U-Boot 2016.07-00124-g7a8868e-dirty (Feb 21 2017 - 14:12:45 +0800)
CPU: Freescale i.MX7S rev1.2 at 792MHz
CPU: Extended Commercial temperature grade (-20C to 105C) at 52C
Reset cause: POR
Board: WARP7
I2C: ready
DRAM: 512 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
## Resetting to default environment
reading zImage
7407928 bytes read in 99 ms (71.4 MiB/s)
reading imx7d-warp.dtb
38871 bytes read in 11 ms (3.4 MiB/s)
Kernel image @ 0x80800000 [ 0x000000 - 0x710938 ]
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Using Device Tree in place at 83000000, end 8300c7d6
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 4.1.29-00014-g02151e5 (zhou@t430) (gcc version 4.9.1 20140710 (pr7
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Warp i.MX7S Board
Reserved memory: created CMA memory pool at 0x8c000000, size 320 MiB
Reserved memory: initialized node linux,cma, compatible id shared-dma-pool
Memory policy: Data cache writealloc
PERCPU: Embedded 12 pages/cpu @8bb22000 s16960 r8192 d24000 u49152
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: console=ttymxc0,115200 init=/init androidboot.hardware=fred
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 177856K/524288K available (8223K kernel code, 468K rwdata, 2856K rodata)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x80ada15c (11081 kB)
.init : 0x80adb000 - 0x80c0c000 (1220 kB)
.data : 0x80c0c000 - 0x80c81220 ( 469 kB)
.bss : 0x80c84000 - 0x80d0b97c ( 543 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Preemptible hierarchical RCU implementation.
Additional per-CPU info printed with stalls.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
Architected cp15 timer(s) running at 8.00MHz (phys).
clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, ms
sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns
Switching to timer-based delay loop, resolution 125ns
mxc_clocksource_init 3000000
Ignoring duplicate/late registration of read_current_timer delay
clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6s
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 16.0)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
/cpus/cpu@0 missing clock-frequency property
/cpus/cpu@1 missing clock-frequency property
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x80008280 - 0x800082d8
CPU1: failed to come online
Brought up 1 CPUs
SMP: Total of 1 processors activated (16.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
device-tree: Duplicate name in lcdif@30730000, renamed to "display#1"
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911s
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
DDR type is LPDDR3!
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver
gpio-reset mipi-dsi-reset: reset-gpios property missing, or not a single gpio
gpio-reset: probe of mipi-dsi-reset failed with error -22
MU is ready for cross core communication!
mxs-dma 33000000.dma-apbh: initialized
SCSI subsystem initialized
u***core: registered new interface driver u***fs
u***core: registered new interface driver hub
u***core: registered new device driver u***
30800000.aips-bus:u***phy_nop1 supply vcc not found, using dummy regulator
30800000.aips-bus:u***phy_nop2 supply vcc not found, using dummy regulator
i2c i2c-0: IMX I2C adapter registered
i2c i2c-0: can't use DMA
i2c i2c-1: IMX I2C adapter registered
i2c i2c-1: can't use DMA
i2c i2c-2: IMX I2C adapter registered
i2c i2c-2: can't use DMA
i2c i2c-3: IMX I2C adapter registered
i2c i2c-3: can't use DMA
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.20
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
imx rpmsg driver is registered.
Bus freq driver module loaded
futex hash table entries: 512 (order: 3, 32768 bytes)
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
fuse init (API version 7.23)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
backlight supply power not found, using dummy regulator
MIPI DSI driver module loaded
mxc_mipi_dsi_samsung 30760000.mipi-dsi: no reset gpio pin available
30760000.mipi-dsi supply disp-power-on not found, using dummy regulator
mxc_mipi_dsi_samsung 30760000.mipi-dsi: i.MX MIPI DSI driver probed
MIPI DSI driver module loaded
30730000.lcdif supply lcd not found, using dummy regulator
mxc_mipi_dsi_samsung 30760000.mipi-dsi: MIPI DSI dispdrv inited!
mxsfb 30730000.lcdif: registered mxc display driver mipi_dsi_samsung
Console: switching to colour frame buffer device 40x40
mxsfb 30730000.lcdif: initialized
imx-sdma 30bd0000.sdma: no event needs to be remapped
imx-sdma 30bd0000.sdma: loaded firmware 4.2
imx-sdma 30bd0000.sdma: initialized
pfuze100-regulator 0-0008: Full layer: 1, Metal layer: 1
pfuze100-regulator 0-0008: FAB: 0, FIN: 0
pfuze100-regulator 0-0008: pfuze3000 found.
30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 274, base_baud = 1500000) isX
console [ttymxc0] enabled
30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 275, base_baud = 5000000) isX
imx sema4 driver is registered.
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
brd: module loaded
loop: module loaded
input: fxos8700 as /devices/platform/soc/30800000.aips-bus/30a50000.i2c/i2c-3/30
fxos8700 device driver probe successfully
input: fxas2100x as /devices/platform/soc/30800000.aips-bus/30a50000.i2c/i2c-3/1
fxas2100x 3-0020: fxas2100x device driver probe successfully
CAN device driver interface
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-mxc: Freescale On-Chip EHCI Host driver
u***core: registered new interface driver u***-storage
u***core: registered new interface driver u***_ehset_test
30b10200.u***misc supply vbus-wakeup not found, using dummy regulator
30b20200.u***misc supply vbus-wakeup not found, using dummy regulator
30b30200.u***misc supply vbus-wakeup not found, using dummy regulator
mousedev: PS/2 mouse device common for all mice
input: 30370000.snvs:snvs-powerkey as /devices/platform/soc/30000000.aips-bus/32
[HXTP] Himax 852xES touch panel driver init
[HXTP] himax852xes_init_async:Enter
input: synaptics_dsx as /devices/platform/soc/30800000.aips-bus/30a30000.i2c/i23
read mpl3115 chip id 0xc4
input: mpl3115 as /devices/virtual/input/input4
mpl3115 device driver probe successfully
snvs_rtc 30370000.snvs:snvs-rtc-lp: rtc core: registered 30370000.snvs:snvs- as0
i2c /dev entries driver
IR NEC protocol handler initialized
IR RC5(x/sz) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR SANYO protocol handler initialized
IR Sharp protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
IR XMP protocol handler initialized
pxp-v4l2 pxp_v4l2_out: initialized
imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0)
Bluetooth: HCI UART driver ver 2.3
Bluetooth: HCI UART protocol H4 registered
u***core: registered new interface driver bcm203x
fwu_start_reflash: Start of reflash process
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
synaptics_dsx_i2c 1-0020: fwu_go_nogo: Device firmware ID = 1935790
/soc/aips-bus@30800000/usdhc@30b40000: voltage-ranges unspecified
sdhci-esdhc-imx 30b40000.usdhc: assigned as wifi host
synaptics_dsx_i2c 1-0020: fwu_go_nogo: Image firmware ID = 1935790
synaptics_dsx_i2c 1-0020: fwu_go_nogo: No need to do reflash
sdhci-esdhc-imx 30b40000.usdhc: No vmmc regulator found
sdhci-esdhc-imx 30b40000.usdhc: No vqmmc regulator found
mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA
/soc/aips-bus@30800000/usdhc@30b60000: voltage-ranges unspecified
sdhci-esdhc-imx 30b60000.usdhc: No vmmc regulator found
sdhci-esdhc-imx 30b60000.usdhc: No vqmmc regulator found
mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA
snvs-secvio 30370000.caam-snvs: can't get snvs clock
snvs-secvio 30370000.caam-snvs: violation handlers armed - non-secure state
u***core: registered new interface driver u***hid
u***hid: USB HID core driver
ashmem: initialized
NET: Registered protocol family 26
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
8021q: 802.1Q VLAN Support v1.8
[rfkill_bluedroid_probe] set bt_rst_gpio: 145
rfkill-bluedroid rfkill-bluedroid: bluedroid initialized
[rfkill_bluedroid_set_block] set gpio 145 value 1
Key type dns_resolver registered
cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
backlight supply power not found, using dummy regulator
sgtl5000 3-000a: sgtl5000 revision 0x11
fwu_start_reflash: End of reflash process
sgtl5000 3-000a: Using internal LDO instead of VDDD
asoc-simple-card sound: sgtl5000 <-> 308a0000.sai mapping ok
backlight supply power not found, using dummy regulator
file system registered
Mass Storage Function, version: 2009/09/11
LUN: removable file: (no medium)
Number of LUNs=1
android_u*** gadget: android_u*** ready
input: gpio-keys as /devices/platform/gpio-keys/input/input5
backlight supply power not found, using dummy regulator
snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:08:47)
mmc2: MAN_BKOPS_EN bit is not set
wlreg_on: disabling
mmc2: mmc_select_hs200 failed, error -74
: switch to mmc2 failed
mmc2: new MMC card at address 0001
ALSA device list:
#0: imx7s-sgtl5000
Warning: unable to open an initial console.
mmcblk2: mmc2:0001 EH8CD4 7.13 GiB
mmcblk2boot0: mmc2:0001 EH8CD4 partition 1 4.00 MiB
Freeing unused kernel memory: 1220K (80adb000 - 80c0c000)
mmcblk2boot1: mmc2:0001 EH8CD4 partition 2 4.00 MiB
mmcblk2rpmb: mmc2:0001 EH8CD4 partition 3 4.00 MiB
mmcblk2: p1 p2 p3
backlight supply power not found, using dummy regulator
android_work: sent uevent USB_STATE=CONNECTED
init: Failed to read from /dev/hw_random: No such device
android_work: sent uevent USB_STATE=DISCONNECTED
Console: switching to colour dummy device 80x30
init: Failed to read from /dev/hw_random: No such device
EXT4-fs (mmcblk2p2): INFO: recovery required on readonly filesystem
EXT4-fs (mmcblk2p2): write access will be enabled during recovery
EXT4-fs (mmcblk2p2): recovery complete
EXT4-fs (mmcblk2p2): mounted filesystem with ordered data mode. Opts: barrier=1
fs_mgr: __mount(source=/dev/block/mmcblk2p2,target=/system,type=ext4)=0
EXT4-fs (mmcblk2p3): Ignoring removed nomblk_io_submit option
EXT4-fs (mmcblk2p3): recovery complete
EXT4-fs (mmcblk2p3): mounted filesystem with ordered data mode. Opts: nomblk_ioc
fs_mgr: __mount(source=/dev/block/mmcblk2p3,target=/data,type=ext4)=0
backlight supply power not found, using dummy regulator
android_work: sent uevent USB_STATE=CONNECTED
ci_hdrc ci_hdrc.0: freeing queued request
android_work: sent uevent USB_STATE=DISCONNECTED
mxc_mipi-csi 30750000.mipi-csi: mipi csi v4l2 device registered
CSI: Registered sensor subdevice: mxc_mipi-csi.0
mxc_mipi-csi 30750000.mipi-csi: lanes: 1, hs_settle: 3, clk_settle: 0, wclk: 1,0
backlight supply power not found, using dummy regulator
[rfkill_bluedroid_set_block] set gpio 145 value 0
random: init urandom read with 21 bits of entropy available
android_work: sent uevent USB_STATE=CONNECTED
android_work: sent uevent USB_STATE=DISCONNECTED
binder: 96:96 transaction failed 29189, size 0-0
init: using deprecated syntax for specifying property 'ro.serialno', use ${named
init: property 'ro.serialno' doesn't exist while expanding '$ro.serialno'
init: cannot expand '$ro.serialno' while writing to '/sys/class/android_u***/and'
init: using deprecated syntax for specifying property 'ro.product.manufacturer'd
init: using deprecated syntax for specifying property 'ro.product.model', use $d
init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
android_work: sent uevent USB_STATE=CONNECTED
android_work: sent uevent USB_STATE=DISCONNECTED
init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
init: cannot find '/system/bin/fsl_sensor_fusion', disabling 'sensor_fusion'
android_u***: already disabled
read descriptors
read strings
mtp_bind_config
android_work: sent uevent USB_STATE=CONNECTED
android_u*** gadget: high-speed config #1: android
android_work: sent uevent USB_STATE=CONFIGURED
logd.auditd: start
root@warp7:/ # healthd: No charger supplies found
healthd: No battery devices found
capability: warning: `main' uses 32-bit capabilities (legacy support in use)
misc FreescaleGyroscope: mma enable setting active
misc FreescaleGyroscope: mma enable setting active
misc FreescaleGyroscope: mma enable setting active
random: nonblocking pool is initialized
acc_open
acc_release
dhd_module_init in
Power-up adapter 'DHD generic adapter'
wifi_platform_bus_enumerate device present 1
mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
mmc0: queuing unknown CIS tuple 0x80 (6 bytes)
mmc0: new high speed SDIO card at address 0001
backlight supply power not found, using dummy regulator
backlight supply power not found, using dummy regulator
F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x1 pkg:0x3
backlight supply power not found, using dummy regulator
DHD: dongle ram size is set to 524288(orig 524288) at 0x0
wifi_platform_get_mac_addr
CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211)
wl_create_event_handler(): thread:wl_event_handler:263 started
CFG80211-ERROR) wl_event_handler : tsk Enter, tsk = 0x88a0143c
dhd_attach(): thread:dhd_watchdog_thread:264 started
dhd_attach(): thread:dhd_dpc:265 started
dhd_deferred_work_init: work queue initialized
dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
wifi_platform_get_mac_addr
Firmware up: op_mode=0x0005, MAC=60:f1:89:40:51:c3
Firmware version = wl0: Dec 29 2015 15:56:15 version 7.45.41.24 (r608913) FWID 5
dhd_wlfc_init(): successfully enabled bdcv2 tlv signaling, 79
dhd_wlfc_init: query wlfc_mode succeed, fw_caps=0x1c
dhd_wlfc_init(): wlfc_mode=0x1c, ret=0
Dongle Host Driver, version 1.141.88 (r)
Compiled from
Register interface [wlan0] MAC: 60:f1:89:40:51:c3
backlight supply power not found, using dummy regulator
backlight supply power not found, using dummy regulator
CFG80211-ERROR) wl_update_wiphybands : error reading vhtmode (-23)
CFGP2P-ERROR) wl_cfgp2p_add_p2p_disc_if : P2P interface registered
WLC_E_IF: NO_IF set, event Ignored
CFG80211-ERROR) wl_update_wiphybands : error reading vhtmode (-23)
dhd_set_suspend: Remove extra suspend setting
mtp_open
misc FreescaleGyroscope: mma enable setting active
[rfkill_bluedroid_set_block] set gpio 145 value 0
[rfkill_bluedroid_set_block] set gpio 145 value 1
mpl3115 set active
mpl3115 set inactive
完整启动log |
5887
/6 
工商网监
湘ICP备2023018690号
淘帖
赞
回复
显身卡
