完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
我试图通过串行接口连接hp34401A万用表但我无法通过自动检测在i o中检测到。当我手动配置设备然后尝试使用直接i o它发出错误801并说出串行接口
没有配置。任何人都可以帮助我吗? 以上来自于谷歌翻译 以下为原文 Im trying to conect a hp34401A Multimeter trough a serial interface but i cannot detect in the io by automatic detection. When i configure manually the device and then try to use direct io it gives out error 801 and says that the serial interface is not configured. Can anyone help me? |
|
相关推荐
9个回答
|
|
是否启用了34401A RS-232接口?
使用34401A,只能启用串行或GPIB IO。 如果使用串行接口,34401A将在上电时短暂显示“RS-232”。 使用前面板菜单键在RS-232和GPIB之间切换。 您是否使用Agilent IO Libraries,Agilent Connection Expert(ACE)进行连接? 以上来自于谷歌翻译 以下为原文 Is the 34401A RS-232 interface enabled? With the 34401A, only the serial or the GPIB IO can be enabled. If you are using the serial interface the 34401A will display "RS-232" briefly when it is powered up. Use the front panel menu keys to switch between RS-232 and GPIB. Are you using the Agilent IO Libraries, Agilent Connection Expert (ACE) to make the connection? |
|
|
|
是的我启用了界面。
我没有使用VEE Pro 7.0,也没有安装ACE。 以上来自于谷歌翻译 以下为原文 Yes i have the interface enabled. No im using the VEE Pro 7.0 and it doesn't have the ACE installed. |
|
|
|
现在程序检测到串口,但我无法发送和IDN查询它总是给出错误811
以上来自于谷歌翻译 以下为原文 Right now the program as detected the serial port, but i cannot send and IDN query it always gives out error 811 |
|
|
|
你好,
您需要安装ACE才能与34401A进行通信。 您在该工具中设置了所有RS-232设置,并安装了与仪器通信所需的基础签证/签名。 您可以在这里免费下载ACE: http://www.keysight.com/find/iosuite 以上来自于谷歌翻译 以下为原文 Hello, You need to install ACE in order to communicate with your 34401A. You set up all of your RS-232 settings in that tool, and it installs the underlying visa/sicl needed for communication with the instrument. You can download ACE here for free: http://www.keysight.com/find/iosuite |
|
|
|
我下载ACE,但即使在ace中我仍然遇到连接错误。
我完成了连接,但在IDN中出现错误,现在我甚至无法获得ACE完成的IDN查询 以上来自于谷歌翻译 以下为原文 I download ACE, but i keep getting a conection error even in ace. I got the connection done, but then got an error in IDN and right now i cant even get a IDN query done by ACE |
|
|
|
任何人都可以帮我解决这个问题吗? 我一直试图解决它2个月,切换计算机,将计算机上的能源切换,因为它似乎出现故障并切换到IEEE-488。 什么可能搞乱连接的提示? 感谢Rui Cordeiro的所有帮助 以上来自于谷歌翻译 以下为原文 Can anyone help me with this problem? I've been trying to solve it for 2 months, switch computers, gonna switch my energy source on the computer cuz it seems to be malfunctioning and switching to IEEE-488. Any tips of what can be messing the connection? Thanks for all the help Rui Cordeiro |
|
|
|
hytgab 发表于 2019-5-31 09:17 您好,您确定ACE和仪器上的RS-232设置是否匹配? 以下是34401A默认值:如果需要,您可以从前面板更改波特率,奇偶校验和数据位。 启动和停止位是固定的。 波特率:9600奇偶校验和数据位:偶数/ 7数据位起始位数:1(固定)停止位数:2(固定)如果您使用的是Windows 7 64位系统,并且您确定已设置 升级RS-232以匹配仪器和ACE,它仍然无法正常工作,看看这篇文章:34970A RS-232困境 以上来自于谷歌翻译 以下为原文 Hello, Did you make sure the RS-232 settings in ACE and on the instrument match up? Here are the 34401A defaults: You can change the Baud rate, parity and databits from the front panel if you want. The Start and Stop bits are fixed. Baud rate: 9600 Parity and Data bits: even/ 7 data bits Number of Start bits: 1 (fixed) Number of stop bits: 2 (fixed) If you are using a windows 7 64 bit system, and you are sure you have set up the RS-232 to match on the instrument and in ACE and it's still not working, have a look at the this post: 34970A RS-232 woes |
|
|
|
4864165sas 发表于 2019-5-31 09:36 是的所有设置都匹配。 我改为HP-IB,现在可以使用了。 但是使用串行接口我无法使用它。 此外,我想与可以帮助我在VEE Pro中编程的人取得联系,因为我真的不知道如何做到这一点,我试图开发一个程序作为项目的一部分 以上来自于谷歌翻译 以下为原文 Yes all the settings are matching. I changed to HP-IB and it works now. But with the serial interface i cant get it to work. Also i would like to get in touch with someone that can help me program in VEE Pro because i dont really know how to do it and im trying to develop a program as part of a project |
|
|
|
我们注意到在Win 7(非管理员帐户)上,ACE实际上并未更改RS-232接口的设置。 必须在设备管理器中手动更改这些设置以查找相关的COM端口。 只要设置与您的仪器匹配,ACE就可以与盒子通信(即BaudRate,Flow Control等)。 以上来自于谷歌翻译 以下为原文 We have noticed that on Win 7 (non admin accounts) ACE does not actually change the settings for the RS-232 interface. These settings must be changed manually in the device manager for COM port in question. ACE can then communicate with the box as long as the settings match your instrument (i.e. BaudRate, Flow Control, ect..) |
|
|
|
只有小组成员才能发言,加入小组>>
1291 浏览 0 评论
2375 浏览 1 评论
2194 浏览 1 评论
2065 浏览 5 评论
2952 浏览 3 评论
1123浏览 1评论
关于Keysight x1149 Boundary Scan Analyzer
758浏览 0评论
N5230C用“CALC:MARK:BWID?”获取Bwid,Cent,Q,Loss失败,请问大佬们怎么解决呀
934浏览 0评论
1294浏览 0评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-12-26 05:56 , Processed in 1.555209 second(s), Total 94, Slave 78 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号