完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
我正在使用STSPIN32F0,客户板驱动客户电机,采用无传感器FOC算法(STM32_FOC_SDK_4.3.0.16508_161109)。
在低转速下行驶时,估算的角度似乎正常,电机正常启动。 但是当以高转速行驶时,估计的角度似乎偏移(延迟)并且电机非正常地驱动并且将停止。 我能为这个问题做些什么? 请帮帮我,谢谢! 以上来自于谷歌翻译 以下为原文 I am using STSPIN32F0, customer board to drive a customer motor with sensorless FOC algorithm (STM32_FOC_SDK_4.3.0.16508_161109). When drive in the low RPM, the angle estimated seems OK and the motor drived normally. But when drive in the high RPM, the angle estimated seems shifted (delay) and the motor drived non-normally and will stop. What can I do for this issue? Please help me, thank you! |
|
相关推荐
2个回答
|
|
即使我使用steval-spin3201运行更高转速的电机也存在同样的问题。我正在使用这种电机
https://hobbyking.com/en_us/c1826-micro-brushless-outrunner-2400kv-18g.html?___store=en_us ,我能够运行电机直到13000转,之后它会停转。电机的最大转速为26000.我在28000/2运行FOC。请帮帮我 以上来自于谷歌翻译 以下为原文 Even i have the same problem running higher rpm motor using steval-spin3201. I am using this motor https://hobbyking.com/en_us/c1826-micro-brushless-outrunner-2400kv-18g.html?___store=en_us , i could able to run the motor till 13000 rpm later it stalls .where as the max rpm of the motor is 26000. I am running FOC at 28000/2. please help me |
|
|
|
根据条件,STSPIN32F0的最大FOC速率为12kHz-15 kHz。这也是您可以实现的控制算法的最大带宽。
该频率根据电机的极对数限制了您可以达到的最大速度。 拇指规则: 最大速度[rpm] = fFOC / 10 x 60 / npp 其中fFOC是FOC速率,npp是电机的极对数。 以上来自于谷歌翻译 以下为原文 The maximum FOC rate of the STSPIN32F0 is 12kHz-15 kHz according to the conditions. This is also the maximum bandwidth of the control algorithm you can implement. This frequency limits the maximum speed you can reach according to the number of pole pairs of the motor. Thumb rule: max speed [rpm] = fFOC/10 x 60 / npp where fFOC is the FOC rate and npp is the number of pole pairs of the motor. |
|
|
|
只有小组成员才能发言,加入小组>>
请教:在使用UDE STK时,单片机使用SPC560D30L1,在配置文件怎么设置或选择?里面只有SPC560D40的选项
1454 浏览 1 评论
2122 浏览 1 评论
请问是否有通过UART连接的两个微处理器之间实现双向值交换的方法?
1510 浏览 1 评论
2826 浏览 6 评论
5245 浏览 21 评论
362浏览 4评论
542浏览 4评论
在Linux上安装Atollic TRUEStudio的步骤有哪些呢?
279浏览 3评论
使用DMA激活某些外设会以导致外设无法工作的方式生成代码是怎么回事
613浏览 3评论
514浏览 3评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2024-4-25 02:42 , Processed in 0.790496 second(s), Total 76, Slave 60 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号