完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
我想在STM8A-DISCOVERY板上使用UART。
但是,AFAIK,STM8A RX和TX引脚未连接到电路板上的任何接头。 有开放的焊接桥将它们连接到ST-Link / v2接口。我可以将一些导线焊接到这些开路焊桥的STM8侧,以获得RX / TX信号。还有更好的想法? 菲利普 以上来自于谷歌翻译 以下为原文 I want to use the UART on the STM8A-DISCOVERY boards. However, AFAIK, the STM8A RX and TX pins are not connected to any header on the boards. There are open solder bridges connecting them to the ST-Link/v2 interface. I could just solder some wires to the STM8 side of these open solder bridges to get the RX/TX signals. Any better ideas? Philipp |
|
相关推荐
2个回答
|
|
由于我只需要将数据从STM8A-DISCOVERY传输到主机,因此我使用UART3而不是UART1。 UART3的Tx引脚是LIN跳线上的引脚1。
菲利普 以上来自于谷歌翻译 以下为原文 Since I only need to transmit data from the STM8A-DISCOVERY to the host, I used UART3 instead of UART1. The Tx pin of UART3 is pin 1 on the LIN jumper. Philipp |
|
|
|
同样,在STM8AL板上,UART1的Tx在LIN跳线pin1上可用。
菲利普 以上来自于谷歌翻译 以下为原文 Similarly, on the STM8AL board, the Tx of UART1 is available on the LIN jumper, pin1. Philipp |
|
|
|
只有小组成员才能发言,加入小组>>
请教:在使用UDE STK时,单片机使用SPC560D30L1,在配置文件怎么设置或选择?里面只有SPC560D40的选项
1209 浏览 1 评论
1832 浏览 1 评论
请问是否有通过UART连接的两个微处理器之间实现双向值交换的方法?
1498 浏览 1 评论
2724 浏览 6 评论
4945 浏览 21 评论
293浏览 4评论
339浏览 4评论
在Linux上安装Atollic TRUEStudio的步骤有哪些呢?
263浏览 3评论
使用DMA激活某些外设会以导致外设无法工作的方式生成代码是怎么回事
333浏览 3评论
346浏览 3评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-3-29 03:05 , Processed in 1.198357 second(s), Total 76, Slave 60 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 深圳华秋电子有限公司
电子发烧友 (电路图) 粤公网安备 44030402000349 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号