完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
嗨,
我有三个双极步进电机在4000Hz运行。另外两个工作正常。 我的问题是我的步进电机中有一个经常失速。 我观察到,当我只是握住它的手掌并以4Khz的速度运行时,它会不断地停转,但是当我用双手握住它时它不会停转。 有谁知道我的马达发生了什么事? 谢谢 啧啧 #stall #stepper-motor 以上来自于谷歌翻译 以下为原文 Hi, I have three bipolar stepper motor run at 4000Hz. The other two works ok. My problem is that 1 of my stepper motor constantly stall. I observed that when I just held it my palm and run it at 4Khz it constantly stall however when I hold it tight with my two hands it won't stall. Does anyone knows what's going on with my motor? Thanks Gee #stall #stepper-motor |
|
相关推荐
1个回答
|
|
亲爱的吉
请在https://my.st.com//public/STe2ecommunities/motordriver_ics/Lists/Motor%20Driver%20ICs%20and%20Boards/AllItems.aspx上发布与硬件相关的线程 论坛。 谢谢 再见 梁咏琪 注意:原始帖子包含大量线程对话,只能迁移到第9级 以上来自于谷歌翻译 以下为原文 Dear Gee Please post threads related to hardware in the https://my.st.com//public/STe2ecommunities/motordriver_ics/Lists/Motor%20Driver%20ICs%20and%20Boards/AllItems.aspx forum. Thanks Ciao Gigi Note: the original post contained a large number of threaded conversations and was only able to be migrated to the 9th level |
|
|
|
只有小组成员才能发言,加入小组>>
请教:在使用UDE STK时,单片机使用SPC560D30L1,在配置文件怎么设置或选择?里面只有SPC560D40的选项
1408 浏览 1 评论
2058 浏览 1 评论
请问是否有通过UART连接的两个微处理器之间实现双向值交换的方法?
1507 浏览 1 评论
2803 浏览 6 评论
5186 浏览 21 评论
351浏览 4评论
503浏览 4评论
在Linux上安装Atollic TRUEStudio的步骤有哪些呢?
276浏览 3评论
使用DMA激活某些外设会以导致外设无法工作的方式生成代码是怎么回事
561浏览 3评论
479浏览 3评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-4-20 09:06 , Processed in 0.859894 second(s), Total 70, Slave 58 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号