完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
大家好,我正在尝试修复Agilent 34401a数字万用表。
当仪表打开时,所有显示段都会亮起,仪表会发出一声长哔声。 显示屏关闭,没有任何反应。 我的示波器在XLPORST线路上显示~5khz信号。 有关如何从这里继续的任何提示? BR乔纳斯 以上来自于谷歌翻译 以下为原文 Hi all, I'm trying to repair a Agilent 34401a DMM. When the meter is turned on, all the display segments are lit, and the meter gives a single long beep. The display turns off, and nothing happens. My scope shows a ~5khz signal on the XLPORST line. Any hints on how to continue from here? BR Jonas |
|
相关推荐
2个回答
|
|
我最近和我的34401a有同样的问题。
XPONRST信号只有三件事--U553电压调节器,U500微处理器和U501 ASIC。 就我而言,U501失败了。 更换它允许设备启动并将XPONRST信号返回到稳定的5V。 以上来自于谷歌翻译 以下为原文 I recently had the same problem with my 34401a. There are only three things connected to the XPONRST signal - the U553 voltage regulator, the U500 microprocessor, and the U501 ASIC. In my case, U501 had failed. Replacing it allowed the unit to boot and returned the XPONRST signal to a steady 5V. |
|
|
|
dfjsdadxs 发表于 2018-10-11 16:13 嗨crhastre,谢谢你的回复。 我试图打破U500和U501之间的XPONRST信号线,但是当U501断开时它仍然振荡,所以我不认为ASIC是问题所在。 当我接通电表时,我在LO输入和GND之间测量~14.5V,所以我目前正在通过输入电路。 BR乔纳斯 以上来自于谷歌翻译 以下为原文 Hi crhastre, thank you for your reply. I have tried to break the XPONRST signal line between U500 and U501, but it still oscillates, when U501 is disconnected, so I don't think the ASIC is the problem. When I power on the meter, I measure ~14.5V between the LO input and GND, so I'm currently going through the input circuitry. BR Jonas |
|
|
|
只有小组成员才能发言,加入小组>>
2096 浏览 1 评论
1854 浏览 1 评论
1712 浏览 5 评论
2579 浏览 3 评论
将设备连接到PC并通过asic格式读取数据然后我的网络分析仪挂起
1559 浏览 4 评论
502浏览 1评论
关于Keysight x1149 Boundary Scan Analyzer
363浏览 0评论
1410浏览 0评论
N5230C用“CALC:MARK:BWID?”获取Bwid,Cent,Q,Loss失败,请问大佬们怎么解决呀
272浏览 0评论
2257浏览 0评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-4-24 12:33 , Processed in 1.050782 second(s), Total 76, Slave 60 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号