000000 00238802 00000030: 20044500 00001102 00000096 00000001 Model: OK1046-C Board: LS1046ARDB, boot from QSPI SERDES Reference Clocks: SD1_CLK1 = 100.00MHZ, SD1_CLK2 = 156.25MHZ SD2_CLK1 = 100.00MHZ, SD2_CLK2 = 100.00MHZ I2C: ready DRAM: Initialzing DDR using fixed setting Configuring DDR for 2100 MT/s data rate 1.9 GiB (DDR4, 32-bit, CL=15, ECC off) DS2460 OK SEC0: RNG instantiated PPA Firmware: Version LSDK-18.06-Forlinx SEC Firmware: 'loadables' present in config loadables: 'trustedOS@1' Using SERDES1 Protocol: 4160 (0x1040) Using SERDES2 Protocol: 21849 (0x5559) MMC: FSL_SDHC: 0 Loading Environment from SPI Flash... SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB OK In: serial Out: serial Err: serial SATA link 0 timeout. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Found 0 device(s). SCSI: Net: SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB Fman1: Uploading microcode version 106.4.18 PCIe0: pcie@3400000 Root Complex: no link PCIe1: pcie@3500000 Root Complex: no link PCIe2: pcie@3600000 Root Complex: no link FM1@DTSEC1, FM1@DTSEC3 [PRIME], FM1@DTSEC4, FM1@DTSEC5, FM1@DTSEC6, FM1@DTSEC10, FM1@TGEC1 Hit any key to stop autoboot: 0 starting USB... USB0: Register 200017f NbrPorts 2 Starting the controller USB XHCI 1.00 USB1: Register 200017f NbrPorts 2 Starting the controller USB XHCI 1.00 USB2: Register 200017f NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... WARN halted endpoint, queueing URB anyway. 能把您的操作过程发一下吗，这些打印信息看不出哪里有问题 => run u_boot Device 0: Vendor: aigo Rev: 1100 Prod: MiniKing Type: Removable Hard Disk Capacity: 15100.0 MB = 14.7 GB (30924800 x 512) ... is now current device Scanning u 0:4... Found U-Boot script /ls1046ardb_update.scr 365 bytes read in 20 ms (17.6 KiB/s) ## Executing script at 80000000 Invalid partition 1 Invalid partition 1 Wrong Image Format for bootm command ERROR: can't get kernel image! SCRIPT FAILED: continuing... Found U-Boot script /boot/ls1046ardb_boot.scr 886 bytes read in 35 ms (24.4 KiB/s) ## Executing script at 80000000 Invalid partition 3 Invalid partition 2 Invalid partition 2 Invalid partition 2 ** Bad Linux ARM64 Image magic! SCRIPT FAILED: continuing... => 0
2022-1-6 06:55:08　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × liutiefu 该类别下有 26 个回答。邀请回答 tigerwang711 该类别下有 20 个回答。邀请回答 ze55me 该类别下有 20 个回答。邀请回答杀狼000 该类别下有 19 个回答。邀请回答 zhuzb0754 该类别下有 19 个回答。邀请回答 YYXIAO 该类别下有 18 个回答。邀请回答冰箱洗衣机该类别下有 18 个回答。邀请回答 jjll652 该类别下有 17 个回答。邀请回答河神大人该类别下有 17 个回答。邀请回答 mede1001 该类别下有 17 个回答。邀请回答安德森大该类别下有 17 个回答。邀请回答 CDCNKA 该类别下有 17 个回答。邀请回答世态薄凉该类别下有 16 个回答。邀请回答熊本熊该类别下有 16 个回答。邀请回答 YOYOOO 该类别下有 16 个回答。邀请回答麻酱该类别下有 16 个回答。邀请回答 szj0213 该类别下有 15 个回答。邀请回答梅利号该类别下有 15 个回答。邀请回答 vinww特烦恼该类别下有 15 个回答。邀请回答 723662364d 该类别下有 15 个回答。邀请回答举报剪刀脚相关推荐 • 为什么U-BOOT烧裸板不能用了？ 662 • 关于U-boot的问题？ 2911 • DM8168 U-Boot烧写问题 3113 • IPNC_DM368 U-Boot和UBL烧写 2240 • 如何解决使用JLINK烧写u-boot报错问题？ 1496 • 关于DM8168 U-boot烧写 1841 • LS1012A开发板如何更新u-boot开发环境呢 1146 • 烧写u-boot到NAND Flash 1920 • u-boot烧写bin文件请问Address:30000000h这个地址是指什么地址？ 3237 • 为什么我用U-boot烧写nand有些文件烧不进去？ 1797 1个回答

答案对人有帮助，有参考价值 0 您用的U盘是手册上说的U 盘的第一个分区为 FAT32 且大于 4G吗您换个U盘试试吧

2022-1-6 09:50:24 评论举报张琳