免费写单片机程序

图片1.png

刚出来工作，一方面有点闲时间，另一方面为了学习。把你们的要求告诉我，在此尽最大努力帮你写程序，免费的哦。。。

2013-5-11 15:56:44

能帮我写语音交互程序吗？硬件：MCU为STC89C52；SYN6288 TTS 语音合成模块；语音识别模块 LD3320芯片非特定语音；SD卡储存。要求：用SD 卡储存语音数据（txt格式）其中每个语音命令有几种对答系统随机选择；可以直接在SD卡中修改语音数据

王皓 · 2013-5-16 04:06:16

{:3:}{:3:}

爱问问 · 2013-5-16 13:00:58

楼主可以看程序不

张杰 · 2013-5-18 16:31:45

楼主好厉害，支持支持

nicholas042 · 2013-5-18 16:44:46

稍微看了下有点吹牛了

芊‘右手卟弃 · 2013-5-18 17:55:03

顶一个~

2013-5-28 14:21:40

***16点阵的字体显示。。。不甚感激

小李 · 2013-5-28 14:47:20

帮我写一个模拟2262的程序

刘炎柱 · 2013-5-28 16:07:29

{:1:}{:1:}

蟹黄堡 · 2013-5-29 21:42:16

唉，楼主不一定会看到我的回帖，但还是说一下我要写的程序，智能水族箱的控制系统设计，用LCD显示，既要显示时间又要显示温度，还要控制氧气泵和加热棒

chenyi · 2013-5-29 21:53:17

看来，楼主要晕了

从小就很乖 · 2013-6-5 18:34:09

可以帮忙看下这个程序为什么有的字不能完全显现啊

#include
#define int8 unsigned char
#define int16 unsigned int
#define int32 unsigned long

int8 flag;
int8 n;
int8 code table[][32]={
{0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/* "  " */
{0x00,0x00,0xff,0x3f,0x00,0x24,0x00,0x00,0xcc,0x33,0x00,0x20,0x00,0x06,0x00,0x2a,0x00,0x12,0x40,0xa2,0x04,0x00,0xe0,0x3f,0x00,0x02,0x40,0x22,0x10,0x22,0x08,0x02},/*"！",32*/
{0x00,0x00,0x00,0x00,0x80,0x01,0x01,0x11,0x02,0x11,0x7c,0x1f,0x40,0x1b,0x40,0x9b,0x40,0x5b,0x40,0x1b,0x7f,0x1f,0x01,0x11,0x01,0x11,0x87,0x11,0x00,0x00,0x00,0x00},/*"亮",0*/
{0x02,0x02,0x04,0x82,0xF8,0x73,0x04,0x20,0x02,0x00,0xE2,0x3F,0x42,0x20,0x82,0x40,0x02,0x40,0xFA,0x3F,0x02,0x20,0x42,0x20,0x22,0x20,0xC2,0x3F,0x02,0x00,0x00,0x00},/*"迎",1*/
{0x00,0x01,0x04,0x02,0x1C,0x0C,0xC0,0x3F,0x1C,0xC0,0x02,0x09,0x02,0x16,0x92,0x60,0x4A,0x20,0x82,0x2F,0x02,0x20,0x0E,0x24,0x00,0x22,0x90,0x31,0x0C,0x20,0x00,0x00},/*"您",2*/
{0x44,0x10,0x44,0x14,0x88,0x54,0x88,0x54,0xD0,0x5F,0x30,0x50,0x60,0x50,0xFE,0x7F,0x40,0x50,0x20,0x90,0xB0,0x9F,0x98,0x92,0x8C,0x94,0x88,0x34,0x80,0x11,0x00,0x00},/*"乘",3*/
{0x82,0x00,0x02,0x01,0x22,0x06,0x22,0x38,0x22,0x04,0x22,0x03,0x22,0x00,0xFE,0xFF,0xA2,0x00,0x22,0x01,0x22,0x02,0x22,0x3C,0x22,0x02,0x02,0x01,0x02,0x00,0x00,0x00},/*"坐",4*/
{0x02,0x00,0x0C,0x00,0xF0,0x3F,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0xA0,0x00,0x60,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x00},/*"广",5*/
{0x80,0x00,0x01,0x07,0x06,0x00,0x18,0x00,0xE0,0xFF,0x00,0x04,0x00,0x03,0x00,0x00,0xFE,0x7F,0x00,0x08,0x00,0x06,0x80,0x01,0x00,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00},/*"州",6*/
{0x00,0x00,0x04,0x20,0x04,0x21,0x04,0x21,0x04,0x21,0x04,0x21,0x04,0x21,0x04,0x21,0x04,0x21,0x04,0x21,0x04,0x21,0x04,0x21,0x04,0x21,0x04,0x20,0x04,0x00,0x00,0x00},/*"三",7*/
{0x20,0x08,0x20,0x86,0x7F,0x60,0x80,0x0F,0x00,0x04,0x00,0x1A,0x00,0xEA,0x00,0x2A,0x00,0x2A,0x00,0x2A,0x00,0x2A,0xF0,0x2B,0x0C,0x28,0x02,0x20,0x0F,0x00,0x00,0x00},/*"汽",8*/
{0x00,0x00,0x80,0x00,0x04,0x01,0x0E,0x02,0x14,0x0C,0x24,0x70,0xC4,0x21,0x8C,0x00,0x08,0x00,0x08,0x70,0x28,0x08,0x1E,0x06,0x0C,0x03,0x80,0x01,0x00,0x01,0x00,0x00},/*"公",9*/
{0x00,0x00,0x00,0x08,0xF8,0x49,0x20,0x49,0x20,0x49,0x20,0x49,0x20,0x49,0x20,0x49,0x20,0x49,0xF0,0x49,0x00,0x48,0x04,0x40,0x02,0x40,0xFC,0x7F,0x00,0x00,0x00,0x00},/*"司",10*/
{0x00,0x00,0x80,0x00,0x04,0x01,0x0E,0x02,0x14,0x0C,0x24,0x70,0xC4,0x21,0x8C,0x00,0x08,0x00,0x08,0x70,0x28,0x08,0x1E,0x06,0x0C,0x03,0x80,0x01,0x00,0x01,0x00,0x00},/*"公",11*/
{0x40,0x00,0x40,0x08,0x41,0x08,0x42,0x08,0x4C,0x08,0xF8,0x7F,0x50,0x08,0x40,0x08,0x40,0x08,0x60,0x08,0xD0,0x7F,0x4C,0x08,0x47,0x08,0x42,0x08,0x40,0x00,0x00,0x00},/*"共",12*/
{0x20,0x08,0x20,0x86,0x7F,0x60,0x80,0x0F,0x00,0x04,0x00,0x1A,0x00,0xEA,0x00,0x2A,0x00,0x2A,0x00,0x2A,0x00,0x2A,0xF0,0x2B,0x0C,0x28,0x02,0x20,0x0F,0x00,0x00,0x00},/*"汽",13*/
{0x20,0x00,0x20,0x20,0x20,0x21,0x20,0x23,0x20,0x25,0x20,0x39,0x20,0xE1,0x20,0x21,0xFF,0x2F,0x20,0x21,0x20,0x21,0x20,0x21,0x20,0x21,0x20,0x21,0x20,0x00,0x00,0x00},/*"车",14*/
{0x00,0x00,0x00,0x00,0x1A,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"，",15*/
{0x00,0x04,0x01,0x04,0x02,0x04,0x04,0x04,0x08,0x04,0x30,0x04,0xC0,0x05,0x00,0xFE,0x80,0x05,0x60,0x04,0x10,0x04,0x0C,0x04,0x06,0x04,0x03,0x04,0x02,0x04,0x00,0x00},/*"大",16*/
{0x00,0x02,0x40,0x0C,0x40,0x08,0x40,0x48,0x40,0x3A,0x40,0x2A,0x42,0x0A,0x41,0x8A,0xFE,0x7A,0x40,0x2B,0x40,0x0A,0x40,0x18,0x40,0xEA,0x40,0x4C,0x40,0x08,0x00,0x00},/*"学",17*/
{0x20,0x08,0x30,0x08,0xE0,0xFF,0x42,0x08,0x4C,0x08,0xF0,0x1F,0x10,0x12,0x1A,0x12,0xF2,0x13,0x04,0x10,0xC8,0xFF,0x30,0x10,0xCC,0x50,0x02,0x37,0x1C,0x12,0x00,0x00},/*"城",18*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x0E,0x14,0x10,0x24,0x10,0x44,0x10,0x84,0x11,0x0C,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"2",0*/
{0x04,0x02,0x44,0x06,0xC4,0x1A,0x48,0xE3,0x48,0x46,0x48,0x00,0x04,0x09,0x04,0x09,0x08,0x09,0xC8,0xFF,0x30,0x09,0x28,0x49,0x44,0x39,0x02,0x29,0x1F,0x01,0x00,0x00},/*"线",19*/
{0x00,0x02,0x02,0x42,0x04,0x42,0x08,0x42,0x30,0x42,0xC0,0x7F,0x00,0x42,0x00,0x42,0x00,0x42,0x00,0x42,0xFE,0x7F,0x00,0x42,0x00,0x42,0x00,0x42,0x00,0x42,0x00,0x00},/*"开",20*/
{0x40,0x04,0x80,0x08,0x00,0x11,0xFF,0xEF,0x00,0x44,0x02,0x10,0x82,0x10,0x82,0x10,0x82,0x90,0xFE,0x7F,0x82,0x50,0x82,0x10,0x82,0x10,0x82,0x10,0x02,0x10,0x00,0x00},/*"往",21*/
{0x00,0x04,0x01,0x04,0x02,0x04,0x04,0x04,0x08,0x04,0x30,0x04,0xC0,0x05,0x00,0xFE,0x80,0x05,0x60,0x04,0x10,0x04,0x0C,0x04,0x06,0x04,0x03,0x04,0x02,0x04,0x00,0x00},/*"大",22*/
{0x00,0x02,0x40,0x0C,0x40,0x08,0x40,0x48,0x40,0x3A,0x40,0x2A,0x42,0x0A,0x41,0x8A,0xFE,0x7A,0x40,0x2B,0x40,0x0A,0x40,0x18,0x40,0xEA,0x40,0x4C,0x40,0x08,0x00,0x00},/*"学",23*/
{0x20,0x08,0x30,0x08,0xE0,0xFF,0x42,0x08,0x4C,0x08,0xF0,0x1F,0x10,0x12,0x1A,0x12,0xF2,0x13,0x04,0x10,0xC8,0xFF,0x30,0x10,0xCC,0x50,0x02,0x37,0x1C,0x12,0x00,0x00},/*"城",24*/
{0x00,0x00,0x00,0x00,0x1A,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"，",25*/
{0x00,0x02,0x00,0x42,0x00,0x32,0xFE,0x23,0x04,0x00,0x08,0x44,0xFF,0x55,0x50,0x55,0x50,0x55,0x50,0xFD,0x52,0x55,0x51,0x55,0xFE,0x55,0x00,0x44,0x00,0x04,0x00,0x00},/*"请",26*/
{0x00,0x01,0x04,0x02,0x1C,0x0C,0xC0,0x3F,0x1C,0xC0,0x02,0x09,0x02,0x16,0x92,0x60,0x4A,0x20,0x82,0x2F,0x02,0x20,0x0E,0x24,0x00,0x22,0x90,0x31,0x0C,0x20,0x00,0x00},/*"您",27*/
{0x82,0x00,0x02,0x01,0x22,0x06,0x22,0x38,0x22,0x04,0x22,0x03,0x22,0x00,0xFE,0xFF,0xA2,0x00,0x22,0x01,0x22,0x02,0x22,0x3C,0x22,0x02,0x02,0x01,0x02,0x00,0x00,0x00},/*"坐",28*/
{0x01,0x08,0xC2,0x08,0x44,0x0F,0x28,0xF8,0x30,0x08,0xCE,0x0F,0x04,0x01,0x00,0x41,0x02,0x41,0x01,0x41,0xFE,0x4F,0x00,0x51,0x00,0x61,0x00,0x41,0x00,0x01,0x00,0x00},/*"好",29*/
{0x42,0x08,0x81,0x08,0xFE,0xFF,0x00,0x09,0x01,0x0A,0x01,0x01,0x02,0x11,0x0C,0x11,0x30,0x11,0xC0,0xFF,0x30,0x11,0x08,0x11,0x06,0x11,0x03,0x11,0x02,0x01,0x00,0x00},/*"扶",30*/
{0x20,0x08,0xC0,0x48,0x00,0x4B,0xFF,0x7F,0x00,0x89,0x9C,0x88,0x00,0x10,0xBC,0x2A,0x82,0xCA,0xC2,0x4A,0xB2,0x5A,0x82,0x6A,0xAE,0x0A,0x90,0x0F,0x0C,0x00,0x00,0x00},/*"稳",31*/
{0x00,0x00,0x00,0x00,0x00,0x00,0xFA,0x0F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"！",32*/
};

void delay(void);
int16 offset;

void main(void)
{
int8 i;
int8 *p;
flag=0x10;
n=0;
TMOD=0x01;
TH0=0xb1;
TL0=0xe0;
ET0=1;
EA=1;
TR0=1;
p=&table[0][0];

while (1)
{
      for (i=0;i<8;i++) //显示左半边屏幕
      {
         P0=*(p+offset+2*i);
         P2=i|0x08; //P2.4=0,P2.3=1 选中U2, 输出扫描码给U6
         delay();
         P0=*(p+offset+2*i+1);
            P2=i|0x10; //P2.4=1,P2.3=0 选中U3, 输出扫描码给U7
         delay();
      }
      for (i=8;i<16;i++)    //显示右半边屏幕
      {
         P0=*(p+offset+2*i);
         P2=(i-8)|0x20; //P2.5=1 P2.4=0, P2.3=0 选中U4,输出扫描码U8
         delay();

         P0=*(p+offset+2*i+1);
         P2=(i-8)|0x40; //P2.6=1 P2.5=0, P2.4=0 选中U5,输出扫描码U9
         delay();
      }
}
}

void delay(void)
{
int16 i;
for (i=0;i<50;i++)
      ;
}

void timer0() interrupt 1 using 3
{
TF0=0;
TH0=0xb1;
TL0=0xe0;
if (n<10)
{
n++;
}
else
{
offset+=2;
if (offset>1100)
         offset=0;
      n=0;
}
}

goodpcb · 2013-6-5 21:00:05

我在想楼主真的能全部包下并完成吗？神人了

xinghx · 2013-11-19 23:06:11

楼主如果还可以写，请帮我写个：用keil
数字时钟的程序（要求用数码管显示时分秒，可调时，有闹钟功能）
可调亮度Led 用变阻器去控制那个led灯的亮度
最好是英飞凌单片机的，51的也行
不胜感激
xinghx@sina.cn 谢谢先

lzbxh123 · 2013-11-20 23:12:37

∮Z打個哈欠发表于 2012-12-14 11:08
跪求楼主帮忙写一个51单片机利用ADC0809分析温度数据并且显示在8位LED上的温度多通道数据采集电路的C程序 ...

我擦，是你啊！

龚旭 · 2013-11-21 14:01:31

scientistzeng · 2013-11-21 14:09:37

是不是真的啊。有一个我觉得很难得单片机控制程序。能不能帮忙。用串口和PC机通讯。可以帮忙不

yuwen · 2013-11-21 20:01:47

呵呵，楼主，能不能帮我看下这个程序，
  #include
***it  out_1=P1^0;    //爆闪输出1
***it out_2=P1^1;    //爆闪输出2
***it  out_3=P1^2;    //爆闪输出3
***it out_4=P1^3;    //爆闪输出4
***it a=P1^2;       //数码管段位a
***it b=P1^6;       //数码管段位b
***it c=P3^6;       //数码管段位c
***it d=P3^0;       //数码管段位d
***it e=P3^1;       //数码管段位e
***it f=P1^0;       //数码管段位f
***it g=P3^4;          //数码管段位g
//unsigned int f=2000;
unsigned int cnt,cout,l,v,m,t; //定义变量
void delay (unsigned int k)       //延时程序
{
  unsigned int i,j;
  for (i=0;i {
   for (j=0;j<=121;j++)
   {;}
  }

}
void init(void)                //初始化
{
PX1=1;
EX1 =1;
IT1 =1;
EA=1;

}

void extern_int1(void)  interrupt 2    //中断按键检测
{
delay(35);
cout++;
if(cout==9)
{
cout=0;
}

}
void IN_SYSTEM_init(void)//定时器初始化
{
TMOD = 0X11;
TH1=-(30000/256);
TL1=-(30000/256);
ET1=1;
TR1=1;
TH0=-(30000/256);
TL0=-(30000/256);
ET0=1;
TR0=1;
EA=1;
}
//***********************************************定时器0中断服务函数
void time0_int (void) interrupt 1
{
TH0=-(30000/256);
TL0=-(30000%256);
  out_1= ~out_1;
out_2=~out_2;
  }
//***************************************************定时器1中断服务函数
void time1_int (void) interrupt 3
{
  TH1=-(30000/256);
TL1=-(30000%256);
  out_3=~out_3;
  out_4=~out_4;
  }
//****************************************************
void k_1(void)             //按键切换
{
switch(cout)
   {
//****************************************************

//**************************************************** 第一种变化，交替闪
  case 1:
  a=b=c=d=e=f=g=1;
  b=c=0;
  delay(200) ;

EX1 =0;
for(cnt=0;cnt<=15;cnt++)
{
out_1=out_2=out_3=out_4=1;
TR1=1;
TR0=0;
delay(80);
}

for(cnt=0;cnt<=15;cnt++)
{
out_1=out_2=out_3=out_4=1;
  TR1=0;
TR0=1;
  delay(80);
}

  EX1 =1;
break;
      //------------------------------------------2渐快闪
case 2:
a=b=c=d=e=f=g=1;
a=b=d=e=g=0;
EX1 =0;
      m+=10;
         if(m>150)  {  m=0; }
         for(t=0;t<=23;t++)
            {
            TR1=0;
               TR0=1;
                  out_1=out_2=out_3=out_4=1;
            delay(150-m);
         }
         delay(150-m);
         for(t=0;t<=23;t++)
         { TR1=1;
               TR0=0;
            out_1=out_2=out_3=out_4=1;
            delay(150-m);
         }
      EX1 =1;
         break;

//**************************************************** 3快全闪，
case 3:
a=b=c=d=e=f=g=1;
a=b=c=d=g=0;
EX1 =0;
         for(t=0;t<=20;t++)
            {
               TR1=1;
            TR0=1;
      delay(100);
            }
            TR1=0;
            TR0=0;
            out_1= 1;
            out_2=1;
            out_3=1;
            out_4=1;
      delay(1000);
   EX1 =1;
break;
//****************************************************4慢全闪
case 4:
   a=b=c=d=e=f=g=1;
   b=c=f=g=0;
   EX1 =0;
for(t=0;t<=20;t++)
            {
               TR1=1;
            TR0=1;
      delay(100);
            }
            TR1=0;
            TR0=0;
            out_1= 1;
            out_2=1;
            out_3=1;
            out_4=1;
      delay(2500);
   EX1 =1;
break;
//****************************************************5全闪
  case 5:
   a=b=c=d=e=f=g=1;
a=c=d=f=g=0;
   EX1 =0;
  TR1=1;
            TR0=1;
               delay(150);

EX1 =1;
break;
//****************************************************6交替闪再全闪
case 6:
a=b=c=d=e=f=g=1;
a=c=d=e=f=g=0;
EX1 =0;
      for(l=0;l<=3;l++)
      {
         for(cnt=0;cnt<=13;cnt++)
         { out_1=out_2=out_3=out_4=1;

         TR1=0;
         TR0=1;
         delay(150);
         }
         for(cnt=0;cnt<=13;cnt++)
         {
                  out_1=out_2=out_3=out_4=1;
            TR1=1;
               TR0=0;
            delay(150);
         }
   }
for(v=0;v<=3;v++)
{
      for(cnt=0;cnt<=10;cnt++)
{
TR1=1;
TR0=1;
delay(150);
}
TR1=0;
TR0=0;
            out_1= 1;
            out_2=1;
            out_3=1;
            out_4=1;

delay(1000);
}
  EX1 =1;
break;

//***************************************************7流水闪烁
case 7:
a=b=c=d=e=f=g=1;
a=b=c=0;
EX1 =0;
               TR1=0;
               out_1=out_2=out_3=out_4=1;
               TR0=0;
      for(t=0;t<=13;t++)
            {

         out_4= ~out_4;
         delay(100);
            }
      for(t=0;t<=13;t++)
            {

            out_3= ~out_3;
            delay(100);
            }
      for(t=0;t<=13;t++)
            {
         out_2= ~out_2;
         delay(100);
            }

      for(t=0;t<=13;t++)
            {
            out_1= ~out_1;
            delay(100);
            }
EX1 =1;
         break;
         //****************************************************8左右交替长闪
case 8:
   a=b=c=d=e=f=g=1;
   a=b=c=d=e=f=g=0;
  EX1 =0;
for(cnt=0;cnt<=15;cnt++)
{
out_1=out_2=out_3=out_4=1;
  TR1=1;
  TR0=0;
delay(300);
}
for(cnt=0;cnt<=15;cnt++)
{
  out_1=out_2=out_3=out_4=1;
TR1=0;
TR0=1;
  delay(300);
}
EX1 =1;
break;
//****************************************************0全灭
   case 0:
      a=b=c=d=e=f=g=1;
      EX1 =0;
            out_1=out_2=out_3=out_4=1;
         TR1=0;
         TR0=0;
      EX1 =1;
      break;
   }
   }

//**************************************************** 主程序

void main (void)
{

init();
IN_SYSTEM_init();
while (1)
{
k_1();

}
}
按键后总是好像要等待一个循环完成才能换到下一个模式里，本想按键后立即换下一个模式,怎么解决？