HP 8590A缺少HPIB/GPIB连接器和电缆

听起来您需要服务指南附图中的图片。
有一条带状电缆连接到电路板上，后面板上还连接有GPIB连接器。
从服务指南看，此程序集的部件号看起来是08590-60018。
对不起，但我根本找不到任何原理图，但这应该解决了电缆如何到达后面板连接器的秘密......我做了谷歌搜索部件号，我确实看到了至少一个
点击似乎是出售的合法报价。
最好的问候，迈克



     以下为原文

  It sounds like you need what is pictured in the attached drawing from the service guide. There is a ribbon cable attached to a board that also has the rear panel GPIB connector attached to it. From the service guide it looks like the part number of this assembly is 08590-60018. Sorry, but I couldn't find any schematics for this at all, but this should solve the mystery of how the cable gets to the rear panel connector...

I did a google search for the part number and I did see at least one hit come up that appeared to be a legitimate offer for one for sale.

Best regards,
Mike

附件

• Rear Panel.pdf697.7 KB
  

谢谢捆绑。
Dunno为什么我没有在服务指南中找到它？
（0850-90316，我能在网上找到的唯一一个）。
无论如何，如果我能找到一个完整的电缆和支架，价格合理，那就容易多了。
我会看看。
编辑：AndersG于2015年2月17日上午11:59啊..因为这是错误的手册。
正确的是08590-90109：http：//www.keysight.com/upload/cmc_upload/All/8590AServiceGuide.pdf编辑：AndersG于2015年2月17日下午11:32我猜测08590-60052 GPIB的手册
OPT Kit将包含接线说明，但我无法在网上找到它。编辑：AndersG于2015年2月17日下午11:48



     以下为原文

  Thanks a bundle. Dunno why I did not find that in the service guide? (0850-90316, the only one I could find on the web). Anyway, If I can find a complete cable and bracket, for a reasonable price, then it is so much easier. I will look.

Edited by: AndersG on Feb 17, 2015 11:59 AM

Ah.. Because it was the wrong manual. The correct one is 08590-90109:
http://www.keysight.com/upload/cmc_upload/All/8590AServiceGuide.pdf

Edited by: AndersG on Feb 17, 2015 11:32 PM

I Guess the manual for the 08590-60052 GPIB OPT Kit would contain wiring instructions, but I have been unable to locate it on the web.

Edited by: AndersG on Feb 17, 2015 11:48 PM

好。
取得了一些进展，电缆引脚似乎是：1,2,3,5,7,9,11,13 = gnd 4 atn 6 srq 8 ifc 10 ndac 12 nrfd 14 dav 15 ren 16 eoi 17 d8 18 d4 19 d7 20
d3 21 d6 22 d2 23 d5 24 d1我发现有一家供应商提供的电缆+支架只需50多美元，但最低订购量为200美元，运费将额外收取50美元。
一个gpib连接器和一个IDC连接器将让我回到不到10美元:)不知道是否应该屏蔽电缆？
当空闲时，OTOH应该不受GPIB电缆的辐射。



     以下为原文

  OK. Made some progress, cable pinout seems to be:

1,2,3,5,7,9,11,13 = gnd
4 atn
6 srq
8 ifc
10 ndac
12 nrfd
14 dav
15 ren
16 eoi
17 d8
18 d4
19 d7
20 d3
21 d6
22 d2
23 d5
24 d1

I found one vendor that offered the cable+bracket for just over 50$, ut they have a minimum order of 200$ and shipping will set me back an extra 50$. A gpib connector and an IDC one will set me back less than 10$ :)

Wonder if the cable should be screened? OTOH should the be no emissions from the GPIB cable when idle.