完善资料让更多小伙伴认识你，还能领取20积分哦， 立即完善>
3天内不再提示
电子发烧友论坛|
有可能获得PICTSTARP PLUS的固件的最后版本吗？更重要的是，PICSTARP PLUS甚至支持在新的MPLAB X上吗？如果不是，什么取代了PICSTAR+？什么是替换方案？哈珀
以上来自于百度翻译 以下为原文 Is it possible to get the very last released version of the firmware for the PICTSTART PLUS? More importanty, is the PICSTART PLUS even supported on the new MPLAB X? If not, what replaced the PICSTART+? What all are the replacement options? Al Harper 
0
|
|
相关推荐
16个回答
|
|
|
也许，在Microchip网站上的某个地方。我记得，最后一个固件需要对PicScript PLUS进行硬件修改。Microchip不再需要一个低成本的程序员来插入芯片。PICKIT 3是低成本版本，但它只是为在电路内编程而设计的。如果你不想在PIC电路中编程，那就很容易在一个Velo板上连接一个插座。
以上来自于百度翻译 以下为原文 Probably, somewhere on the Microchip website. As I recall, the LAST firmware required a hardware modification to the PICSTART PLUS. No. Microchip no longer have a low cost programmer that you insert the chip into. The PICkit 3 is the low cost version, but it's just designed for doing in-circuit programming. It's fairly easy to wire up a socket on a bit of vero-board if you don't want to program your PIC in circuit. |
|
|
|
|
|
你好，在MPLAB X中不支持PICSTARP PLUS。需要哪些设备编程？PICSTARP Plus确实用OTP内存编程了一些非常老的图片。如果你需要编写这样的老照片，只有PM3能做到这一点。
以上来自于百度翻译 以下为原文 Hi, PICSTART Plus is not supported in MPLAB X. which devices do you need to program ? PICSTART PLUS did program some very old PICs with OTP memory. If you need to program such old PICs only PM3 can do this now. Regards |
|
|
|
|
|
PIC Stand Plus与MPLA8892一起工作，它可能与MPLABX的早期版本一起工作。
以上来自于百度翻译 以下为原文 The PIC Start Plus works with Mplab 8.92. It is possible it worked with early versions of MplabX. witch means stick with V8.92 |
|
|
|
|
|
我在认真考虑销售我的PICSTAR+，并用ZIF适配器获得一个PICTIT3。
以上来自于百度翻译 以下为原文 I'm seriously thinking about selling both my PICSTART+'s and getting a PicKit3 with the zif adapters. Al |
|
|
|
|
|
嗨，有一个特定的ZIF适配器，它可以与PICTIT3一起使用。我喜欢它，因为你可以把ICSP连接（电线）放在你喜欢的任何针上，甚至调整铁芯的电压等等。：HTTP://www. MigCHIPInt.t/CufftSexCH..ASPX？关键字= AC162042-2SO，它可以与几乎所有的PICS一起使用，而不需要任何PCB在某些PSP上提供必要的电压。
以上来自于百度翻译 以下为原文 Hi, There is a specific ZIF adapter which can be used with Pickit3. I like it because you can put the ICSP connections (wires) on any pin you like and even adjust voltages for core etc... : http://www.microchipdirect.com/ProductSearch.aspx?Keywords=AC162049-2 So it can be used with almost all PICs without making any PCB to supply the necessary voltages on some pins Regards |
|
|
|
|
|
PICTIT3不会对一些非常老的图片进行编程。这就是为什么我必须打破PIC开始加
以上来自于百度翻译 以下为原文 The PICKit3 will not program some very old PICs. That is why I had to break out the PIC Start Plus |
|
|
|
|
|
我需要编程一个有PIC 12C 508 SO8的旧产品，我有HEXFILE。有可能用Poice Stand Plus和MPLAB编程12C508电路吗？PockStaskPlus是为选择16/17而没有选择12C508，但如果ID可以是进口的，可能使用SO8剪辑连接到Socket Stus Plus上的套接字。谢谢您的任何想法。
以上来自于百度翻译 以下为原文 I need to program an old product which have the PIC 12C 508 SO8, I have the hexfile. Is it possible to program the 12C508 in circuit using PICK START PLUS and MPLab? Pick Start Plus is made for PICK 16/17 and no selection for 12C508 but maybe if an ID could be importet. Possibly using a SO8 clip connected to the socket on the Pick Start Plus. Thanks for any idea. |
|
|
|
|
|
MPLAB 8…92报告12C508可以由PICSTARP PLUS，Pro MARK II，或者PM3编程。你看哪里有12C508的“没有选择”？你更大的问题是12C508是一个一次性可编程设备。你不能擦除和重新编程现有的部分，你只能编程一个空白部分。鉴于此，用一个较新的PIN兼容部分替换它要容易得多，但是你需要访问原始源来重新编译/装配新设备。
以上来自于百度翻译 以下为原文 MPLAB 8..92 reports that a 12C508 can be programmed by a PICSTART PLUS, a PRO MATE II, or a PM3. Where are you looking that has "no selection" for a 12C508? You're bigger problem is that the 12C508 is a one time programmable device. You cannot erase and reprogram an existing part, you can only program a blank part. Given that, it would be a lot easier to replace it with a newer pin-compatible part, but you would need access to the original source to recompile/assemble for the new device. |
|
|
|
|
|
嗨，Eldar，如果你去PIC12C508页面，你会发现唯一支持PIC12C508的程序员是PM3……如果你只需要编程一个设备，那么你需要在因特网上搜索一个廉价程序员的原理图：http://www-ARAROR.COM//RSTEVEW/PULL/Pgmrs /PIC/JensMadsen /N。EWPICH
以上来自于百度翻译 以下为原文 Hi Eldar, If you go to the PIC12C508 page you'll see that the only programmer still supporting the PIC12C508 is the PM3... If you just need to program a single device then you need to search on internet the schematics of a cheap programmer : http://www.armory.com/~rstevew/Public/Pgmrs/PIC/JensMadsen/newpic.htm Regards |
|
|
|
|
|
我可以确认你可以用PICSTART PLUS（带有FLASH）和MPLAB V892 I编程PIC12C508。最近，程序只列出可用的设备。我假设PM2也可以工作。
以上来自于百度翻译 以下为原文 I can confirm the you can Program a PIC12C508 with a PickStart-Plus (with Flash) and Mplab V8.92 I programmed some recently. The Page is problly only listing Available equipment. I assume a PM2 would also work. |
|
|
|
|
|
每个人似乎都没有注意到，OP似乎想重新编程现有的芯片在电路中。不可能与OTP设备，除非在非常具体的情况下，只有“1”位变为“0”。
以上来自于百度翻译 以下为原文 Everyone seems to have missed that the OP appears to want to reprogram an existing chip in circuit. Not possible with an OTP device, except in very specific circumstances where only "1" bits are changing to "0". |
|
|
|
|
|
不，他需要购买新的程序，然后用它们来代替董事会的程序。板上的引脚使用不太可能允许电路编程。
以上来自于百度翻译 以下为原文 Nope he needs to buy new ones program then and use them to replace the ones on the board. It is not likely the pin use on the board would allow in circuit Programing. |
|
|
|
|
|
一个小小的狡辩，Eidar Johnsen并不是原来的海报。用户N4IDAW.COX.NET在七月收到了一个解决方案。这个老线程是由Eidar Johnsen（线程JJAKER）复活的，询问有关在电路中重新编程一次可编程部分的相关问题。这也得到了适当的答复。
以上来自于百度翻译 以下为原文 One small quibble, Eidar Johnsen is not the original poster. User n4ida@cox.net received a solution in July. This old thread was resurrected by Eidar Johnsen (The thread jacker) to ask a related question about reprogramming a one-time-programmable part in circuit. This has also received appropriate replies. |
|
|
|
|
|
我不应该说“OP”。事实上，我指的是约翰森，我指出了POST第9版中的OTP问题，但是接下来的两篇文章忽略了这一点。
以上来自于百度翻译 以下为原文 I shouldn't have said "OP". I was in fact referring to Eidar Johnsen. I pointed out the OTP problem in post#9, but the next two posts ignored that. |
|
|
|
|
|
HII正在制作一些旧的板（客户仍然想要）和使用新的IC，所以OTPO应该是好的。在MPLab我有（V 3.01）与Pick Stand加上下拉Mey的设备12C508是不可使用的。我在这里很新，在网站上（看起来很难），我可以找到8.92版下载，这似乎是一个坚持，可能在这里12C508可能被选中。
以上来自于百度翻译 以下为原文 Hi I am making some old boards (which a customer still wants) and using new IC so OTP should be ok. In MPLab I have (V 3.01) with Pick Start Plus the pull down meny for devices the 12C508 is not avalable. I am quite new here where on the website (looks difficult) may I find version 8.92 to download which seem to be the one to stick with and probably here the 12C508 may be selected. |
|
|
|
|
|
|
|
|
|
|
只有小组成员才能发言，加入小组>>
5248 浏览 9 评论
2036 浏览 8 评论
1956 浏览 10 评论
请问是否能把一个ADC值转换成两个字节用来设置PWM占空比？
3217 浏览 3 评论
请问电源和晶体值之间有什么关系吗？PIC在正常条件下运行4MHz需要多少电压？
2264 浏览 5 评论
781浏览 1评论
676浏览 1评论
有偿咨询，关于MPLAB X IPE烧录PIC32MX所遇到的问题
602浏览 1评论
PIC Kit3出现目标设备ID(00000000)与预期的设备ID(02c20000)不匹配。是什么原因
684浏览 0评论
581浏览 0评论
/7 
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 （电路图） 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证：合字B2-20210191
工商网监
湘ICP备2023018690号
1048
评论
淘帖
2227
