想用BananaPi做个NAS,因为之前有玩过OPENWRT,想着系统最小用张小点的内存卡在挂个硬盘妥妥的。还可以当下载机,于是下载下来刷内存卡,启动起来没现象,网口灯闪两下就灭了一直重复。用TL线打印开机信息如下
- U-Boot SPL 2015.01 (Aug 25 2015 - 10:42:17)
- DRAM: 1024 MiB
- CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
- U-Boot 2015.01 (Aug 25 2015 - 10:42:17) Allwinner Technology
- CPU: Allwinner A20 (SUN7I)
- I2C: ready
- DRAM: 1016 MiB
- MMC: SUNXI SD/MMC: 0
- *** Warning - bad CRC, using default environment
- Reserved 8192kB of RAM for Framebuffer.
- In: serial
- Out: serial
- Err: serial
- SCSI: SUNXI SCSI INIT
- SATA link 0 timeout.
- AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
- flags: ncq stag pm led clo only pmp pio slum part ccc apst
- Net: dwmac.1c50000
- (Re)start USB...
- USB0: USB EHCI 1.00
- scanning bus 0 for devices... 1 USB Device(s) found
- USB1: USB EHCI 1.00
- scanning bus 1 for devices... 2 USB Device(s) found
- scanning u*** for storage devices... 0 Storage Device(s) found
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- Scanning mmc 0...
- Found U-Boot script /boot.scr
- reading /boot.scr
- 377 bytes read in 16 ms (22.5 KiB/s)
- ## Executing script at 43100000
- reading uImage
- 1924456 bytes read in 112 ms (16.4 MiB/s)
- reading dtb
- 24215 bytes read in 27 ms (875 KiB/s)
- ## Booting kernel from Legacy Image at 42000000 ...
- Image Name: ARM OpenWrt Linux-3.18.19
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 1924392 Bytes = 1.8 MiB
- Load Address: 40008000
- Entry Point: 40008000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 43000000
- Booting using the fdt blob at 0x43000000
- Loading Kernel Image ... OK
- Using Device Tree in place at 43000000, end 43008e96
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Linux version 3.18.19 (charli@charli-pc) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #7 SMP PREEMPT Tue Aug 25 12:13:18 CST 2015
- [ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine model: BPI M1 Plus
- [ 0.000000] Memory policy: Data cache writealloc
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
- [ 0.000000] PERCPU: Embedded 9 pages/cpu @eefe0000 s6272 r8192 d22400 u36864
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 258576
- [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2
- [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
- [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Memory: 1025364K/1040384K available (3827K kernel code, 169K rwdata, 1068K rodata, 200K init, 606K bss, 15020K reserved, 262144K highmem)
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
- [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
- [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000] .text : 0xc0008000 - 0xc04cfef4 (4896 kB)
- [ 0.000000] .init : 0xc04d0000 - 0xc0502000 ( 200 kB)
- [ 0.000000] .data : 0xc0502000 - 0xc052c778 ( 170 kB)
- [ 0.000000] .bss : 0xc052c778 - 0xc05c4088 ( 607 kB)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Preemptible hierarchical RCU implementation.
- [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
- [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
- [ 0.000000] NR_IRQS:16 nr_irqs:16 16
- [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
- [ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
- [ 0.000021] Switching to timer-based delay loop, resolution 41ns
- [ 0.000360] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
- [ 0.000516] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 26843545593ns
- [ 0.000681] Console: colour dummy device 80x30
- [ 0.000709] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
- [ 0.000725] pid_max: default: 32768 minimum: 301
- [ 0.000829] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000841] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.001456] CPU: Testing write buffer coherency: ok
- [ 0.001757] /cpus/cpu@0 missing clock-frequency property
- [ 0.001776] /cpus/cpu@1 missing clock-frequency property
- [ 0.001790] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- [ 0.001844] Setting up static identity map for 0x40011b68 - 0x40011b9c
- [ 0.060434] CPU1: Booted secondary processor
- [ 0.060475] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
- [ 0.060545] Brought up 2 CPUs
- [ 0.060568] SMP: Total of 2 processors activated (96.00 BogoMIPS).
- [ 0.060575] CPU: All CPU(s) started in HYP mode.
- [ 0.060580] CPU: Virtualization extensions available.
- [ 0.064960] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
- [ 0.065360] pinctrl core: initialized pinctrl subsystem
- [ 0.065755] regulator-dummy: no parameters
- [ 0.072026] NET: Registered protocol family 16
- [ 0.072379] DMA: preallocated 256 KiB pool for atomic coherent allocations
- [ 0.111466] reg-fixed-voltage u***1-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/u***1_vbus_pin@0, deferring probe
- [ 0.111501] platform u***1-vbus: Driver reg-fixed-voltage requests probe deferral
- [ 0.111533] reg-fixed-voltage u***2-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/u***2_vbus_pin@0, deferring probe
- [ 0.111549] platform u***2-vbus: Driver reg-fixed-voltage requests probe deferral
- [ 0.111742] vcc3v0: 3000 mV
- [ 0.111960] vcc3v3: 3300 mV
- [ 0.112202] vcc5v0: 5000 mV
- [ 0.112290] reg-fixed-voltage gmac-3v3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/gmac_power_pin@0, deferring probe
- [ 0.112308] platform gmac-3v3: Driver reg-fixed-voltage requests probe deferral
- [ 0.112333] reg-fixed-voltage vmmc3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/vmmc3_pin@0, deferring probe
- [ 0.112348] platform vmmc3: Driver reg-fixed-voltage requests probe deferral
- [ 0.112797] SCSI subsystem initialized
- [ 0.113196] u***core: registered new interface driver u***fs
- [ 0.113275] u***core: registered new interface driver hub
- [ 0.113392] u***core: registered new device driver u***
- [ 0.113537] pps_core: LinuxPPS API ver. 1 registered
- [ 0.113544] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
- [ 0.113577] PTP clock support registered
- [ 0.114651] Switched to clocksource arch_sys_counter
- [ 0.121740] NET: Registered protocol family 2
- [ 0.122789] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.122873] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
- [ 0.122994] TCP: Hash tables configured (established 8192 bind 8192)
- [ 0.123075] TCP: reno registered
- [ 0.123090] UDP hash table entries: 512 (order: 2, 16384 bytes)
- [ 0.123147] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- [ 0.123419] NET: Registered protocol family 1
- [ 0.124923] futex hash table entries: 512 (order: 3, 32768 bytes)
- [ 0.125081] audit: initializing netlink subsys (disabled)
- [ 0.125167] audit: type=2000 audit(0.110:1): initialized
- [ 0.133977] VFS: Disk quotas dquot_6.5.2
- [ 0.134244] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 0.135982] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.136000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.136718] msgmni has been set to 1490
- [ 0.138883] bounce: pool size: 64 pages
- [ 0.138909] io scheduler noop registered
- [ 0.138923] io scheduler deadline registered
- [ 0.138972] io scheduler cfq registered (default)
- [ 0.139295] platform 1c13400.phy: Driver sun4i-u***-phy requests probe deferral
- [ 0.141988] sun7i-a20-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
- [ 0.184633] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
- [ 0.187173] console [ttyS0] disabled
- [ 0.207587] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A
- [ 0.828016] console [ttyS0] enabled
- [ 0.854569] 1c28800.serial: ttyS1 at MMIO 0x1c28800 (irq = 35, base_baud = 1500000) is a U6_16550A
- [ 0.886509] 1c29c00.serial: ttyS2 at MMIO 0x1c29c00 (irq = 52, base_baud = 1500000) is a U6_16550A
- [ 0.899009] platform 1c50000.ethernet: Driver stmmaceth requests probe deferral
- [ 0.906482] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 0.913010] ehci-platform: EHCI generic platform driver
- [ 0.918409] platform 1c14000.u***: Driver ehci-platform requests probe deferral
- [ 0.925729] platform 1c1c000.u***: Driver ehci-platform requests probe deferral
- [ 0.933047] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 0.939277] ohci-platform: OHCI generic platform driver
- [ 0.944624] platform 1c14400.u***: Driver ohci-platform requests probe deferral
- [ 0.951939] platform 1c1c400.u***: Driver ohci-platform requests probe deferral
- [ 0.959340] u***core: registered new interface driver u***-storage
- [ 0.965629] mousedev: PS/2 mouse device common for all mice
- [ 0.975985] axp20x-regulator axp20x-regulator: regulators node not found
- [ 0.982808] LDO1: 1300 mV
- [ 0.985991] LDO2: at 3000 mV
- [ 0.989376] LDO3: at 2275 mV
- [ 0.992510] LDO4: at 2800 mV
- [ 0.995911] LDO5: at 2800 mV
- [ 0.999301] DCDC2: at 1400 mV
- [ 1.002752] DCDC3: at 1250 mV
- [ 1.005932] axp20x 0-0034: AXP20X driver loaded
- [ 1.011478] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
- [ 1.020058] sunxi-mmc 1c0f000.mmc: No vqmmc regulator found
- [ 1.025985] sunxi-mmc 1c0f000.mmc: Got CD GPIO
- [ 1.064922] sunxi-mmc 1c0f000.mmc: base:0xf00f6000 irq:64
- [ 1.070801] platform 1c12000.mmc: Driver sunxi-mmc requests probe deferral
- [ 1.080141] sunxi-ss 1c15000.crypto-engine: Die ID 0
- [ 1.087209] TCP: cubic registered
- [ 1.090538] Initializing XFRM netlink socket
- [ 1.094913] NET: Registered protocol family 17
- [ 1.099478] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.112097] 8021q: 802.1Q VLAN Support v1.8
- [ 1.116426] Registering SWP/SWPB emulation handler
- [ 1.121730] registered taskstats version 1
- [ 1.126483] u***1-vbus: 5000 mV
- [ 1.130018] u***2-vbus: 5000 mV
- [ 1.133511] gmac-3v3: 3300 mV
- [ 1.137043] vmmc3: 3300 mV
- [ 1.203035] mmc0: host does not support reading read-only switch, assuming write-enable
- [ 1.213645] mmc0: new high speed SDHC card at address ab27
- [ 1.219647] mmcblk0: mmc0:ab27 SD04G 3.69 GiB
- [ 1.225476] mmcblk0: p1 p2
- [ 1.244738] stmmaceth 1c50000.ethernet: no reset control found
- [ 1.250573] Ring mode enabled
- [ 1.253626] No HW DMA feature register supported
- [ 1.258169] Normal descriptors
- [ 1.261489] TX Checksum insertion supported
- [ 1.270023] libphy: stmmac: probed
- [ 1.273434] eth0: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
- [ 1.279841] eth0: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
- [ 1.285956] ehci-platform 1c14000.u***: EHCI Host Controller
- [ 1.291559] ehci-platform 1c14000.u***: new USB bus registered, assigned bus number 1
- [ 1.299453] ehci-platform 1c14000.u***: irq 71, io mem 0x01c14000
- [ 1.324671] ehci-platform 1c14000.u***: USB 2.0 started, EHCI 1.00
- [ 1.330968] u*** u***1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 1.337774] u*** u***1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.344998] u*** u***1: Product: EHCI Host Controller
- [ 1.349872] u*** u***1: Manufacturer: Linux 3.18.19 ehci_hcd
- [ 1.355363] u*** u***1: SerialNumber: 1c14000.u***
- [ 1.360460] hub 1-0:1.0: USB hub found
- [ 1.364248] hub 1-0:1.0: 1 port detected
- [ 1.368952] ehci-platform 1c1c000.u***: EHCI Host Controller
- [ 1.374554] ehci-platform 1c1c000.u***: new USB bus registered, assigned bus number 2
- [ 1.382448] ehci-platform 1c1c000.u***: irq 72, io mem 0x01c1c000
- [ 1.404673] ehci-platform 1c1c000.u***: USB 2.0 started, EHCI 1.00
- [ 1.410947] u*** u***2: New USB device found, idVendor=1d6b, idProduct=0002
- [ 1.417750] u*** u***2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.424975] u*** u***2: Product: EHCI Host Controller
- [ 1.429849] u*** u***2: Manufacturer: Linux 3.18.19 ehci_hcd
- [ 1.435340] u*** u***2: SerialNumber: 1c1c000.u***
- [ 1.440435] hub 2-0:1.0: USB hub found
- [ 1.444220] hub 2-0:1.0: 1 port detected
- [ 1.448813] ohci-platform 1c14400.u***: Generic Platform OHCI controller
- [ 1.455498] ohci-platform 1c14400.u***: new USB bus registered, assigned bus number 3
- [ 1.463368] ohci-platform 1c14400.u***: irq 96, io mem 0x01c14400
- [ 1.528841] u*** u***3: New USB device found, idVendor=1d6b, idProduct=0001
- [ 1.535651] u*** u***3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.542865] u*** u***3: Product: Generic Platform OHCI controller
- [ 1.548797] u*** u***3: Manufacturer: Linux 3.18.19 ohci_hcd
- [ 1.554277] u*** u***3: SerialNumber: 1c14400.u***
- [ 1.559389] hub 3-0:1.0: USB hub found
- [ 1.563173] hub 3-0:1.0: 1 port detected
- [ 1.567727] ohci-platform 1c1c400.u***: Generic Platform OHCI controller
- [ 1.574365] ohci-platform 1c1c400.u***: new USB bus registered, assigned bus number 4
- [ 1.582249] ohci-platform 1c1c400.u***: irq 97, io mem 0x01c1c400
- [ 1.648855] u*** u***4: New USB device found, idVendor=1d6b, idProduct=0001
- [ 1.655657] u*** u***4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.662871] u*** u***4: Product: Generic Platform OHCI controller
- [ 1.668804] u*** u***4: Manufacturer: Linux 3.18.19 ohci_hcd
- [ 1.674285] u*** u***4: SerialNumber: 1c1c400.u***
- [ 1.679354] hub 4-0:1.0: USB hub found
- [ 1.683151] hub 4-0:1.0: 1 port detected
- [ 1.688022] sunxi-mmc 1c12000.mmc: No vqmmc regulator found
- [ 1.764674] u*** 2-1: new high-speed USB device number 2 using ehci-platform
- [ 1.915506] u*** 2-1: New USB device found, idVendor=0bda, idProduct=8179
- [ 1.922213] u*** 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [ 1.929356] u*** 2-1: Product: 802.11n NIC
- [ 1.933368] u*** 2-1: Manufacturer: Realtek
- [ 1.937474] u*** 2-1: SerialNumber: 00E04C0001
- [ 1.954647] sunxi-mmc 1c12000.mmc: fatal err update clk timeout
- [ 1.974676] sunxi-mmc 1c12000.mmc: base:0xf0140000 irq:67
- [ 1.984935] vcc5v0: disabling
- [ 1.987940] vcc3v0: disabling
- [ 1.993008] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
- [ 2.001806] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
- [ 2.014026] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
- [ 2.021634] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
- [ 2.028708] Freeing unused kernel memory: 200K (c04d0000 - c0502000)
- [ 2.149981] init: Console is alive
- [ 2.153678] init: - watchdog -
- [ 2.224679] sunxi-mmc 1c12000.mmc: fatal err update clk timeout
- [ 2.474652] sunxi-mmc 1c12000.mmc: fatal err update clk timeout
- [ 2.484707] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
- [ 2.492189] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
- [ 2.498087] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
- [ 2.507057] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
- [ 2.516055] scsi host0: ahci_platform
- [ 2.520097] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88
- [ 2.724643] sunxi-mmc 1c12000.mmc: fatal err update clk timeout
- [ 2.874663] ata1: SATA link down (SStatus 0 SControl 300)
- [ 3.157738] init: - preinit -
- Detected bpi-m1-plus // BPI M1 Plus
- [ 3.224937] random: mktemp urandom read with 7 bits of entropy available
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 6.287659] mount_root: mounting /dev/root
- [ 6.292512] EXT4-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
- [ 6.316993] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
- [ 6.322675] mount_root: loading kmods from internal overlay
- [ 6.377990] block: attempting to load /etc/config/fstab
- [ 6.385789] block: extroot: not configured
- [ 6.395586] procd: - early -
- [ 6.398603] procd: - watchdog -
- Failed to connect to ubus
- [ 7.130388] procd: - ubus -
- [ 8.134699] procd: - init -
- Please press Enter to activate this console.
- [ 9.576594] NET: Registered protocol family 10
- [ 9.601736] ntfs: driver 2.1.31 [Flags: R/O MODULE].
- [ 9.640898] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 9.655274] Netfilter messages via NETLINK v0.30.
- [ 9.662569] ip_set: protocol 6
- [ 9.701512] u32 classifier
- [ 9.704242] input device check on
- [ 9.708087] Actions configured
- [ 9.712901] Mirror/redirect action on
- [ 9.722316] nf_conntrack version 0.5.0 (16024 buckets, 64096 max)
- [ 9.733732] fuse init (API version 7.23)
- [ 9.774315] Loading modules backported from Linux version master-2015-03-09-0-g141f155
- [ 9.782476] Backport generated by backports.git backports-20150129-0-gdd4a670
- [ 9.793335] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 9.803180] lib80211: common routines for IEEE802.11 drivers
- [ 9.890343] u***core: registered new interface driver u***lp
- [ 9.920550] xt_time: kernel timezone is -0000
- [ 9.938077] cfg80211: Calling CRDA to update world regulatory domain
- [ 9.945507] cfg80211: World regulatory domain updated:
- [ 9.950797] cfg80211: DFS Master region: unset
- [ 9.955207] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- [ 9.965719] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 9.974389] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 9.983141] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- [ 9.991867] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- [ 10.000625] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
- [ 10.010842] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
- [ 10.019681] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- [ 10.028386] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- [ 10.069436] mac80211_hwsim: initializing netlink
- [ 10.092638] u***core: registered new interface driver p54u***
- [ 10.101422] PPP generic driver version 2.4.2
- [ 10.108502] NET: Registered protocol family 24
- [ 10.121785] u***core: registered new interface driver rt73u***
- [ 10.130867] u***core: registered new interface driver rtl8187
- [ 10.143786] u***core: registered new interface driver u***8xxx
- [ 10.158667] u***core: registered new interface driver brcmfmac
- [ 10.168080] u***core: registered new interface driver carl9170
- [ 10.179972] u***core: registered new interface driver rt2500u***
- [ 10.191634] u***core: registered new interface driver rt2800u***
- [ 10.205431] u***core: registered new interface driver rtl8192cu
- [ 13.125525] RX IPC Checksum Offload disabled
- [ 13.129927] No MAC Management Counters available
- [ 18.114997] stmmaceth 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
- BusyBox v1.23.2 (2015-08-25 10:40:44 CST) built-in shell (ash)
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- CHAOS CALMER (Chaos Calmer, unknown)
- Edited by Datou for BPI
- BPI Web: http://www.bananapi.com
- Datou's Blog: http://www.lichanglin.cn
- -----------------------------------------------------
- * 1 1/2 oz Gin Shake with a glassful
- * 1/4 oz Triple Sec of broken ice and pour
- * 3/4 oz Lime Juice unstrained into a goblet.
- * 1 1/2 oz Orange Juice
- * 1 tsp. Grenadine Syrup
- -----------------------------------------------------
- root@BananaPi:/#
复制代码
不知道有没有朋友遇到过。
0
|
|
|
|