单片2051+SD卡和3310做的音乐播放器

ti

转自网络：
这个小玩意，采用 ATMEL 的传统51MCU作主控制芯片，加上SD卡和显示屏，就可以作简单的音乐播放器了，虽然音质不怎么样，不过作为DIY还是蛮有乐趣，希望大家喜欢。
没有采用FAT文件系统，只是按扇区读取SD卡，由于2051资源有限，改为4051有望可以操作FAT，但目前程序还在不断完善中。
128byte怎样读取512byte的扇区数据？可以采用边读边播放的方式，就能解决。音乐文件是32KHz取样率的WAV文件，所以和HIFI就沾不上边了。

#include
#include
#include
#include "LCD_3310.H"
#define uchar unsigned char
#define uint unsigned int
#define ulong unsigned long
/************ 定义管脚 *************/
***it DOUT = P3^0; //SD卡数据输出
***it CLK = P3^1; //SD卡时钟输入
***it DIN = P3^2; //SD卡数据输入
***it CS = P3^3; //SD卡片选使能
/************ 全局变量 ************/
uchar pbuf[64]; //数据缓冲区
uchar p; //播放缓冲区指针
uchar px; //频谱显示的X坐标
code ulong Track[17] =
{ //0x15000,0x58000 SD卡中各声音文件的首址，以后打算把这些数据放在SD卡的特定配置文件中再读入。
0xd7800-0x8a00,0x76b800-0x8a00,0xedc000-0x8a00,0x1752800-0x8a00,0x1F08000-0x8a00,
0x2569800-0x8a00,0x2EDB800-0x8a00,0x3480000-0x8a00,0x3BFA800-0x8a00,
0x41EB000-0x8a00,0x48EF000-0x8a00,0x508A000-0x8a00,0x59AE800-0x8a00,
0x60AF000-0x8a00,0x6878000-0x8a00,0x6DBE000-0x8a00,0x7525800-0x8a00,
};
/******* SD访问错误码的定义 *******/
#define INIT_CMD0_ERROR 0X01
#define INIT_CMD1_ERROR 0X02
#define READ_BLOCK_ERROR 0X03
#define WRITE_BLOCK_ERROR 0X04
/********* 通用延时函数 ***********/
void delay(uint i)
{
while(i--);
}
/******** SD写入一个字节 **********/
void spi_write(uchar x)
{ //不采用循环结构是为了提高处理速度
DIN = x & 0x80;
CLK = 0;
CLK = 1;
DIN = x & 0x40;
CLK = 0;
CLK = 1;
DIN = x & 0x20;
CLK = 0;
CLK = 1;
DIN = x & 0x10;
CLK = 0;
CLK = 1;
DIN = x & 0x08;
CLK = 0;
CLK = 1;
DIN = x & 0x04;
CLK = 0;
CLK = 1;
DIN = x & 0x02;
CLK = 0;
CLK = 1;
DIN = x & 0x01;
CLK = 0;
CLK = 1;
}
/******* SD慢速写入一个字节 ********/
void spi_write_low_speed(uchar x)
{
uchar i;
for(i = 8; i; --i)
{
DIN = x & 0x80;
x <<= 1;
CLK = 0;
delay(1);
CLK = 1;
delay(1);
}
}
/*********** SD读入一字节 ***********/
uchar spi_read(void)
{ //利用51串口的同步移位功能，以达了最高的读度2MHz CLK
RI = 0;
while(RI == 0);
return SBUF;
}
/******** SD慢速读入一字节 **********/
uchar spi_read_low_speed(void)
{
uchar temp,i;
for(i = 8; i; --i)
{
CLK = 0;
delay(1);
temp <<= 1;
if(DOUT) temp++;
CLK = 1;
delay(1);
}
return temp;
}
/******** 发送一组SD命令 ************/
uchar write_cmd(uchar data *pcmd)
{
uchar temp,time=0,i;
for(i = 0; i<6; i++) //一条命令都是6个字节，形参用指针，
{ //指向6个字节命令，
spi_write(pcmd);
}
do //看看写进去没有,通过so管脚
{
temp = spi_read();
time++;
} //一直到读到的不是0xff或超时，退出去
while(temp==0xff && time<100);
return temp;
}
/****** 慢速发送一组SD命令 **********/
uchar write_cmd_low_speed(uchar *pcmd)
{
uchar temp,time=0,i;
for(i=0;i<6;i++) //一条命令都是6个字节，形参用指针，
{ //指向6个字节命令，
spi_write_low_speed(pcmd);
}
do //看看写进去没有,通过so管脚
{
temp = spi_read_low_speed();
time++;
} //一直到读到的不是0xff或超时，退出去
while(temp==0xff && time<100);
return temp;
}
/********* SD卡激活，复位 *********/
uchar sd_reset(void)
{
uchar time,temp,i;
uchar pcmd[6]={0x40,0x00,0x00,0x00,0x00,0x95};
CS = 1;
for(i = 0; i < 0x0f; i++) //复位时，至少要72个时钟周期，
{ //现在是，15*8=120个clk
spi_write_low_speed(0xff);
}
CS = 0;
time=0;
do
{
temp = write_cmd_low_speed(pcmd);
time++;
if(time > 100) return INIT_CMD0_ERROR;
}
while(temp != 0x01); //校验码是0x01，表示写入成功
CS = 1;
spi_write_low_speed(0xff);//时序上要求补8个clk
return 0; //返回0，写入成功
}
/************ SD卡初始化 ************/
uchar sd_init(void)
{
uchar time, temp;
uchar pcmd[6] = {0x41,0x00,0x00,0x00,0x00,0xff};
CS = 0;
time = 0;
do
{
temp = write_cmd_low_speed(pcmd);
time++;
if(time > 100) return INIT_CMD1_ERROR;
}
while(temp != 0x00);
CS = 1;
spi_write_low_speed(0xff);
return 0;
}
/******* 读取一扇区的点阵图像 *********/
uchar sd_read_bmp(uchar data *ad)
{
uchar temp, time, x, pcmd[6];
uint j = 0;
pcmd[0] = 0x51;
pcmd[1] = *ad;
pcmd[2] = *(++ad);
pcmd[3] = *(++ad);
pcmd[4] = 0;
pcmd[5] = 0xff;
CS = 0;
time = 0;
do
{
temp = write_cmd(pcmd);
if(++time > 100)
{
CS = 1;
return READ_BLOCK_ERROR;
}
}
while(temp != 0);
//等待SD卡回应
while(spi_read() != 0x7f); //0xfe,51的串口移位是LSB优先，所以结果高低位倒置
for (j = 0; j < 504; j++) //3310的分辨率为 84 * 48,总计用504字节
{
LCD3310_write_dat(spi_read());
}
for (x = 0; x < 10; x++) spi_read(); //略过8字节数据和2字节CRC
spi_write(0xff);
CS = 1;
return 0;
}
/******* 读取一扇区的声音数据 *********/
uchar sd_read_sector(uchar data *ad)
{
uchar temp, time, pcmd[6];
uint j = 0;
pcmd[0] = 0x51;
pcmd[1] = *ad;
pcmd[2] = *(++ad);
pcmd[3] = *(++ad);
pcmd[4] = 0;
pcmd[5] = 0xff;
CS = 0;
time = 0;
do
{
temp = write_cmd(pcmd);
if(++time > 100)
{
CS = 1;
return READ_BLOCK_ERROR;
}
}
while(temp != 0);
//等待SD回应的时间有点长，所以在这里插入显示模拟的频谱图
temp = pbuf[16]; //随便挑一个数据显示
LCD3310_set_XY(px,5); //设定显示位置
px += 6;
if (px >= 39) px = 0;
if (temp & 0x80) temp ^= 0x80; //求得声音振幅
else temp = 0x80 - temp;
temp = Level[temp>>4]; //不同幅度对应不同的谱线图案
LCD3310_write_dat(temp);
LCD3310_write_dat(temp);
LCD3310_write_dat(temp);
while(spi_read() != 0x7f);//0xfe,51的串口移位是LSB优先，所以结果高低位倒置
while(1) //读取512字节数据
{
RI = 0;_nop_(); pbuf[j++ & 63] = SBUF; //为求快速，不用函数调用
RI = 0;_nop_(); pbuf[j++ & 63] = SBUF; //直接启动串口移入
RI = 0;_nop_(); pbuf[j++ & 63] = SBUF; //连续读四字节
RI = 0;_nop_(); pbuf[j++ & 63] = SBUF;
if(j >= 512) break;
while((((uchar)j - p) & 63) > 55); //检测播放进度，
} //如果缓冲区接近溢出，先暂停等待
spi_read();//略过 crc
spi_read();//略过 crc
spi_write(0xff);//SD 时序要求补8个脉冲
CS = 1;
return 0;
}
/**************************** 主程序 *******************************/
int main(void)
{
uchar key,n,Count,Min,Sec;
ulong addr; // SD 的扇区地址
P1 = 0x80; // DAC 输出中点电压
RI = 1;
REN = 1;
TMOD = 0x02;
TH0 = 256 - 62.5; //定时器设定约为 32KHz，和WAV文件取样率对应
ET0 = 1;
EA = 1;
px = 0;
n = 64;
do pbuf[--n] = 0x80; while(n); //填充播放缓冲区
delay(65535);
LCD3310_init();
LCD3310_set_XY(0,0);
LCD3310_write_cmd(0x22); //设定LCD扫描顺序
sd_reset();
sd_init();
addr = 0x4f400;
sd_read_bmp((uchar) &addr); //显示欢迎画面
while (D_C == 1) ;
while (D_C == 0) ; //等待按键
delay(65535);
//============== main loop ==================
while(1) //循环播放所有曲目
{
TR0 = 0;
LCD3310_write_cmd(0x22);
LCD3310_set_XY(0,0);
addr = 0x4f600 + ((uint)n<<9);
sd_read_bmp((uchar) &addr); //显示歌名、歌手
LCD3310_write_cmd(0x20);
TR0 = 1;
p = 0xd0;
Min = 0;
Sec = 0;
Count= 0;
for (addr = Track[n]; addr < Track[n+1];)//播放第n曲
{
//============ 按键处理 ===============
key = (key >> 2) | (P3 & 0x30); //仅一句的扫键函数，包括扫描和消抖
if (key == 0x03) //键码为03是播放/暂停键
{
LCD3310_set_XY(78,5);
TCON ^= 0x10; //TR0 取反
if (TR0) LCD3310_print(11); //显示播放符号
else LCD3310_print(12); //显示暂停符号
}
else if (key == 0x2b) //键码为2b是前一曲
{
if ((Min || (Sec & 0xf0))) n--;//10秒后跳本曲开始
else n -= 2; //10秒内跳前一曲
break;
}
else if (key == 0x17) //键码为17是后一曲
break;
//======== 读一扇区数据或暂停 =========
if (TR0 == 0) {delay(2000); continue;}
sd_read_sector((uchar) &addr);
addr += 512;
//=========== 播放时间计数 ============
Count += 2;
if (Count >= 125)
{
Count -= 125;
Sec++;
if ((Sec & 0x0f) > 9)
{
Sec += 6;
if (Sec >= 0x60)
{
Sec = 0;
Min++;
if ((Min & 0x0f) > 9)
{
Min += 6;
if (Min > 0x60) Min = 0;
}
}
}
}
//======= 分时间片显示时间/标志 ========
switch (Count & 14)
{
case 2:
LCD3310_set_XY(44,5);
LCD3310_print(Min>>4);//分钟十位
break;
case 4:
LCD3310_set_XY(50,5);
LCD3310_print(Min&15);//分钟个位
break;
case 6:
LCD3310_set_XY(56,5);
LCD3310_print(10); //分隔符
break;
case 8:
LCD3310_set_XY(62,5);
LCD3310_print(Sec>>4);//秒十位
break;
case 10:
LCD3310_set_XY(68,5);
LCD3310_print(Sec&15);//秒个位
break;
case 12:
LCD3310_set_XY(78,5);
if (Count & 0x40) LCD3310_print(13); //闪动播放符号
else LCD3310_print(11);
}
}
n++; //下一曲
n &= 15; //这个SD卡只有16首歌
}//while(1);
}//main()
void timer0 (void) interrupt 1 using 1
{
if (TL0 & 1) _nop_(); //消除中断响应时间不一致，造成的频率抖动
P1 = pbuf[++p & 63]; //输出一个声音数据
}

复制代码

#include
#include
***it SDIN = P3^2; //P3^2
***it SCLK = P3^4;
***it D_C = P3^5;
***it SCE = P3^7;
code unsigned char Font[70] =
{
0x3E, 0x51, 0x49, 0x45, 0x3E , // 0
0x00, 0x42, 0x7F, 0x40, 0x00 , // 1
0x42, 0x61, 0x51, 0x49, 0x46 , // 2
0x21, 0x41, 0x45, 0x4B, 0x31 , // 3
0x18, 0x14, 0x12, 0x7F, 0x10 , // 4
0x27, 0x45, 0x45, 0x45, 0x39 , // 5
0x3C, 0x4A, 0x49, 0x49, 0x30 , // 6
0x01, 0x71, 0x09, 0x05, 0x03 , // 7
0x36, 0x49, 0x49, 0x49, 0x36 , // 8
0x06, 0x49, 0x49, 0x29, 0x1E , // 9
0x00, 0x00, 0x36, 0x36, 0x00 , // :
0x7f, 0x3e, 0x1c, 0x08, 0x00 , // >
0x3e, 0x3e, 0x00, 0x3e, 0x3e , // ||
0x00, 0x00, 0x00, 0x00, 0x00 , //" "
};
code unsigned char Level[8] = {0x80,0xc0,0xe0,0xf0,0xf8,0xfc,0xfe,0xff,};
extern void delay(unsigned int i);
void LCD3310_write_cmd(unsigned char cmd)
{
D_C = 0;
SCLK = 0;
SCE = 0;
delay(3);
SDIN = cmd & 0x80;
SCLK = 1;
SDIN = cmd & 0x40;
SCLK = 0;
SCLK = 1;
SDIN = cmd & 0x20;
SCLK = 0;
SCLK = 1;
SDIN = cmd & 0x10;
SCLK = 0;
SCLK = 1;
SDIN = cmd & 0x08;
SCLK = 0;
SCLK = 1;
SDIN = cmd & 0x04;
SCLK = 0;
SCLK = 1;
SDIN = cmd & 0x02;
SCLK = 0;
SCLK = 1;
SDIN = cmd & 0x01;
SCLK = 0;
SCLK = 1;
D_C = 1;
SDIN = 1;
SCE = 1;
}
void LCD3310_write_dat(unsigned char dat)
{
// D_C = 1;
SCLK = 0;
SCE = 0;
delay(3);
SDIN = dat & 0x80;
SCLK = 1;
SDIN = dat & 0x40;
SCLK = 0;
SCLK = 1;
SDIN = dat & 0x20;
SCLK = 0;
SCLK = 1;
SDIN = dat & 0x10;
SCLK = 0;
SCLK = 1;
SDIN = dat & 0x08;
SCLK = 0;
SCLK = 1;
SDIN = dat & 0x04;
SCLK = 0;
SCLK = 1;
SDIN = dat & 0x02;
SCLK = 0;
SCLK = 1;
SDIN = dat & 0x01;
SCLK = 0;
SCLK = 1;
D_C = 1;
SDIN = 1;
SCE = 1;
}
void LCD3310_init(void)
{
LCD3310_write_cmd(0x21);
LCD3310_write_cmd(0xd7);
LCD3310_write_cmd(0x06);
LCD3310_write_cmd(0x20);
LCD3310_write_cmd(0x0c);
}
void LCD3310_set_XY(unsigned char x,unsigned char y)
{
if (x >= 84) return;
if (y >= 6) return;
LCD3310_write_cmd(0x80 | x);
LCD3310_write_cmd(0x40 | y);
}
void LCD3310_print(unsigned char n)
{
n = (n << 2) + n;
LCD3310_write_dat(Font[n]);
LCD3310_write_dat(Font[++n]);
LCD3310_write_dat(Font[++n]);
LCD3310_write_dat(Font[++n]);
LCD3310_write_dat(Font[++n]);
}

复制代码

伏尔加的鱼 · 2012-12-28 22:44:25

厉害啊

张明明699 · 2012-12-28 22:50:23

牛人一个

2012-12-28 22:56:17

楼主牛逼啊！！！！

yuying2015 · 2012-12-28 22:56:39

侯s · 2012-12-28 23:06:28

牛逼

包先生 · 2012-12-28 23:10:10

牛逼轰轰的

尹建生 · 2012-12-28 23:16:57

好牛啊

罗永锋 · 2012-12-28 23:18:16

给力

lehi · 2012-12-28 23:19:14

泪隐晨 · 2012-12-28 23:35:54

楼主厉害~~

asdg · 2012-12-29 00:55:49

相当给力

疾风逐浪 · 2012-12-29 08:19:53

膜拜一下！

meiyaolei · 2012-12-29 08:39:41

不错记号了

王子晨 · 2012-12-29 08:48:19

好厉害

于建立 · 2012-12-29 08:48:39

右边那一串电路电容是音频输出电路么？？？？？？？

仰望星空99 · 2012-12-29 09:41:22

牛人

孙润宜 · 2012-12-29 09:54:36

很好资料齐全

李佑兴 · 2012-12-29 09:58:39

膜拜

什么时候我也能达到这种境界？

ahljj123 · 2012-12-29 10:41:49

Hadeshua · 2012-12-29 11:04:47

高手，学习！

搜索历史

单片2051+SD卡和3310做的音乐播放器

相关推荐

246 条评论

评论

精选推荐

热门帖

站长推荐 /6