[问答]

【NanoPi2试用体验】进不去系统求助

7097

问答对人有帮助，内容完整，我也想知道答案 0 ` 【NanoPi2试用体验】进不去系统求助话说离写上一篇帖子已经很长的时间了，由于最近学校组织参加了全国机械大赛，我作为控制系统的的开发人员，也跟上打了几天酱油，所以很久没有发帖了，还希望大家多多包涵，上次说了，神器的确是很棒的，上网放视频都没有卡顿，比起曾经玩过野火的板子，那直接可以说是天上地下吧。回来后，直接奔着板子就准备好好玩一下，习惯的上电后，但是这次却没有正常启动，我也不知道怎么回事，现在把从串口打印出的信息贴出来，让大神瞧瞧，到底是怎么回事了，我已经折腾了一天半了，实在无能为力了。这是烧安卓后的界面，一直显示这样。 ------------------------------------------------------------------------------- Second Boot by Nexell Co. : Ver0.6.1 - Built on Oct 16 2015 13:42:17 -------------------------------------------------------------------------------- EMA VALUE : 001 123 Lock value = 157 GATE CYC = 0x00008421 GATE CODE = 0x3A3A3A3A Read DQ = 0x08080808 Write DQ = 0x08080808 Loading from sdmmc... Image Loading Done! Launch to 0x42C00000 U-Boot 2014.07-gb44132b (Jan 19 2016 - 17:35:14) PLL : [0] = 550000000, [1] = 800000000, [2] = 800000000, [3] = 614399000 PLL1: CPU FCLK = 800000000, HCLK = 200000000 PLL2: BUS BCLK = 400000000, PCLK = 200000000 PLL2: MEM MCLK = 800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000 PLL0: G3D BCLK = 550000000 PLL2: MPG BCLK = 400000000, PCLK = 200000000 I2C: ready DRAM: 256 MiB Heap = 0x43000000~0x45000000 Code = 0x42c00000~0x42c73984 GLD = 0x42bffeb8 GLBD = 0x42bffe68 SP = 0x42bffe68,0x42bffe50(CURR) PC = 0x42c06114 TAGS = 0x40000100 PAGE = 0x42c80000~0x42c8c000 MACH = [4330] VER = 1 BOARD= [nanopi2] LCD = X710 MMC: NXP DWMMC: 0, NXP DWMMC: 1, NXP DWMMC: 2 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device RGB: display.0 DISP: W=1024, H= 600, Bpp=32 DONE: Logo bmp 800 by 480 (3bpp), len=1152056 DRAW: 0x47000000 -> 0x46000000 Hit any key to stop autoboot: 0 ## Booting kernel from Legacy Image at 48000000 ... Image Name: Linux-3.4.39-s5p4418 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4392288 Bytes = 4.2 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4.39-s5p4418 (root@jensen) (gcc version 4.9.3 (ctng-1.21.0-229g-FA) ) #104 SMP PREEMPT Fri Apr 15 16:54:19 HKT 2016 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: NANOPI2 [ 0.000000] Display: X710 selected [ 0.000000] nxp_reserve_mem: reserve CMA: size 201326592 [ 0.000000] NXP/CMA: Reserved 0x63600000/0x0c000000 for 'ion' [ 0.000000] NXP/CMA: success register cma region for 'ion' [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000 [ 0.000000] CPU : iomap[ 1]: p 0xf0000000 -> v 0xf0300000 len=0x100000 [ 0.000000] CPU : iomap[ 2]: p 0xcf000000 -> v 0xf0400000 len=0x100000 [ 0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000 [ 0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000 [ 0.000000] CPU : DMA Zone Size =16M, CORE 4 [ 0.000000] CPU : VERSION = 2 (0xE153000A), Assign Peripheral Exclusive Bus [ 0.000000] s5p4418-NanoPi2: Board initialized [ 0.000000] CPU : Clock Generator= 64 EA, DVFS = support, PLL.1 [ 0.000000] PLL : [0] = 550000000, [1] = 800000000, [2] = 800000000, [3] = 614399000 [ 0.000000] PLL1: CPU FCLK = 800000000, HCLK = 200000000 [ 0.000000] PLL2: BUS BCLK = 400000000, PCLK = 200000000 [ 0.000000] PLL2: MEM MCLK = 800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000 [ 0.000000] PLL0: G3D BCLK = 550000000 [ 0.000000] PLL2: MPG BCLK = 400000000, PCLK = 200000000 [ 0.000000] PERCPU: Embedded 9 pages/cpu @c127f000 s12352 r8192 d16320 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259839 [ 0.000000] Kernel command line: console=ttyAMA0,115200n8 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait init=/*in/init systemd.show_status=false g_ether.host_addr=82:cf:ce:fa:44:18 initrd=0x49000000,0x400000 console=tty1 lcd=X710 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] allocated 2097152 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 1024MB = 1024MB total [ 0.000000] Memory: 825932k/825932k available, 222644k reserved, 272384K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xef800000 - 0xfee00000 ( 246 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef600000 ( 758 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc07e2fec (8044 kB) [ 0.000000] .init : 0xc07e3000 - 0xc081a040 ( 221 kB) [ 0.000000] .data : 0xc081c000 - 0xc089a600 ( 506 kB) [ 0.000000] .bss : 0xc089a624 - 0xc0975498 ( 876 kB) [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:288 [ 0.000000] VIC @f0002000: id 0x00041192, vendor 0x41 [ 0.000000] VIC @f0003000: id 0x00041192, vendor 0x41 [ 0.000000] GPIO @f001a000: start 64, mask 0xffffffff (gpio 53) [ 0.000000] GPIO @f001b000: start 96, mask 0xffffffff (gpio 54) [ 0.000000] GPIO @f001c000: start 128, mask 0xffffffff (gpio 55) [ 0.000000] GPIO @f001d000: start 160, mask 0xffffffff (gpio 56) [ 0.000000] GPIO @f001e000: start 192, mask 0xffffffff (gpio 57) [ 0.000000] ALIVE @f0010800: start 224, mask 0x000000ff (alive 4) [ 0.000000] GIC @f0301000: start 256 (vic 31) [ 0.000000] timer.0: source, 10000000(HZ:250), mult:3355443200 [ 0.000000] timer.1: event , 10000000(HZ:250), mult:42949673 [ 0.000000] sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 4294967292ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty1] enabled [ 0.000000] Calibrating delay loop... 1594.36 BogoMIPS (lpj=3188736) [ 0.048000] pid_max: default: 32768 minimum: 301 [ 0.048000] Security Framework initialized [ 0.048000] SELinux: Initializing. [ 0.048000] Mount-cache hash table entries: 512 [ 0.048000] Initializing cgroup subsys cpuacct [ 0.048000] Initializing cgroup subsys memory [ 0.048000] Initializing cgroup subsys devices [ 0.048000] Initializing cgroup subsys freezer [ 0.048000] CPU: Testing write buffer coherency: ok [ 0.048000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00 [ 0.048000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.048000] Setting up static identity map for 0x405df8d0 - 0x405df928 [ 0.048000] L310 cache controller enabled [ 0.048000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x70470001, Cache size: 1048576 B [ 0.092000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01 [ 0.132000] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02 [ 0.172000] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03 [ 0.176000] Brought up 4 CPUs [ 0.176000] SMP: Total of 4 processors activated (6377.47 BogoMIPS). [ 0.176000] devtmpfs: initialized [ 0.180000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.184000] pwm: max = 50000000 hz [ 0.184000] prepare_gpio_suspend: [ 0.184000] alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000 [ 0.184000] alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566 [ 0.184000] alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555 [ 0.184000] alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000 [ 0.184000] alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000 [ 0.184000] dummy: [ 0.184000] NET: Registered protocol family 16 [ 0.184000] [Register machine platform devices] [ 0.184000] mach: add amba device uart-pl011.0 [ 0.184000] mach: add amba device uart-pl011.1 [ 0.184000] mach: add amba device uart-pl011.3 [ 0.184000] mach: add amba device uart-pl011.4 [ 0.184000] mach: add amba device pl08xdmac.0 [ 0.184000] mach: add amba device pl08xdmac.1 [ 0.184000] mach: add amba device ssp-pl022.0 [ 0.188000] mach: add device syncgen [2] [ 0.188000] mach: add device lcd [ 0.188000] mach: add device i2c bus (array:3) [ 0.188000] mach: add device Real Time Clock [ 0.188000] mach: add device generic pwm (array:4) [ 0.188000] mach: add device generic gpio (array:6) [ 0.188000] mach: add device i2s (array:1) [ 0.188000] mach: add device spdif tx [ 0.188000] mach: add device u_ehci [ 0.188000] mach: add device u_ohci [ 0.188000] mach: add device u* otg [ 0.188000] mach: add device ion-nxp [ 0.188000] mach: add device adc [ 0.188000] mach: add graphic device opengl\|es [ 0.188000] [Register board platform devices] [ 0.188000] plat: board revision 5 [ 0.188000] plat: add dynamic frequency (pll.1) [ 0.188000] plat: add device adc temp [ 0.188000] plat: add framebuffer [ 0.188000] plat: boot from mmc.0 [ 0.188000] plat: add device sdmmc [0] [ 0.192000] plat: add backlight pwm device [ 0.192000] plat: add device keypad [ 0.192000] plat: add device spdif playback [ 0.192000] plat: add device asoc-es8316 [ 0.192000] plat: add device nxp-v4l2 [ 0.192000] plat: register spidev [ 0.192000] plat: add touch(ft5x0x) device [ 0.192000] plat: add touch(it7260) device [ 0.192000] plat: add onewire ts device [ 0.192000] plat: add adxl34x device [ 0.192000] plat: add bmp085 device [ 0.192000] plat: add ds1307 device [ 0.192000] plat: add pcf8591 device [ 0.192000] plat: add device nxp-gmac [ 0.196000] plat: add device gpio_led [ 0.196000] plat: add device pwm_led [ 0.196000] [ 0.196000] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.196000] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.196000] Serial: AMBA PL011 UART driver [ 0.196000] uart-pl011.0: ttyAMA0 at MMIO 0xc00a1000 (irq = 7) is a PL011 rev3 [ 0.200000] console [ttyAMA0] enabled [ 0.204000] uart-pl011.1: ttyAMA1 at MMIO 0xc00a0000 (irq = 6) is a PL011 rev3 [ 0.208000] uart-pl011.3: ttyAMA2 at MMIO 0xc00a3000 (irq = 9) is a PL011 rev3 [ 0.212000] uart-pl011.4: ttyAMA3 at MMIO 0xc006d000 (irq = 10) is a PL011 rev3 [ 0.236000] bio: create slab at 0 [ 0.240000] gpiochip_add: registered GPIOs 0 to 31 on device: nxp-gpio.0 [ 0.248000] gpiochip_add: registered GPIOs 32 to 63 on device: nxp-gpio.1 [ 0.252000] gpiochip_add: registered GPIOs 64 to 95 on device: nxp-gpio.2 [ 0.256000] gpiochip_add: registered GPIOs 96 to 127 on device: nxp-gpio.3 [ 0.260000] gpiochip_add: registered GPIOs 128 to 159 on device: nxp-gpio.4 [ 0.264000] gpiochip_add: registered GPIOs 160 to 167 on device: nxp-gpio.5 [ 0.268000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable! [ 0.272000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels [ 0.276000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels [ 0.284000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 1 [ 0.288000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable! [ 0.292000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels [ 0.296000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels [ 0.300000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 2 [ 0.304000] nxp_ion_probe success!!! [ 0.308000] SCSI subsystem initialized [ 0.312000] ssp-pl022 ssp-pl022.0: ARM PL022 driver, device ID: 0x00041022 [ 0.316000] pl022: mapped registers from 0xc005b000 to f005b000 [ 0.320000] ssp-pl022 ssp-pl022.0: setup for DMA on RX dma1chan7, TX dma1chan6 [ 0.324000] ssp-pl022 ssp-pl022.0: will use autosuspend for runtime pm, delay 10ms [ 0.328000] u*core: registered new interface driver ufs [ 0.332000] ucore: registered new interface driver hub [ 0.336000] ucore: registered new device driver u** [ 0.340000] i2c-gpio i2c-gpio.3: using pins 159 (SDA) and 158 (SCL) [ 0.344000] nxp-i2c.0: 390625 hz [pclk=200000000, clk = 256, scale= 1, timeout= 500 ms] [ 0.348000] nxp-i2c.1: 97656 hz [pclk=200000000, clk = 256, scale= 7, timeout= 500 ms] [ 0.352000] nxp-i2c.2: 195312 hz [pclk=200000000, clk = 256, scale= 3, timeout= 500 ms] [ 0.356000] Linux media interface: v0.10 [ 0.360000] Linux video capture interface: v2.00 [ 0.364000] pps_core: LinuxPPS API ver. 1 registered [ 0.368000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.372000] PTP clock support registered [ 0.380000] axp_mfd 3-0034: AXP (CHIP ID: 0x06) detected [ 0.388000] axp22_ldo1: 3000 mV [ 0.396000] axp22_aldo1: 700 <--> 3300 mV at 3300 mV [ 0.404000] axp22_aldo2: 700 <--> 3300 mV at 1800 mV [ 0.412000] axp22_aldo3: 700 <--> 3300 mV at 1000 mV [ 0.420000] axp22_dldo1: 700 <--> 3300 mV at 3300 mV [ 0.428000] axp22_dldo2: No configuration [ 0.432000] axp22_dldo2: 700 <--> 3300 mV at 700 mV [ 0.436000] axp22_dldo3: No configuration [ 0.444000] axp22_dldo3: 700 <--> 3300 mV at 700 mV [ 0.448000] axp22_dldo4: No configuration [ 0.452000] axp22_dldo4: 700 <--> 3300 mV at 700 mV [ 0.460000] axp22_eldo1: 700 <--> 3300 mV at 1800 mV [ 0.468000] axp22_eldo2: 700 <--> 3300 mV at 3300 mV [ 0.476000] axp22_eldo3: No configuration [ 0.480000] axp22_eldo3: 700 <--> 3300 mV at 700 mV [ 0.484000] axp22_dc5ldo: No configuration [ 0.492000] axp22_dc5ldo: 700 <--> 1400 mV at 1200 mV [ 0.500000] axp22_dcdc1: 1600 <--> 3400 mV at 3300 mV [ 0.508000] axp22_dcdc2: 600 <--> 1540 mV at 1200 mV [ 0.516000] axp22_dcdc3: 600 <--> 1860 mV at 1200 mV [ 0.524000] axp22_dcdc4: 600 <--> 1540 mV at 1500 mV [ 0.532000] axp22_dcdc5: 1000 <--> 2550 mV at 1500 mV [ 0.540000] axp22_ldoio0: 700 <--> 3300 mV at 3800 mV [ 0.548000] axp22_ldoio1: 700 <--> 3300 mV at 3800 mV [ 0.552000] Advanced Linux Sound Architecture Driver Version 1.0.25. [ 0.556000] Switching to clocksource source timer [ 0.580000] NET: Registered protocol family 2 [ 0.588000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.596000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.604000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 0.612000] TCP: Hash tables configured (established 131072 bind 65536) [ 0.620000] TCP: reno registered [ 0.620000] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.628000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.636000] NET: Registered protocol family 1 [ 0.640000] RPC: Registered named UNIX socket transport module. [ 0.644000] RPC: Registered udp transport module. [ 0.652000] RPC: Registered tcp transport module. [ 0.656000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.660000] Unpacking initramfs... [ 0.840000] Initramfs unpacking failed: junk in compressed archive [ 0.856000] Freeing initrd memory: 4096K [ 0.860000] Disply Reset Status : On [ 0.864000] Display LCD register operation [ 0.868000] Display.0 fps=61 (16 ms), wait= 6 jiffies, Pixelclk=50000000hz [ 0.876000] LCD : [1]=LCD connect to [5]=SYNCGEN0 [ 0.880000] audit: initializing netlink socket (disabled) [ 0.884000] type=2000 audit(0.884:1): initialized [ 0.892000] highmem bounce pool size: 64 pages [ 0.904000] NFS: Registering the id_resolver key type [ 0.908000] fuse init (API version 7.18) [ 0.916000] msgmni has been set to 1089 [ 0.920000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.928000] io scheduler noop registered [ 0.932000] io scheduler deadline registered [ 0.936000] io scheduler cfq registered (default) [ 0.940000] display.0 connected to fb.0 ... [ 0.944000] nxp-fb.0: dma addr = 0x63600000, buf[0xe32d6e80] [ 0.952000] nxp-fb.0: dma addr = 0x63858000, buf[0xe32d7040] [ 1.020000] nxp-fb 0: out[0], 1024 * 600 - 32 bpp (phys:63600000 virt:0xef831000 max:4915200) [ 1.040000] Console: switching to colour frame buffer device 128x37 [ 1.064000] uart-pl011 uart-pl011.0: no DMA platform data [ 1.068000] uart-pl011 uart-pl011.1: no DMA platform data [ 1.076000] uart-pl011 uart-pl011.3: no DMA platform data [ 1.080000] uart-pl011 uart-pl011.4: no DMA platform data [ 1.088000] loop: module loaded [ 1.092000] tun: Universal TUN/TAP device driver, 1.6 [ 1.100000] tun: (C) 1999-2004 Max Krasnyansky [ 1.108000] -- nxpmac initialize -- [ 1.116000] stmmac - user ID: 0x37, Synopsys ID: 0x37 [ 1.124000] Ring mode enabled [ 1.132000] DMA HW capability register supported [ 1.136000] Enhanced/Alternate descriptors [ 1.148000] Enabled extended descriptors [ 1.156000] RX Checksum Offload Engine supported (type 2) [ 1.164000] TX Checksum insertion supported [ 1.172000] Wake-Up On Lan supported [ 1.180000] Enable RX Mitigation via HW Watchdog Timer [ 1.236000] stmmac: probed [ 1.240000] eth0: PHY ID 001cc915 at 0 IRQ 215 (stmmac-0:00) [ 1.252000] eth0: PHY ID 001cc915 at 7 IRQ 215 (stmmac-0:07) active [ 1.260000] PPP generic driver version 2.4.2 [ 1.268000] PPP BSD Compression module registered [ 1.276000] PPP Deflate Compression module registered [ 1.292000] PPP MPPE Compression module registered [ 1.300000] NET: Registered protocol family 24 [ 1.308000] u*core: registered new interface driver asix [ 1.320000] ucore: registered new interface driver cdc_ether [ 1.328000] ucore: registered new interface driver net1080 [ 1.336000] ucore: registered new interface driver cdc_subset [ 1.344000] ucore: registered new interface driver zaurus [ 1.356000] ucore: registered new interface driver cdc_ncm [ 1.364000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.372000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller [ 1.384000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1 [ 1.392000] nxp-ehci nxp-ehci: irq 50, io mem 0xc0030000 [ 1.412000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00 [ 1.420000] u u1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.428000] u u1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.440000] u u1: Product: SLsi Synopsys EHCI Host Controller [ 1.448000] u u1: Manufacturer: Linux 3.4.39-s5p4418 ehci_hcd [ 1.456000] u u1: SerialNumber: nxp-ehci [ 1.464000] hub 1-0:1.0: USB hub found [ 1.472000] hub 1-0:1.0: 3 ports detected [ 1.480000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus) [ 1.688000] Core Release: 2.93a [ 1.696000] Setting default values for core params [ 1.704000] Finished setting default values for core params [ 1.792000] u 1-1: new high-speed USB device number 2 using nxp-ehci [ 1.912000] Using Descriptor DMA mode [ 1.920000] Dedicated Tx FIFOs mode [ 1.928000] dwc_otg dwc_otg: DWC OTG Controller [ 1.932000] u* 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 1.932000] u* 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.932000] u* 1-1: Product: USB2.0 Hub [ 1.932000] hub 1-1:1.0: USB hub found [ 1.932000] hub 1-1:1.0: 4 ports detected [ 1.976000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2 [ 1.988000] dwc_otg dwc_otg: irq 49, io mem 0x00000000 [ 1.996000] u* u2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.004000] u u2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.016000] u u2: Product: DWC OTG Controller [ 2.024000] u u2: Manufacturer: Linux 3.4.39-s5p4418 dwc_otg_hcd [ 2.036000] u u2: SerialNumber: dwc_otg [ 2.044000] hub 2-0:1.0: USB hub found [ 2.052000] hub 2-0:1.0: 1 port detected [ 2.056000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.068000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller [ 2.076000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3 [ 2.088000] nxp-ohci nxp-ohci: irq 50, io mem 0xc0020000 [ 2.156000] u u3: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.164000] u u3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.176000] u u3: Product: SLsi Synopsys OHCI Host Controller [ 2.184000] u u3: Manufacturer: Linux 3.4.39-s5p4418 ohci_hcd [ 2.196000] u u3: SerialNumber: nxp-ohci [ 2.204000] hub 3-0:1.0: USB hub found [ 2.208000] u 1-1.2: new full-speed USB device number 3 using nxp-ehci [ 2.224000] hub 3-0:1.0: 3 ports detected [ 2.232000] Initializing USB Mass Storage driver... [ 2.240000] ucore: registered new interface driver u-storage [ 2.248000] USB Mass Storage support registered. [ 2.256000] ucore: registered new interface driver userial [ 2.268000] ucore: registered new interface driver userial_generic [ 2.276000] USB Serial support registered for generic [ 2.308000] u* 1-1.2: New USB device found, idVendor=1d57, idProduct=fa60 [ 2.320000] u* 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.332000] u* 1-1.2: Product: 2.4G Receiver [ 2.340000] u* 1-1.2: Manufacturer: Compx [ 2.348000] userial: USB Serial Driver core [ 2.356000] ucore: registered new interface driver ftdi_sio [ 2.368000] USB Serial support registered for FTDI USB Serial Device [ 2.376000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver [ 2.388000] ucore: registered new interface driver option [ 2.396000] USB Serial support registered for GSM modem (1-port) [ 2.408000] ucore: registered new interface driver pl2303 [ 2.416000] USB Serial support registered for pl2303 [ 2.424000] g_ether gadget: using random self ethernet address [ 2.436000] u0: MAC 16:01:aa:54:d3:f9 [ 2.444000] u0: HOST MAC 82:cf:ce:fa:44:18 [ 2.452000] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 [ 2.464000] g_ether gadget: g_ether ready [ 2.472000] mousedev: PS/2 mouse device common for all mice [ 2.480000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0 [ 2.492000] ucore: registered new interface driver xpad [ 2.500000] Fail, arbit i2c.2 addr [0x8c] data[0x8d], trans[ 0: 1] [ 2.512000] i2c.2 addr 0x8c (try:1) [ 2.524000] IT7260-ts 2-0046: Found chip ITE726060 [ 2.532000] input: it7260_ts as /devices/virtual/input/input1 [ 2.540000] i2c-core: driver [IT7260-ts] using legacy suspend method [ 2.552000] i2c-core: driver [IT7260-ts] using legacy resume method [ 2.564000] touchscreen-1wire initialized [ 2.572000] backlight-1wire initialized [ 2.580000] input: fa_ts_input as /devices/virtual/input/input2 [ 2.588000] ts-if initialized [ 2.596000] [RTC] day=2016.01.01 time=08:28:36 [ 2.604000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0 [ 2.616000] i2c /dev entries driver [ 2.624000] lirc_dev: IR Remote Control driver registered, major 248 [ 2.636000] IR NEC protocol handler initialized [ 2.644000] IR RC5(x) protocol handler initialized [ 2.652000] IR RC6 protocol handler initialized [ 2.660000] IR JVC protocol handler initialized [ 2.668000] IR Sony protocol handler initialized [ 2.676000] IR RC5 (streamzap) protocol handler initialized [ 2.688000] IR SANYO protocol handler initialized [ 2.696000] IR LIRC bridge handler initialized [ 2.704000] gspca_main: v2.14.0 registered [ 2.716000] ...................................ov5640_probe 2234 [ 2.728000] ...................................ov5640_video_probe 2193 [ 2.736000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2] [ 2.748000] i2c.0 addr 0x78 (try:1) [ 2.756000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2] [ 2.764000] i2c.0 addr 0x78 (try:2) [ 2.772000] Error: i2c.0, addr:78, trans len:-11(2), try:2 [ 2.780000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2] [ 2.792000] i2c.0 addr 0x78 (try:1) [ 2.800000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2] [ 2.808000] i2c.0 addr 0x78 (try:2) [ 2.816000] Error: i2c.0, addr:78, trans len:-11(2), try:2 [ 2.828000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2] [ 2.836000] i2c.0 addr 0x78 (try:1) [ 2.844000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2] [ 2.852000] i2c.0 addr 0x78 (try:2) [ 2.860000] Error: i2c.0, addr:78, trans len:-11(2), try:2 [ 2.872000] ov5640 0-003c: reg_read: i2c read error, reg: 300a [ 2.880000] OV5640 read error!!!!!!!!!!!!!!! [ 2.888000] ov5640_initialize_ctrls.............1794........... [ 2.904000] ucore: registered new interface driver uvcvideo [ 2.916000] USB Video Class driver (1.1.1) [ 2.924000] Driver for 1-wire Dallas network protocol. [ 2.932000] device-mapper: uevent: version 1.0.3 [ 2.940000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com [ 2.956000] DVFS: ASV[0] IDS(10mA, 8) Ro(110, 98) [ 2.968000] DVFS: regulator vdd_arm_1.3V [ 2.976000] DVFS: cpu DVFS with PLL.1 [tables=8] [ 2.984000] cpuidle: using governor ladder [ 2.992000] cpuidle: using governor menu [ 3.000000] Synopsys Designware Multimedia Card Interface Driver [ 3.008000] dw_mmc dw_mmc.0: Using internal DMA controller. [ 3.020000] mmc0: no vmmc regulator found [ 3.028000] dw_mmc dw_mmc.0: Using external card detect irq 225 (io 161) [ 3.040000] dw_mmc dw_mmc.0: Version ID is 250a [ 3.048000] dw_mmc dw_mmc.0: DW MMC controller at irq 43, 32 bit host data width, 32 deep fifo hw timeout 500 ms [ 3.056000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.072000] input: Compx 2.4G Receiver as /devices/platform/nxp-ehci/u1/1-1/1-1.2/1-1.2:1.0/input/input3 [ 3.088000] generic-u 0003:1D57:FA60.0001: input,hidraw0: USB HID v1.01 Keyboard [Compx 2.4G Receiver] on u-nxp-ehci-1.2/input0 [ 3.104000] input: Compx 2.4G Receiver as /devices/platform/nxp-ehci/u1/1-1/1-1.2/1-1.2:1.1/input/input4 [ 3.112000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 3.112000] mmc0: new high speed SDHC card at address 0001 [ 3.112000] mmcblk0: mmc0:0001 SD 7.43 GiB [ 3.112000] mmcblk0: p1 p2 [ 3.152000] generic-u* 0003:1D57:FA60.0002: input,hidraw1: USB HID v1.01 Mouse [Compx 2.4G Receiver] on u*-nxp-ehci-1.2/input1 [ 3.192000] input: Compx 2.4G Receiver as /devices/platform/nxp-ehci/u1/1-1/1-1.2/1-1.2:1.2/input/input5 [ 3.204000] generic-u 0003:1D57:FA60.0003: input,hidraw2: USB HID v1.01 Device [Compx 2.4G Receiver] on u-nxp-ehci-1.2/input2 [ 3.220000] ucore: registered new interface driver uhid [ 3.228000] u*hid: USB HID core driver [ 3.240000] ADC: CHs 8, 200000(1000000 ~ 130208) sample rate, polling mode, scale=166(bit 6) [ 3.252000] snd pcm: register sound platform 'nxp-pcm' [ 3.260000] snd i2s: ch 0, master, iis mode, 48000(47999)hz, 32 FBITs, MCLK=12287980hz, RFS=256 [ 3.388000] asoc: ES8316 HiFi <-> nxp-i2s.0 mapping ok [ 3.408000] spdif-tx: 48000(47348)Hz, MCLK=12121212hz HDMI out [ 3.416000] asoc: dit-hifi <-> nxp-spdif-tx mapping ok [ 3.428000] GACT probability NOT on [ 3.432000] Mirror/redirect action on [ 3.440000] u32 classifier [ 3.444000] Actions configured [ 3.452000] Netfilter messages via NETLINK v0.30. [ 3.460000] nf_conntrack version 0.5.0 (12969 buckets, 51876 max) [ 3.472000] ctnetlink v0.93: registering with nfnetlink. [ 3.480000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 3.488000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 3.500000] xt_time: kernel timezone is -0000 [ 3.508000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.516000] arp_tables: (C) 2002 David S. Miller [ 3.524000] TCP: cubic registered [ 3.528000] Initializing XFRM netlink socket [ 3.536000] NET: Registered protocol family 10 [ 3.544000] Mobile IPv6 [ 3.552000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.560000] IPv6 over IPv4 tunneling driver [ 3.568000] NET: Registered protocol family 17 [ 3.576000] NET: Registered protocol family 15 [ 3.584000] NET: Registered protocol family 35 [ 3.588000] Registering the dns_resolver key type [ 3.596000] Registering SWP/SWPB emulation handler [ 3.608000] axp22_dcdc5: incomplete constraints, leaving on [ 3.616000] axp22_dcdc4: incomplete constraints, leaving on [ 3.624000] axp22_dcdc3: incomplete constraints, leaving on [ 3.636000] axp22_dcdc2: incomplete constraints, leaving on [ 3.644000] axp22_dcdc1: incomplete constraints, leaving on [ 3.652000] axp22_dc5ldo: incomplete constraints, leaving on [ 3.660000] axp22_eldo2: incomplete constraints, leaving on [ 3.668000] axp22_eldo1: incomplete constraints, leaving on [ 3.680000] axp22_dldo1: incomplete constraints, leaving on [ 3.688000] axp22_aldo3: incomplete constraints, leaving on [ 3.696000] axp22_aldo2: incomplete constraints, leaving on [ 3.704000] axp22_aldo1: incomplete constraints, leaving on [ 3.712000] otg_wakelock_init: No USB transceiver found [ 3.720000] nxp-rtc nxp-rtc.0: setting system clock to 2016-01-01 08:28:37 UTC (1451636917) [ 3.732000] TMU: register adc.2 to hwmon [ 3.736000] ALSA device list: [ 3.740000] #0: I2S-ES8316 [ 3.744000] #1: SPDIF-Transciever [ 3.752000] Freeing init memory: 220K [ 3.756000] Write protecting the kernel text section c0008000 - c07b5000 [ 3.764000] rodata_test: attempting to write to read-only section: [ 3.772000] write to read-only section trapped, success 复制代码* 这是串口打印出的信息，希望哪位大神解答一下，补充内容 (2016-5-22 10:16): 这个吧型号写错了，重新发了一个` 0 已退回2积分
2016-5-21 15:24:04　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × jinyi7016 该类别下有 6 个回答。邀请回答 gjianw217 该类别下有 4 个回答。邀请回答高增华该类别下有 4 个回答。邀请回答曲海洋该类别下有 4 个回答。邀请回答 3w工程师该类别下有 3 个回答。邀请回答 dvd1478 该类别下有 3 个回答。邀请回答 xyq152438 该类别下有 2 个回答。邀请回答辉哥的歌该类别下有 2 个回答。邀请回答愚姬嗳霸王该类别下有 2 个回答。邀请回答 yhyuan 该类别下有 2 个回答。邀请回答 shmily53 该类别下有 2 个回答。邀请回答朱景星该类别下有 2 个回答。邀请回答 SUNROC1 该类别下有 2 个回答。邀请回答王谦该类别下有 2 个回答。邀请回答 lancepang 该类别下有 2 个回答。邀请回答刘乐123 该类别下有 2 个回答。邀请回答风铃阵阵该类别下有 2 个回答。邀请回答落叶不流泪该类别下有 2 个回答。邀请回答 scx2006114 该类别下有 2 个回答。邀请回答 PIXMAV 该类别下有 2 个回答。邀请回答举报 DXK123~ 相关推荐 • 【NanoPi2试用体验】功能篇（1）硬件扩展（NanoPi2的Led入门） 9183 • 【NanoPi2试用体验】基础篇（1）开箱赏板 5597 • 【Nanopi2试用体验】Matrix 为什么没有PWM？ 7617 • NanoPi M3 可以用NanoPi2 的系统吗？ 5524 • 【NanoPi2试用体验】更新NanoPi2板上SD的U-Boot问题 4202 • 【Nanopi2试用体验】初级（二）：LCD转接板设计——求助（完成后分享） 8915 • 【NanoPi2试用体验】nanopi2使用linux i2cdetect失败 6792 • 【NanoPi M2试用体验】+SD卡之小问题（欢迎补充） 8236 • nanopi m2 进不去系统 3777 • 【NanoPi2试用体验】基础篇（3）初体验（安装软件，烧写镜像，系统登录） 14317 2个回答

答案对人有帮助，有参考价值 0 安卓启动的时候回很快进入休眠的，你按那个唤醒的键了吗？我刚开始的时候也是感觉没进去看，但是按led旁边的那个按键就可以了！

2016-5-21 22:11:33 评论举报曲海洋