完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
电子发烧友论坛|
我正在尝试使用STVP_CmdLine顺序编程14 x STM8S003设备,但是第14个ST-Link不起作用,将程序员转移到集线器上,程序员在板之间移动问题显示程序员全部工作且电路板也很好。
谢谢 卢克 #ST-linkv2 以上来自于谷歌翻译 以下为原文 I am trying to program 14 x STM8S003 devices sequentially using STVP_CmdLine but the 14th ST-Link doesn't work, moving the programmers around on the hub and programmers between boards moves the problem showing the programmers all work and the boards are also fine. Thanks Luke #st-linkv2 |
|
相关推荐
2个回答
|
|
|
简单。
1.像现在一样编程13个设备。 2.关闭计算机。 3.等待12小时。 4.拔掉所有13个链接。 再等12个小时。 6.插入第14个stlink。 7等15分钟。 8.打开电脑并继续编程芯片。 9.完成后,关闭计算机。 10.拔掉第14个stlink 以上来自于谷歌翻译 以下为原文 Easy. 1. Program 13 devices as you would now. 2. Shut down the computer. 3. Wait at 12 hours. 4. Unplug all 13 stlink. 5. Wait another 12 hours. 6. Plug in the 14th stlink. 7 wait 15 minutes. 8. Turn on the computer and proceed to program the chip. 9. Once done, turn off the computer. 10. Unplug the 14th stlink |
|
|
|
|
|
也许使用Virtual Box并拥有一个VM并为每个VM分配一组不同的USB设备。
以上来自于谷歌翻译 以下为原文 Perhaps use Virtual Box and have a couple VM and allocate a different group of USB devices to each. |
|
|
|
|
只有小组成员才能发言,加入小组>>
stm32mp157的异核通信的rpmsg_sdb的m4固件和a7驱动该如何编写?
1453 浏览 0 评论
stm32f103用freertos对一个采样率为1kHz的传感器,进行采样,数据出差
1502 浏览 0 评论
请教:在使用UDE STK时,单片机使用SPC560D30L1,在配置文件怎么设置或选择?里面只有SPC560D40的选项
3649 浏览 1 评论
3842 浏览 1 评论
请问是否有通过UART连接的两个微处理器之间实现双向值交换的方法?
2461 浏览 1 评论
STM32H7打开DCache后,出现了串口接收信息为空的现象,是哪里出了问题?
727浏览 5评论
用NANO STM32F103RBT6的开发板烧录不了是哪里出了问题?
661浏览 5评论
710浏览 5评论
外部中断触发类型为双边沿触发,进入中断回调后有什么办法判断该边沿是上升沿还是下降沿?
941浏览 5评论
STM32L071CBT6低温环境下无法正常工作是什么原因引起的?
745浏览 5评论
/9
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2025-12-2 01:25 , Processed in 0.532610 second(s), Total 44, Slave 37 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191

淘帖
1144