28377AD采样时结果寄存器值波动较大

5163 寄存器

问答对人有帮助，内容完整，我也想知道答案 0 如图里面所示，无论我是在ID端口输入恒定电压，还是直接在A0端口输入，结果寄存器ADCRESULT0的数一直都在波动，波动值大概有100左右，偶尔还会发生突变，变成接近0或者4095，我用的是12位AD模式，用16位的话波动值更大，用示波器检测电源信号，看到电源只有几毫伏的波动，所以一直不知道是哪出问题了，下面是AD的配置程序，还望大神们答疑解惑 void ConfigureADC(void) { EALLOW; //write configurations AdcaRegs.ADCCTL2.bit.PRESCALE = 6; //set ADCCLK divider to /4 AdcbRegs.ADCCTL2.bit.PRESCALE = 6; //set ADCCLK divider to /4 AdcSetMode(ADC_ADCA, ADC_RESOLUTION_12BIT, ADC_SIGNALMODE_SINGLE); AdcSetMode(ADC_ADCB, ADC_RESOLUTION_12BIT, ADC_SIGNALMODE_SINGLE); //Set pulse positions to late AdcaRegs.ADCCTL1.bit.INTPULSEPOS = 1; AdcbRegs.ADCCTL1.bit.INTPULSEPOS = 1; //power up the ADCs AdcaRegs.ADCCTL1.bit.ADCPWDNZ = 1; AdcbRegs.ADCCTL1.bit.ADCPWDNZ = 1; //delay for 1ms to allow ADC time to power up DELAY_US(1000); EDIS; } void SetupADC(void) { Uint16 acqps; //determine minimum acquisition window (in SYSCLKS) based on resolution if(ADC_RESOLUTION_12BIT == AdcaRegs.ADCCTL2.bit.RESOLUTION){ acqps = 14; //75ns } else { //resolution is 16-bit acqps = 63; //320ns } //Select the channels to convert and end of conversion flag //ADCA EALLOW; AdcaRegs.ADCSOC0CTL.bit.CHSEL = 0; //SOC0 will convert pin A0 AdcaRegs.ADCSOC0CTL.bit.ACQPS = acqps; //sample window is acqps + 1 SYSCLK cycles AdcaRegs.ADCSOC0CTL.bit.TRIGSEL = 1; //这里设置1为timer0中断，设置0为软件中断 AdcaRegs.ADCSOC1CTL.bit.CHSEL = 1; //SOC1 will convert pin A1 AdcaRegs.ADCSOC1CTL.bit.ACQPS = acqps; //sample window is acqps + 1 SYSCLK cycles AdcaRegs.ADCSOC1CTL.bit.TRIGSEL = 1; //这里设置1为timer0中断，设置0为软件中断 AdcaRegs.ADCSOC2CTL.bit.CHSEL = 2; //SOC1 will convert pin A1 AdcaRegs.ADCSOC2CTL.bit.ACQPS = acqps; //sample window is acqps + 1 SYSCLK cycles AdcaRegs.ADCSOC2CTL.bit.TRIGSEL = 1; //这里设置1为timer0中断，设置0为软件中断 AdcaRegs.ADCSOC3CTL.bit.CHSEL = 3; //SOC1 will convert pin A1 AdcaRegs.ADCSOC3CTL.bit.ACQPS = acqps; //sample window is acqps + 1 SYSCLK cycles AdcaRegs.ADCSOC3CTL.bit.TRIGSEL = 1; //这里设置1为timer0中断，设置0为软件中断 AdcaRegs.ADCSOC4CTL.bit.CHSEL = 4; //SOC1 will convert pin A1 AdcaRegs.ADCSOC4CTL.bit.ACQPS = acqps; //sample window is acqps + 1 SYSCLK cycles AdcaRegs.ADCSOC4CTL.bit.TRIGSEL = 1; //这里设置1为timer0中断，设置0为软件中断 AdcaRegs.ADCSOC5CTL.bit.CHSEL = 5; //SOC1 will convert pin A1 AdcaRegs.ADCSOC5CTL.bit.ACQPS = acqps; //sample window is acqps + 1 SYSCLK cycles AdcaRegs.ADCSOC5CTL.bit.TRIGSEL = 1; //这里设置1为timer0中断，设置0为软件中断 //ADCB AdcbRegs.ADCSOC0CTL.bit.CHSEL = 0; //SOC0 will convert pin B0 AdcbRegs.ADCSOC0CTL.bit.ACQPS = acqps; //sample window is acqps + 1 SYSCLK cycles AdcbRegs.ADCSOC0CTL.bit.TRIGSEL = 1; //这里设置1为timer0中断，设置0为软件中断 AdcbRegs.ADCSOC1CTL.bit.CHSEL = 1; //SOC1 will convert pin B1 AdcbRegs.ADCSOC1CTL.bit.ACQPS = acqps; //sample window is acqps + 1 SYSCLK cycles AdcbRegs.ADCSOC1CTL.bit.TRIGSEL = 1; //这里设置1为timer0中断，设置0为软件中断 AdcbRegs.ADCSOC2CTL.bit.CHSEL = 2; //SOC1 will convert pin B1 AdcbRegs.ADCSOC2CTL.bit.ACQPS = acqps; //sample window is acqps + 1 SYSCLK cycles AdcbRegs.ADCSOC2CTL.bit.TRIGSEL = 1; //这里设置1为timer0中断，设置0为软件中断 AdcbRegs.ADCSOC3CTL.bit.CHSEL = 3; //SOC1 will convert pin B1 AdcbRegs.ADCSOC3CTL.bit.ACQPS = acqps; //sample window is acqps + 1 SYSCLK cycles AdcaRegs.ADCSOC3CTL.bit.TRIGSEL = 1; //这里设置1为timer0中断，设置0为软件中断 } void AdcSetMode(Uint16 adc, Uint16 resolution, Uint16 signalmode) { Uint16 adcOffsetTrimOTPIndex; //index into OTP table of ADC offset trims Uint16 adcOffsetTrim; //temporary ADC offset trim //re-populate INL trim CalAdcINL(adc); if(0xFFFF != ((Uint16)GetAdcOffsetTrimOTP)){ //offset trim function is programmed into OTP, so call it //calculate the index into OTP table of offset trims and call //function to return the correct offset trim adcOffsetTrimOTPIndex = 4adc + 2resolution + 1signalmode; adcOffsetTrim = (GetAdcOffsetTrimOTP)(adcOffsetTrimOTPIndex); } else { //offset trim function is not populated, so set offset trim to 0 adcOffsetTrim = 0; } //Apply the resolution and signalmode to the specified ADC. //Also apply the offset trim and, if needed, linearity trim correction. switch(adc){ case ADC_ADCA: AdcaRegs.ADCCTL2.bit.RESOLUTION = resolution; AdcaRegs.ADCCTL2.bit.SIGNALMODE = signalmode; AdcaRegs.ADCOFFTRIM.all = adcOffsetTrim; if(ADC_RESOLUTION_12BIT == resolution){ //12-bit linearity trim workaround AdcaRegs.ADCINLTRIM1 &= 0xFFFF0000; AdcaRegs.ADCINLTRIM2 &= 0xFFFF0000; AdcaRegs.ADCINLTRIM4 &= 0xFFFF0000; AdcaRegs.ADCINLTRIM5 &= 0xFFFF0000; } break; case ADC_ADCB: AdcbRegs.ADCCTL2.bit.RESOLUTION = resolution; AdcbRegs.ADCCTL2.bit.SIGNALMODE = signalmode; AdcbRegs.ADCOFFTRIM.all = adcOffsetTrim; if(ADC_RESOLUTION_12BIT == resolution){ //12-bit linearity trim workaround AdcbRegs.ADCINLTRIM1 &= 0xFFFF0000; AdcbRegs.ADCINLTRIM2 &= 0xFFFF0000; AdcbRegs.ADCINLTRIM4 &= 0xFFFF0000; AdcbRegs.ADCINLTRIM5 &= 0xFFFF0000; } break; case ADC_ADCC: AdccRegs.ADCCTL2.bit.RESOLUTION = resolution; AdccRegs.ADCCTL2.bit.SIGNALMODE = signalmode; AdccRegs.ADCOFFTRIM.all = adcOffsetTrim; if(ADC_RESOLUTION_12BIT == resolution){ //12-bit linearity trim workaround AdccRegs.ADCINLTRIM1 &= 0xFFFF0000; AdccRegs.ADCINLTRIM2 &= 0xFFFF0000; AdccRegs.ADCINLTRIM4 &= 0xFFFF0000; AdccRegs.ADCINLTRIM5 &= 0xFFFF0000; } break; case ADC_ADCD: AdcdRegs.ADCCTL2.bit.RESOLUTION = resolution; AdcdRegs.ADCCTL2.bit.SIGNALMODE = signalmode; AdcdRegs.ADCOFFTRIM.all = adcOffsetTrim; if(ADC_RESOLUTION_12BIT == resolution){ //12-bit linearity trim workaround AdcdRegs.ADCINLTRIM1 &= 0xFFFF0000; AdcdRegs.ADCINLTRIM2 &= 0xFFFF0000; AdcdRegs.ADCINLTRIM4 &= 0xFFFF0000; AdcdRegs.ADCINLTRIM5 &= 0xFFFF0000; } break; } } /* * Loads INL trim values from OTP into the trim registers of the specified ADC. * Use only as part of AdcSetMode function, since linearity trim correction * is needed for some modes. / void CalAdcINL(Uint16 adc) { switch(adc){ case ADC_ADCA: if(0xFFFF != ((Uint16)CalAdcaINL)){ //trim function is programmed into OTP, so call it (CalAdcaINL)(); } else { //do nothing, no INL trim function populated } break; case ADC_ADCB: if(0xFFFF != ((Uint16)CalAdcbINL)){ //trim function is programmed into OTP, so call it (CalAdcbINL)(); } else { //do nothing, no INL trim function populated } break; case ADC_ADCC: if(0xFFFF != ((Uint16)CalAdccINL)){ //trim function is programmed into OTP, so call it (CalAdccINL)(); } else { //do nothing, no INL trim function populated } break; case ADC_ADCD: if(0xFFFF != ((Uint16)CalAdcdINL)){ //trim function is programmed into OTP, so call it (CalAdcdINL)(); } else { //do nothing, no INL trim function populated } break; } } 复制代码* 0 微信截图_20190723100314.png (252.87 KB, 下载次数: 1) 已退回4积分
2019-7-23 10:19:52　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × 柑橘与柠檬该类别下有 19 个回答。邀请回答 jinyi7016 该类别下有 11 个回答，其中被选为最佳答案 2 次。邀请回答 ruanjianming 该类别下有 11 个回答。邀请回答翟荣会该类别下有 10 个回答。邀请回答 24不可说该类别下有 9 个回答，其中被选为最佳答案 9 次。邀请回答云中月1 该类别下有 8 个回答。邀请回答武-之-魂该类别下有 8 个回答。邀请回答大蜜该类别下有 8 个回答。邀请回答 dsphahaha 该类别下有 8 个回答。邀请回答 zercola 该类别下有 8 个回答。邀请回答 zuqiuxiaozi_srx 该类别下有 8 个回答。邀请回答陈该类别下有 8 个回答。邀请回答 sunyu817 该类别下有 7 个回答。邀请回答北纬该类别下有 7 个回答。邀请回答 lz_1995 该类别下有 7 个回答。邀请回答王立峰该类别下有 7 个回答。邀请回答 xxdjx0206 该类别下有 7 个回答。邀请回答 pannybei888 该类别下有 7 个回答。邀请回答士心甬力xzy 该类别下有 6 个回答。邀请回答 forlovefy 该类别下有 6 个回答。邀请回答举报李方旭相关推荐 • DSP**的AD采样口寄存器的值一直波动这是为什么呢 4452* • DSP**的AD采样口输入的模拟电压是稳定不变的，然后采样回去以后，结果寄存器的值一直波动这是为什么呢 4131* • 采样AD7792进行电压采集，更新速率的改变对采集到的幅值影响很大怎么解决？ 515 • AD2S1210的速度检测波动大 2655 • XMC1404ADC端口P2.5接到3.3V进行采样结果寄存器中的值为3270 3049 • TMS320F28377D的CLA读写寄存器失败是什么原因？ 3240 • 调用ad7193单次采样函数前后，读取的配置寄存器值不一样 4894 • 28377D 的DMA是否指出对DAC数据写入 16839 • AD7792转换结果波动大 4728 • ADE7880存放采样数据的寄存器是整型的吗？ 5019 1个回答

答案对人有帮助，有参考价值 0 jnz就是ZF=0时才实现跳转，至于jz/jnz这些跳转，我们这里可以暂时不用管，以后会列举出所有的跳转再慢慢对比。

2019-9-19 14:09:10 评论举报小伍