COG12864标准演示程序

ti

//时序为P6800时序，包括8080时序以及串口方式，不需要用到可以屏蔽掉。

/***************一般连接方法：******************/

// P/S->H:Parallel（并口）; P/S->L:Serial(串口）

//连接电容值都为无极性1uF/25V

// V1--||--VSS （V1和地之间接一电容）

// V3--||--VSS （V3和地之间接一电容）

// C2N--||--C2P （C2负和C2正之间接一电容）

// C1N--||--C3P （C1负和C3正之间接一电容）

//正常工作时，Vout电压约9.0V--11.0V左右

//标准工作电压：3.3V

//输入高电平电压： 0.8 x VDD — VDD V

//显示模式关时标称电流：16 uA

//显示模式关时标称电流：90 uA

//Standby Current 5 uA

/************************************************/

#include

#define uchar unsigned char

***it RES= P3^4;//复位信号

***it R_D= P3^0;//读信号

//串口定义及连接方法：

//D0-D5接地（如果悬空也可以）

***it R_S= P3^5;//指令/数据选择信号

***it SCK= P1^6;

***it C_S= P3^7;//片选

/**********************************************/

void WrateD(uchar dat); //写入数据到LCD程序

void Delayms(uchar ms); //延时程序

void Setadd(uchar xl,uchar yl);//LCD地址设定程序

//取模方式：纵向，字节到序，逗号保留

{

0x20,0xF8,0xF8,0x20,0xF8,0xF8,0x20,0x00,0x02,0x0F,0x0F,0x02,0x0F,0x0F,0x02,0x00, // -#-

0x38,0x7C,0x44,0x47,0x47,0xCC,0x98,0x00,0x03,0x06,0x04,0x1C,0x1C,0x07,0x03,0x00, // -$-

0x30,0x30,0x00,0x80,0xC0,0x60,0x30,0x00,0x0C,0x06,0x03,0x01,0x00,0x0C,0x0C,0x00, // -%-

0x80,0xD8,0x7C,0xE4,0xBC,0xD8,0x40,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -&-

0x00,0x10,0x1E,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -'-

0x00,0x00,0xF0,0xF8,0x0C,0x04,0x00,0x00,0x00,0x00,0x03,0x07,0x0C,0x08,0x00,0x00, // -(-

0x00,0x00,0x04,0x0C,0xF8,0xF0,0x00,0x00,0x00,0x00,0x08,0x0C,0x07,0x03,0x00,0x00, // -)-

0x80,0xA0,0xE0,0xC0,0xC0,0xE0,0xA0,0x80,0x00,0x02,0x03,0x01,0x01,0x03,0x02,0x00, // -*-

0x00,0x80,0x80,0xE0,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x03,0x03,0x00,0x00,0x00, // -+-

0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x1E,0x0E,0x00,0x00,0x00, // -,-

0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // ---

0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x0C,0x00,0x00,0x00, // -.-

0x00,0x00,0x00,0x80,0xC0,0x60,0x30,0x00,0x0C,0x06,0x03,0x01,0x00,0x00,0x00,0x00, // -/-

0xF8,0xFC,0x04,0xC4,0x24,0xFC,0xF8,0x00,0x07,0x0F,0x09,0x08,0x08,0x0F,0x07,0x00, // -0-

0x00,0x10,0x18,0xFC,0xFC,0x00,0x00,0x00,0x00,0x08,0x08,0x0F,0x0F,0x08,0x08,0x00, // -1-

0x08,0x0C,0x84,0xC4,0x64,0x3C,0x18,0x00,0x0E,0x0F,0x09,0x08,0x08,0x0C,0x0C,0x00, // -2-

0x08,0x0C,0x44,0x44,0x44,0xFC,0xB8,0x00,0x04,0x0C,0x08,0x08,0x08,0x0F,0x07,0x00, // -3-

0xC0,0xE0,0xB0,0x98,0xFC,0xFC,0x80,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00, // -4-

0x7C,0x7C,0x44,0x44,0xC4,0xC4,0x84,0x00,0x04,0x0C,0x08,0x08,0x08,0x0F,0x07,0x00, // -5-

0xF0,0xF8,0x4C,0x44,0x44,0xC0,0x80,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -6-

0x0C,0x0C,0x04,0x84,0xC4,0x7C,0x3C,0x00,0x00,0x00,0x0F,0x0F,0x00,0x00,0x00,0x00, // -7-

0xB8,0xFC,0x44,0x44,0x44,0xFC,0xB8,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -8-

0x38,0x7C,0x44,0x44,0x44,0xFC,0xF8,0x00,0x00,0x08,0x08,0x08,0x0C,0x07,0x03,0x00, // -9-

0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x00,0x00,0x00, // -:-

0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,0x08,0x0E,0x06,0x00,0x00,0x00, // -;-

0x00,0x80,0xC0,0x60,0x30,0x18,0x08,0x00,0x00,0x00,0x01,0x03,0x06,0x0C,0x08,0x00, // -<-

0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x00, // -=-

0x00,0x08,0x18,0x30,0x60,0xC0,0x80,0x00,0x00,0x08,0x0C,0x06,0x03,0x01,0x00,0x00, // ->-

0x18,0x1C,0x04,0xC4,0xE4,0x3C,0x18,0x00,0x00,0x00,0x00,0x0D,0x0D,0x00,0x00,0x00, // -?-

0xF0,0xF8,0x08,0xC8,0xC8,0xF8,0xF0,0x00,0x07,0x0F,0x08,0x0B,0x0B,0x0B,0x01,0x00, // -@-

0xE0,0xF0,0x98,0x8C,0x98,0xF0,0xE0,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -A-

0x04,0xFC,0xFC,0x44,0x44,0xFC,0xB8,0x00,0x08,0x0F,0x0F,0x08,0x08,0x0F,0x07,0x00, // -B-

0xF0,0xF8,0x0C,0x04,0x04,0x0C,0x18,0x00,0x03,0x07,0x0C,0x08,0x08,0x0C,0x06,0x00, // -C-

0x04,0xFC,0xFC,0x04,0x0C,0xF8,0xF0,0x00,0x08,0x0F,0x0F,0x08,0x0C,0x07,0x03,0x00, // -D-

0x04,0xFC,0xFC,0x44,0xE4,0x0C,0x1C,0x00,0x08,0x0F,0x0F,0x08,0x08,0x0C,0x0E,0x00, // -E-

0x04,0xFC,0xFC,0x44,0xE4,0x0C,0x1C,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -F-

0xF0,0xF8,0x0C,0x84,0x84,0x8C,0x98,0x00,0x03,0x07,0x0C,0x08,0x08,0x07,0x0F,0x00, // -G-

0xFC,0xFC,0x40,0x40,0x40,0xFC,0xFC,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -H-

0x00,0x00,0x04,0xFC,0xFC,0x04,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -I-

0x00,0x00,0x00,0x04,0xFC,0xFC,0x04,0x00,0x07,0x0F,0x08,0x08,0x0F,0x07,0x00,0x00, // -J-

0x04,0xFC,0xFC,0xC0,0xF0,0x3C,0x0C,0x00,0x08,0x0F,0x0F,0x00,0x01,0x0F,0x0E,0x00, // -K-

0x04,0xFC,0xFC,0x04,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x08,0x0C,0x0E,0x00, // -L-

0xFC,0xFC,0x38,0x70,0x38,0xFC,0xFC,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -M-

0xFC,0xFC,0x38,0x70,0xE0,0xFC,0xFC,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -N-

0xF0,0xF8,0x0C,0x04,0x0C,0xF8,0xF0,0x00,0x03,0x07,0x0C,0x08,0x0C,0x07,0x03,0x00, // -O-

0x04,0xFC,0xFC,0x44,0x44,0x7C,0x38,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -P-

0xF8,0xFC,0x04,0x04,0x04,0xFC,0xF8,0x00,0x07,0x0F,0x08,0x0E,0x3C,0x3F,0x27,0x00, // -Q-

0x04,0xFC,0xFC,0x44,0xC4,0xFC,0x38,0x00,0x08,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x00, // -R-

0x18,0x3C,0x64,0x44,0xC4,0x9C,0x18,0x00,0x06,0x0E,0x08,0x08,0x08,0x0F,0x07,0x00, // -S-

0x00,0x1C,0x0C,0xFC,0xFC,0x0C,0x1C,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -T-

0xFC,0xFC,0x00,0x00,0x00,0xFC,0xFC,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -U-

0xFC,0xFC,0x00,0x00,0x00,0xFC,0xFC,0x00,0x01,0x03,0x06,0x0C,0x06,0x03,0x01,0x00, // -V-

0xFC,0xFC,0x00,0x80,0x00,0xFC,0xFC,0x00,0x03,0x0F,0x0E,0x03,0x0E,0x0F,0x03,0x00, // -W-

0x0C,0x3C,0xF0,0xC0,0xF0,0x3C,0x0C,0x00,0x0C,0x0F,0x03,0x00,0x03,0x0F,0x0C,0x00, // -X-

0x00,0x3C,0x7C,0xC0,0xC0,0x7C,0x3C,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -Y-

0x1C,0x0C,0x84,0xC4,0x64,0x3C,0x1C,0x00,0x0E,0x0F,0x09,0x08,0x08,0x0C,0x0E,0x00, // -Z-

0x00,0x00,0xFC,0xFC,0x04,0x04,0x00,0x00,0x00,0x00,0x0F,0x0F,0x08,0x08,0x00,0x00, // -[-

0x38,0x70,0xE0,0xC0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x07,0x0E,0x00, // --

0x00,0x00,0x04,0x04,0xFC,0xFC,0x00,0x00,0x00,0x00,0x08,0x08,0x0F,0x0F,0x00,0x00, // -]-

0x08,0x0C,0x06,0x03,0x06,0x0C,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -^-

0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, // -_-

0x00,0x00,0x03,0x07,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -`-

0x00,0xA0,0xA0,0xA0,0xE0,0xC0,0x00,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -a-

0x04,0xFC,0xFC,0x20,0x60,0xC0,0x80,0x00,0x08,0x0F,0x07,0x08,0x08,0x0F,0x07,0x00, // -b-

0xC0,0xE0,0x20,0x20,0x20,0x60,0x40,0x00,0x07,0x0F,0x08,0x08,0x08,0x0C,0x04,0x00, // -c-

0x80,0xC0,0x60,0x24,0xFC,0xFC,0x00,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -d-

0xC0,0xE0,0xA0,0xA0,0xA0,0xE0,0xC0,0x00,0x07,0x0F,0x08,0x08,0x08,0x0C,0x04,0x00, // -e-

0x40,0xF8,0xFC,0x44,0x0C,0x18,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -f-

0xC0,0xE0,0x20,0x20,0xC0,0xE0,0x20,0x00,0x27,0x6F,0x48,0x48,0x7F,0x3F,0x00,0x00, // -g-

0x04,0xFC,0xFC,0x40,0x20,0xE0,0xC0,0x00,0x08,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x00, // -h-

0x00,0x00,0x20,0xEC,0xEC,0x00,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -i-

0x00,0x00,0x00,0x00,0x20,0xEC,0xEC,0x00,0x00,0x30,0x70,0x40,0x40,0x7F,0x3F,0x00, // -j-

0x04,0xFC,0xFC,0x80,0xC0,0x60,0x20,0x00,0x08,0x0F,0x0F,0x01,0x03,0x0E,0x0C,0x00, // -k-

0x00,0x00,0x04,0xFC,0xFC,0x00,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -l-

0xE0,0xE0,0x60,0xC0,0x60,0xE0,0xC0,0x00,0x0F,0x0F,0x00,0x0F,0x00,0x0F,0x0F,0x00, // -m-

0x20,0xE0,0xC0,0x20,0x20,0xE0,0xC0,0x00,0x00,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x00, // -n-

0xC0,0xE0,0x20,0x20,0x20,0xE0,0xC0,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -o-

0x20,0xE0,0xC0,0x20,0x20,0xE0,0xC0,0x00,0x40,0x7F,0x7F,0x48,0x08,0x0F,0x07,0x00, // -p-

0xC0,0xE0,0x20,0x20,0xC0,0xE0,0x20,0x00,0x07,0x0F,0x08,0x48,0x7F,0x7F,0x40,0x00, // -q-

0x20,0xE0,0xC0,0x60,0x20,0x60,0xC0,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -r-

0x40,0xE0,0xA0,0x20,0x20,0x60,0x40,0x00,0x04,0x0C,0x09,0x09,0x0B,0x0E,0x04,0x00, // -s-

0x20,0x20,0xF8,0xFC,0x20,0x20,0x00,0x00,0x00,0x00,0x07,0x0F,0x08,0x0C,0x04,0x00, // -t-

0xE0,0xE0,0x00,0x00,0xE0,0xE0,0x00,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -u-

0x00,0xE0,0xE0,0x00,0x00,0xE0,0xE0,0x00,0x00,0x03,0x07,0x0C,0x0C,0x07,0x03,0x00, // -v-

0xE0,0xE0,0x00,0x00,0x00,0xE0,0xE0,0x00,0x07,0x0F,0x0C,0x07,0x0C,0x0F,0x07,0x00, // -w-

0x20,0x60,0xC0,0x80,0xC0,0x60,0x20,0x00,0x08,0x0C,0x07,0x03,0x07,0x0C,0x08,0x00, // -x-

0xE0,0xE0,0x00,0x00,0x00,0xE0,0xE0,0x00,0x47,0x4F,0x48,0x48,0x68,0x3F,0x1F,0x00, // -y-

0x60,0x60,0x20,0xA0,0xE0,0x60,0x20,0x00,0x0C,0x0E,0x0B,0x09,0x08,0x0C,0x0C,0x00, // -z-

0x00,0x40,0x40,0xF8,0xBC,0x04,0x04,0x00,0x00,0x00,0x00,0x07,0x0F,0x08,0x08,0x00, // -{-

0x00,0x00,0x00,0xBC,0xBC,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x0F,0x00,0x00,0x00, // -|-

0x00,0x04,0x04,0xBC,0xF8,0x40,0x40,0x00,0x00,0x08,0x08,0x0F,0x07,0x00,0x00,0x00, // -}-

0x08,0x0C,0x04,0x0C,0x08,0x0C,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -~-

0x80,0xC0,0x60,0x30,0x60,0xC0,0x80,0x00,0x07,0x07,0x04,0x04,0x04,0x07,0x07,0x00, // --

/*-- 调入了一幅图像：C:Documents and SettingsAdministrator桌面12864.bmp --*/

0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x80,0x00,0x00,0x00,

0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x20,0x20,0x20,0x20,0x20,0x20,

0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x20,0x20,0x00,0x00,0x00,0x00,

0x20,0xE0,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

0x00,0x00,0x00,0x00,0xF8,0x06,0x01,0x00,0x00,0x00,0x00,0x01,0x07,0x00,0x00,0xFC,

0x81,0x87,0x80,0x00,0x00,0x00,0x00,0x00,0x80,0x1F,0x12,0x12,0xF2,0x12,0x12,0x12,

0xE8,0x28,0x08,0x08,0xF8,0x08,0x08,0x28,0x48,0x88,0x08,0x08,0x04,0x00,0x00,0x00,

0x11,0x11,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

0x00,0x00,0x00,0x00,0x03,0x0C,0x08,0x10,0x10,0x10,0x10,0x08,0x06,0x00,0x00,0x03,

0x10,0x0F,0x00,0x00,0x00,0x20,0x20,0x20,0x21,0x2E,0x24,0x20,0x3F,0x20,0x20,0x20,

0x00,0x20,0x20,0x60,0x7F,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x0C,0x00,0x00,0x00,

0x01,0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,

0x20,0xC0,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0xE0,0x00,0x00,0x00,0x80,0x00,0x00,

0xF0,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,

0xC8,0x38,0x0C,0x10,0x10,0xD0,0x78,0x1E,0xD0,0x90,0x10,0x10,0x10,0x10,0x00,0x00,

0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x01,

0x0A,0xF1,0x00,0x00,0x00,0x31,0x11,0x1B,0x0A,0xFF,0x0A,0x1B,0x11,0x31,0x00,0x00,

0xFF,0xFF,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x7F,0x21,0x21,0x21,0x21,0x20,

0x41,0x62,0x3C,0x40,0x46,0x45,0x44,0x44,0xFF,0x44,0x44,0x44,0x42,0x60,0x40,0x00,

0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x02,0x03,0x02,0x02,0x00,0x00,0x00,0x00,0x03,

0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

0x03,0x03,0x02,0x02,0x00,0x00,0x00,0x0C,0x06,0x01,0x00,0x00,0x00,0x07,0x04,0x00,

0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x08,0x00,0x00,0x00,0x00,0x00,0x00,

0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

// 延时程序

{

while(ms--)

void Clear()

unsigned char i,j,m=0;

{

for(j=0;j<128;j++)

}

void LcdInit()

RES=0;

RES=1;

WrateC(0xA2);//Bais set

WrateC(0xc0);//com output scan direction，com镜像选择 0xc0正常，0xC8上下镜像

WrateC(0x2c);//内部电源管理，

WrateC(0x2F);//

WrateC(0x16);//电压调整寄存器低位范围：0x00-0x3f （微调）值越大，显示效果越浓（底影越浓）

WrateC(0x40);//从首行开始显示

}

void Hanzi_Disp(void) //显示图片程序

unsigned char i,j,k=0;

{

for(j=0;j<128;j++)

}

delay(5000);

void Display(unsigned char sda,unsigned char sda1)

unsigned char i,j;

{

WrateC(0x10);

for(j=0;j<128;j++)

WrateD(sda1);

}

void main()

LcdInit();

delay(5000);

Display(0xff,0x00);

Hanzi_Disp(void) //显示一幅图片

while(1);

void Setadd(uchar xl,uchar yl)

i=xl&0x0f; //i=(xl+0)&0x0f;（SEG0~SEG127） // i=(xl+4)&0x0f;（SEG4~SEG131）

WrateC(xl);

}

void WriteEnglish(uchar col,uchar pag,uchar *ptr)

uchar i,j;

while(*ptr)

c= *ptr;

for(i=0;i<2;i++)

Setadd(col,pag);

WrateD(fontASCII8x16[c][i*8+j]);

}

if(col>0x7f)

col=0;

}

pag-=2;

/*

{

C_S=0;

R_D=1;

W_R=1;

}

{

C_S=0;

R_D=1;

W_R=1;

}

/**********************************/

/************6800时序*************/

void WrateC(uchar cmd) //写入指令到LCD

R_S=0;//选择指令存储器

W_R=0;

P1=cmd;

W_R=1;

}

{

C_S=0;

R_D=1;

R_D=0;

C_S=1;

/*

unsigned char data i,j;

R_S=0;

for(i=0;i<8;i++)

j=com;

SDA=com&0x80;

com=j<<1;

C_S=1;

}

unsigned char data i,j;

R_S=1;

for(i=0;i<8;i++)

j=dat;

SDA=dat&0x80;

dat=j<<1;

C_S=1;

}

*/

/**********************************/

搜索历史

COG12864标准演示程序

相关推荐

评论

精选推荐

热门帖

站长推荐 /6