是否可以在具有2个I210 NIC且每个连接到不同交换机的Team中使两个适配器都处于活动状态？

嗨NAS18W，感谢您在英特尔社区中发帖。对于ALB  RLB，不支持连接到不同的交换机。请分享您的预期设置的其他详细信息。
我们或许可以帮助您寻找其他选择。最诚挚的问候，Vince T.Intel客户支持



以下为原文

Hi NAS18W,

Thank you for posting in Intel Communities.

Connecting to different switches is not a supported configuration for ALB  RLB. 

Please share additional details of your intended setup. We might be able to help you look for other options.


Best Regards,

Vince T.
Intel Customer Support




 

嗨文斯。
感谢您的回复。
自发布以来我一直在进行实验，目前正在使用Switch Fault Tolerant团队。
我有一个带有三个单板计算机和两个非托管第2层交换机的机箱。
计算机A上的应用程序需要连接到计算机B＆amp; B上的应用程序。
C.计算机A上的应用程序仅支持每个目标应用程序的单个IP地址。
两个外部设备可以是工作站或管理型交换机。
我正在尝试在计算机B和B上的两个适配器上配置组合。
C在电缆，适配器或交换机故障时提供冗余。
我遇到的问题似乎是组合适配器的状态，这似乎取决于两个交换机是否可以通信。
如果我在交换机1和交换机2之间添加连接或添加两个外部交换机之间的连接，我会得到所需的结果。
如果交换机之间没有连接，则团队中的一个适配器显示为活动状态，另一个适配器显示为非活动状态。
似乎有些时候来自计算机A的连接请求到达计算机B或C上的非活动适配器并且失败并且没有尝试尝试其他路径。
团队合作所需的交换机之间是否存在连接（当没有故障时）？
谢谢，
尼尔，



以下为原文

Hi Vince.
 
Thanks for your reply.
 
I have continued to experiment since posting and am currently working with Switch Fault Tolerant teaming.  I have an enclosure with three single board computers and two unmanaged layer 2 switches.  An application on computer A needs to connect to applications on Computers B & C.  The app on computer A only supports a single IP address for each of the target applications.  The two external devices may be workstations or managed switches.

I am trying to configure teaming on two adapters on computers B & C to provide redundancy in the event of cable, adapter, or switch failure.
 
The problem I am having seems to be the state of the teamed adapters which seems to be dependent on whether the two switches can communicate.  If I add a connection between switch 1 and switch 2 or add two external switches with a connection between them, I get the desired results.  If there is no connection between the switches, one adapter in the team displays as active and the other as inactive.  It appears that some of the time the connection request from computer A comes to the inactive adapter on computer B or C and fails and there is no attempt to try the other path.
 
Is a connection between the switches required for teaming to work (when there are no failures)?
 
Thanks,
Neil,

嗨Neil，您可以尝试在计算机B和C中的Team上手动设置“主”适配器，以避免计算机A连接到非活动适配器。
此设置位于“设备管理器”中“团队”高级属性的“设置”选项卡下的“修改团队”中。假设与交换机1的连接是您的活动链接，计算机A，B和C将通过交换机1进行通信。
1失败，Teaming软件将检测链路故障并激活连接到Switch 2的适配器。希望这有帮助.Regards，Vince T.Intel客户支持



以下为原文

Hi Neil,

You can try to manually set the "primary" adapters on the Team in computer B and C to avoid computer A from connecting to the inactive adapters. This setting is found in the "Modify Team" under the "Settings" tab of the Team advanced properties in Device Manager.

Assuming connection to Switch 1 is your active link, Computer A, B, and C will communicate through Switch 1. If Switch 1 fails, The Teaming software would detect link failure and activate the adapter connecting to Switch 2. 

Hope this helps.


Regards,

Vince T.
Intel Customer Support

您好Neil，如果您能够尝试上述建议，请告诉我们。
谢谢.Regards，Vince T.Intel客户支持



以下为原文

Hi Neil,

Please let us know if you were able to try the above suggestion. Thanks.


Regards,

Vince T.
Intel Customer Support

嗨文斯。
我还没有机会测试它。
应该能够在下周测试该配置。
之后我会更新。
谢谢。
尼尔。



以下为原文

Hi Vince.
 
I haven't had a chance to test it out yet.  Should be able to test that configuration next week.  I will update after that.
 
Thanks.
Neil.