[问答]

请问LCD的1/2，1/3bias是什么意思

16771

问答对人有帮助，内容完整，我也想知道答案 0 这个参数是什么意思？ 0
2018-11-21 09:12:23　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × cong29898 该类别下有 74 个回答。邀请回答 bwerwer 该类别下有 68 个回答。邀请回答尼克wo 该类别下有 46 个回答。邀请回答崇明土匪该类别下有 45 个回答。邀请回答 xieweibin 该类别下有 40 个回答。邀请回答脑洞大赛7 该类别下有 40 个回答。邀请回答 yfdsfqdqd 该类别下有 38 个回答。邀请回答 wjwierw 该类别下有 38 个回答。邀请回答 Arttronix 该类别下有 32 个回答。邀请回答 bgvywerq 该类别下有 25 个回答，其中被选为最佳答案 1 次。邀请回答 easonl 该类别下有 24 个回答。邀请回答 evpt 该类别下有 24 个回答。邀请回答 wyerwwr 该类别下有 24 个回答。邀请回答脑洞大赛20 该类别下有 22 个回答。邀请回答 60user167 该类别下有 22 个回答。邀请回答 keven杨该类别下有 21 个回答。邀请回答 HTJD 该类别下有 20 个回答。邀请回答胡bbs2 该类别下有 19 个回答。邀请回答 ci56789 该类别下有 19 个回答。邀请回答 xiaokanchenfu 该类别下有 19 个回答。邀请回答举报李富贵相关推荐 • lcd驱动波形为什么不能设计成+-vcc到0？ 1154 • lcd驱动波形。 5190 • 使用NANO112的内部电阻模式，显示特别不清晰怎么解决？ 423 • 使用NANO112的内部电阻模式，显示特别不清晰是为什么？ 362 • ADL5523仿真为什么测S（2,1）也有很高的增益？ 2327 • 怎么设置静态LCD驱动程序 1957 • LCD段码屏选择 2617 • 请问LCD的1/2，1/3bias是什么意思？ 13007 • STM8L LCD配置问题 5659 • 用1/2偏压的方式驱动1/3偏压的段码LCD屏出现鬼影，批量操作可行吗？ 3630 1个回答

LCD Bias(LCD 偏置电压)数代表使用了多少个电压参考点来驱动LCD。偏置电压通常由电阻分压网产生。如最底下的图示出了1/5 Bias，使用Vdd=5V，电阻的数量由上表来决定。
电阻器的电阻值由要求的电压参考点和可能的波形失真决定。因为LCD是容性负载，电阻值应当降低以减少失真，或者用更大的显示屏，使用运放来缓冲电压参考点。
The control signals that drive an LCD are AC in nature. The basic configuration of how to generate a waveform to control an LCD are covered in the sections "LCD Multiplex Ratio (above)" and "LCD Static Drive Technology". But to control LCDs with a larger multiplex ratio, we need to provide the waveform generator with multiple bias voltage level points. The resulting waveform sent to the LCD segment/dot control lines and backplane commons will contain a stair-stepped waveform that will maintain specific ac voltages across any given segment/dot to keep it in it's "on" or "off" state (or in a grayscale module, states between those two points). The LCD Bias number (example: 1/5 bias) will indicate how many voltage reference points are created to drive a specific LCD. The table below shows the relationship between the number of driving bias voltages and the display multiplex ratios typically used:

Mux Ratio

Static

1/2

1/3

1/4

1/7

1/8

1/11

1/12

1/14

1/16

1/24

1/32

1/64

Biases

31/2 Bias

41/3 Bias

51/4 Bias

61/5 Bias

The necessary bias voltages are usually generated by the use of a resistor dividing network, and example of which is shown below using Vdd at 5 volts, and the number of resistors in the ladder determined using the table above.The values of the resistors is determined by the required voltage reference points and possible waveform distortion. Because an LCD is a capacitive load, the values should be decreased to decrease distortion, or with larger displays, buffering the voltage reference points with op-amps.