完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
嗨,查看SCPI指南,http://na.tm.agilent.com/fieldfox/help/Programming/webhelp/FFProgrammingHelp.htm看起来SA模式不支持信号发生器/跟踪发生器模式。
换句话说,我无论如何都无法以编程方式使用信号发生器。 你能否证实这是一个限制或我遗失了什么? 如果是限制,是否会在某些时候启用? 我们正在考虑为N9915A订购SA选项,但如果不能以编程方式使用信号发生器,我们就无法真正有效地使用它。 谢谢 以上来自于谷歌翻译 以下为原文 Hi, Looking into the SCPI guide, http://na.tm.agilent.com/fieldfo ... ProgrammingHelp.htm it looks like the SA mode has no support for the Signal Generator / Tracking Generator mode. In other words, I can't see anyway to use the signal generator programmatically. Can you confirm this is a limitation or I am missing something? If it is a limitation, will this be enabled at some point? We are considering ordering the SA option for the N9915A but if the Signal Generator cannot be used programmatically we cannot really make effective use of it. Thanks |
|
相关推荐
4个回答
|
|
> {quote:title = a_rocholl写道:} {quote}>我遗失了什么?
如果是限制,>感谢通常,在带有跟踪发生器的SA中,TG必须与SA的频率相同,因此它可以用作粗略的标量网络分析器。 但N9915A有一个真正的网络分析仪,因此通常用于TG-SA功能。 以上来自于谷歌翻译 以下为原文 > {quote:title=a_rocholl wrote:}{quote} > I am missing something? If it is a limitation, > Thanks Normally, in an SA with a tracking generator, the TG must be at the same frequency as the SA, and so it can be used as a rough Scalar Network Analyzer. But the N9915A has a true network analyzer, so that is normally what one would use for the TG-SA function. |
|
|
|
脑洞大赛9 发表于 2019-3-7 13:33 我的问题不是关于使用VNA或SNA。 我的问题是如何将信号发生器用作其他用途的独立射频源。 这可以在面板上手动完成,但在SCPI命令列表中绝对没有通信。 事实上,就SCPI而言,SG / TG功能根本不可用。 以上来自于谷歌翻译 以下为原文 My question is not about using a VNA or a SNA. My question is how to use the Signal Generator as an independent RF source for other purposes. This can be done manually on the panel but there is absolutely no commnad for that in the SCPI command list. In fact, as far as SCPI is concerned, the SG/TG feature is not available at all. |
|
|
|
S_A_Lucky 发表于 2019-3-7 13:49 跟踪生成器在FieldFox中被称为独立源(我们在大多数情况下尝试使用这两个术语)并且它通过SCPI支持。 这是命令。 http://na.tm.agilent.com/fieldfox/help/Programming/webhelp/A_SA_Mode_Commands.htm#Inrependent独立源启用[:SENSe]:ISOurce:ENABle CW或S / R [:SENSe]:ISOurce:MODE CW 频率[:SENSe]:ISOurce:FREQuency [:CW] Normalize [:SENSe]:ISOurce:NORMalize衰减(功率)N9912A ON [:SENSe]:ISOurce:POWer:ATTenuation Power Level(所有型号除N9912A外)[:SENSe] :ISOurce:POWer Max Power(所有型号除N9912A外)[:SENSe]:ISOurce:POWer:MAXimum Afsi 以上来自于谷歌翻译 以下为原文 The Tracking Generator is referred to as an independent source in FieldFox (we try to use both terms in most cases) and it is supported via SCPI. Here are the commands. http://na.tm.agilent.com/fieldfox/help/Programming/webhelp/A_SA_Mode_Commands.htm#Independent Independent Source Enable [:SENSe]:ISOurce:ENABle CW or S/R [:SENSe]:ISOurce:MODE CW Frequency [:SENSe]:ISOurce:FREQuency[:CW] Normalize [:SENSe]:ISOurce:NORMalize Attenuation (power) N9912A ONLY [:SENSe]:ISOurce:POWer:ATTenuation Power Level (All models EXCEPT N9912A) [:SENSe]:ISOurce:POWer Max Power (All models EXCEPT N9912A) [:SENSe]:ISOurce:POWer:MAXimum Afsi |
|
|
|
dsgdadsad 发表于 2019-3-7 14:08 啊! 独立来源! 这就是我所缺少的,有道理,谢谢。 可以了,好了。 以上来自于谷歌翻译 以下为原文 Ah! Independent Source! That was what I was missing, makes sense, thanks. All set. |
|
|
|
只有小组成员才能发言,加入小组>>
1229 浏览 0 评论
2350 浏览 1 评论
2160 浏览 1 评论
2026 浏览 5 评论
2908 浏览 3 评论
973浏览 1评论
关于Keysight x1149 Boundary Scan Analyzer
707浏览 0评论
N5230C用“CALC:MARK:BWID?”获取Bwid,Cent,Q,Loss失败,请问大佬们怎么解决呀
808浏览 0评论
1230浏览 0评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-11-25 19:09 , Processed in 1.426702 second(s), Total 83, Slave 66 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号