错误：目标设备尚未准备好进行调试

最明显的解决方案是检查它告诉你什么。你有有效的时钟选择使你的芯片运行吗？您选择了调试器实际上连接到的调试PIN吗？您没有提到您正在使用的调试引脚，或者显示了如何设置PIC的配置寄存器，因此我们只能猜测您的问题可能是什么。



      以下为原文

    The most obvious solution is to check what it tells you to.
Do you have  valid clock selection to make your chip run?
Have you selected the debug pins that your debugger us actually connected to?
 
You have not mentioned which debug pins you are using, or shown how you are setting any of the PIC's CONFIG registers, so we can only guess what your problem might be.
 
 

嗨，http://MyCHIPPrdult.COM/TLS2500：StutthTP://MyCHIIPDeave:…LIVE-PFROFRAM STEP1



      以下为原文

    Hi,
 
http://microchipdeveloper.com/tls2500:start
 
http://microchipdeveloper...:live-photoframe-step1
 
Regards
 

大家好，我尝试写在这里避免打开新的讨论…我不能进入调试模式，而我可以正确地编程设备。MPLAB X4.15XC16 1.32 PIC24F04KA200我从PIC24F04KL101迁移，我在运行中使用FRC振荡器。这里我的配置位为PIC24F04KA200：我已经检查硬件连接，是的，我正确使用PGX3（引脚6，7）。我的配置位有什么问题？



      以下为原文

    Hi guys, I try to write here avoiding opening new discussion...
I can't enter in debug mode while I can correctly program device.
MPLAB X 4.15
XC16 1.32
PIC24F04KA200
 
I'm migrating from PIC24F04KL101 where I was running using FRC oscillator.
 
Here my configuration bits for PIC24F04KA200:
 
 


// oscillator 8MHr FRC
#pragma config FNOSC = FRC

// primary oscillator disabled
#pragma config POSCMOD = NONE // Primary Oscillator Configuration bits (Primary oscillator disabled)
#pragma config MCLRE = ON // MCLR Pin Enable bit (MCLR pin enabled; RA5 input pin disabled)
#pragma config OSCIOFNC = ON // CLKO Enable Configuration bit (CLKO output disabled)

// FICD
#pragma config ICS = PGx3 // Reserved (PGC3/PGD3 are used for programming the device)
 
 
int main(void)
{
    OSCCONbits.SOSCEN = 0;  // secondary oscillator disabled
   
    AD1PCFG = 0xFFFF;   // tutti i pin digitali?
    
    // uscita IGBT
    LATBbits.LATB15 = 0;
    TRISBbits.TRISB15 = 0;
    
    
    // spengo i led
    LATBbits.LATB8 = 0;
    LATBbits.LATB9 = 0;
    
    TRISBbits.TRISB8 = 0;
    TRISBbits.TRISB9 = 0;
 

 
 
I already checked hardware connections and YES, I'm correctly using PGx3 (pins 6,7).
So.... what's wrong with my configuration bits?

嗨，你把所有的ICSP信号（5）连接到ICSP连接器吗？你的VDD电压是多少？你使用哪种调试工具？当做



      以下为原文

    Hi,
Did you connect all ICSP signals (5) to the ICSP connector ?
What is your Vdd voltage ?
Which debug tool do you use ?
Regards
 

是的，他说他可以编程设备-只是不调试



      以下为原文

    yep, he says he can program device - just not debug