[电子杂谈]

PWM直流电机调速

2014-7-20 17:27:22 2791

1 ******************************************************************/ / 程序名：PWM直流电机调速 / / 晶振：11.00592 MHz CPU型号：AT89C51 / / 直流电机的PWM波控制，可以直接的调速从0到20级的调速 / /**************************************************************/ #include #define TH0_TL0 (65536-1000)//设定中断的间隔时长 unsigned char count0 = 50;//低电平的占空比 unsigned char count1 = 0;//高电平的占空比 bit Flag = 1;//电机正反转标志位,1正转，0反转 it Key_add=P2 ^ 0; //电机减速 it Key_dec=P2 ^ 1; //电机加速 it Key_turn=P2 ^ 2; //电机换向 it PWM1=P2^6;//PWM 通道 1，反转脉冲 it PWM2=P2^7;//PWM 通道 2，正转脉冲 unsigned char time_delay; /*********函数声明**********/ void Delay(unsigned char x); void Motor_speed_high(void); void Motor_speed_low(void); void Motor_turn(void); void Timer0_init(void); /************延时处理******************/ void Delay(unsigned char x) { Time_delay = x; while(Time_delay != 0);//等待中断，可减少PWM输出时间间隔 } /***按键处理加pwm占空比，电机加速******/ void Motor_speed_high(void)// { if(Key_add==0) { Delay(10); if(Key_add==0) { count0 += 5; if(count0 >= 100) { count0 = 100; } } while(!Key_add);//等待键松开 } } /**按键处理减pwm占空比，电机减速*/ void Motor_speed_low(void) { if(Key_dec==0) { Delay(10); if(Key_dec==0) { count0 -= 5; if(count0 <= 0) { count0 = 0; } } while(!Key_dec ); } } /********电机正反向控制**********/ void Motor_turn(void) { if(Key_turn == 0) { Delay(10); if(Key_turn == 0) { Flag = ~Flag; } while(!Key_turn); } } /*******定时器0初始化*******/ void Timer0_init(void) { TMOD=0x01; //定时器0工作于方式1 TH0=TH0_TL0/256; TL0=TH0_TL0%256; TR0=1; ET0=1; EA=1; } /*****主函数****************/ void main(void) { Timer0_init(); while(1) { Motor_turn(); Motor_speed_high(); Motor_speed_low(); } } /**********定时0中断处理**************/ void Timer0_int(void) interrupt 1 using 1 { TR0 = 0;//设置定时器初值期间，关闭定时器 TL0 = TH0_TL0 % 256; TH0 = TH0_TL0 / 256 ;//定时器装初值 TR0 = 1; if(Time_delay != 0)//延时函数用 { Time_delay--; } if(Flag == 1)//电机正转 { PWM1 = 0; if(++count1 < count0) { PWM2 = 1; } else PWM2 = 0; if(count1 >= 100) { count1=0; } } else //电机反转 { PWM2 = 0; if(++count1 < count0) { PWM1 = 1; } else PWM1 = 0; if(count1 >= 100) { count1=0; } } } //----------------------------------------------------------------------------- #include // SFR declarations #include // Function Prototypes //----------------------------------------------------------------------------- #define CMD_RESET 0xA4 //HD7279复位 #define DECODE1 0xc8 //方式0译码 it cs=P1^3; it clk=P1^2; it dat=P1^1; it key=P1^0; it led_D1003=P0^7; it sw1=P1^7; it sw2=P1^6; it sw3=P1^5; it sw4=P1^4; void long_delay(void); //延时函数 void short_delay(void); void delay10ms(unsigned char); void write7279(unsigned char,unsigned char); //HD7279写指令 void send_byte(unsigned char); void delay(unsigned char); void disp1(unsigned int); void OSCILLATOR_Init (void); void PORT_Init (void); void PCA0_Init (void); void Timer0_Init(void); void Ext_Interrupt_Init (void); //----------------------------------------------------------------------------- // Global Variables //----------------------------------------------------------------------------- //----------------------------------------------------------------------------- // main() Routine //----------------------------------------------------------------------------- unsigned int CEX0_Compare_Value; // Holds current PCA compare value unsigned int tmr,Speed_evaluate; unsigned char num,num1,num2,num3,a; unsigned int Speed,pi,Speed2; unsigned int Speed1[10]; typedef struct { double SetPoint; / 设定目标Desired Value / double Proportion; / 比例常数Proportional Const / double Integral; / 积分常数Integral Const / double Derivative; / 微分常数 Derivative Const / double LastError; / 前一项误差/ double PrevError; / 前第二项误差/ double SumError; / 误差和/ } PID; double PIDCalc( PID pp, double NextPoint ) { double dError,Error,Pout; Error = pp->SetPoint - NextPoint; /* ?????? / pp->SumError += Error; / ??????/ dError = pp->LastError - pp->PrevError; /* ???? / pp->PrevError = pp->LastError; pp->LastError = Error; / ??????? / Pout= pp->Proportion Error + pp->Integral * pp->SumError + pp->Derivative * dError ; if(Pout>1100) Pout=1000; if(Pout<100) Pout=100; return (Pout); } PID sPID; //定义PID结构体变量 double rOut; //PID响应输出 unsigned char rIn; //设置PID反馈值 double x; double sumout; unsigned char dd; //设置PID输出 void main (void) { sPID.Proportion = 0.44; //设置P sPID.Integral = 0.70; //设置I sPID.Derivative = 0.0; //设置D //sPID.SetPoint = CEX0_Compare_Value; //sPID.SetPoint = CEX0_Compare_Value; //设置PID输出 PCA0MD = 0x00; // Disable watchdog timer led_D1003=0; PORT_Init (); // Initialize cros***ar and GPIO OSCILLATOR_Init (); // Initialize oscillator PCA0_Init (); // Initialize PCA0 IP=0x82; //定时器中断0高于外部中断0 Timer0_Init(); Ext_Interrupt_Init (); for (tmr=0;tmr<0x2000;tmr++); send_byte(CMD_RESET);//HD7279复位// Globally enable interrupts EA = 1; sPID.SetPoint=70; while (1) { delay10ms(100); //键盘程序 ------------------------------------------------------------- if(sw1==0) //按键1是否按下 { if(sw1==0)//再次检查按键 { num++; //若按键按下，num加1 if(num==1) //到9归0 { num=0; } while(sw1==0);//按键释放 } // delay10ms(100); } write7279(DECODE1+4,num); //将num写入HD7279第1位 delay10ms(1); if(sw2==0) { if(sw2==0) { num1++; if(num1==2) { num1=0; } while(!sw2); } // delay10ms(100); } 6
2014-7-20 17:27:22　　评论淘帖0 举报相关推荐 • PWM直流电机调速 89 • pwm控制电机正反转，PWM直流电机调速程序 20399 • 单片机综合实验-PWM直流电机调速 20 • 单片机控制PWM的直流电机调速系统的设计 104 • 51单片机实现PWM直流电机调速(注释详细） 250 • LM324构成的PWM直流电机调速电路 14719 • 简单脉冲控制（PWM）直流电机调速电路方案 28564 • 51单片机PWM直流电机调速 3 • 单片机控制PWM的直流电机调速系统的设计 139 • TL494搭建的PWM直流电机调速电路 14053